E90Post
 


Extreme Power House
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Powertrain and Drivetrain Discussions > N54 Turbo Engine / Drivetrain / Exhaust Modifications - 335i > BT Scan Tool Found A LOT of fault codes!!! Am I in a serious trouble?



Reply
 
Thread Tools Search this Thread
      03-24-2009, 09:17 AM   #1
cocoturkey
Lieutenant
 
Drives: 08' e92 335i
Join Date: Jan 2008
Location: Taipei

Posts: 441
iTrader: (0)

BT Scan Tool Found A LOT of fault codes!!! Am I in a serious trouble?

I ran a short test with BT Scan Tool and found 17 errors codes... and i also found a lot of (shadow) fault codes in "Engine - N54 Fault Codes", "Engine - N54 Shadow Fault Codes", Transmission Fault Codes", "Car Access System Fault Codes", "Airbag Fault Codes", "Instrument Cluster Fault Codes" and "Steering Shadow Fault Codes"... Can anyone help me to intepreter these codes? am i in a very serious trouble?

P.S. I have Catless DPs, DCI and a piggyback installed...(I have O2 sim too)

__________________________________________________ ______________
____________________short test result___________________________
Short Test
Engine - N54
Current Fault Codes
________________________________________
29DC
29DC Cylinder injection switch-off
Error will cause a warning light
Error is not currently present
Test conditions have not been completed

________________________________________
2C73
2C73 Lambda probe behind catalytic converter, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2C74
2C74 Lambda probe behind catalytic converter 2, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2AAF
2AAF Fuel pump, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2D25
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2A96
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
3100
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
Fuel pump
No fault codes
________________________________________
Longitudinal mgmt
No fault codes
________________________________________
Power steering
No fault codes
________________________________________
Transmission
Current Fault Codes
________________________________________
51A6
Error engine signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold

________________________________________
Stability control
Current Fault Codes
________________________________________
5DA3
Yaw rate sensor: DRS sends signal DrsPSIP2=INITstatus error (DRS-Typ MM 3.x).
Error will cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
5D93
Valve relay: Medium or high-resistance short circuit of voltage supply FR or valve after ground registered through start-up test.
Error will cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
5E1A
DSC-ECU: ECU-internal: Serial-Peripheral-Interface (SPI): Transmission failure multi IC.
Error will cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
Transfer case
No fault codes
________________________________________
Air conditioner
No fault codes
________________________________________
Light control
No fault codes
________________________________________
Car Access System
Current Fault Codes
________________________________________
A0B5
Signal identification peed error
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
Junction box
No fault codes
________________________________________
Instrument cluster
Current Fault Codes
________________________________________
A559
Clamp 30g_f cutoff
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
Rain / light sensor
No fault codes
________________________________________
Telematic
No fault codes
________________________________________
Airbags
Current Fault Codes
________________________________________
93FB
SBR - function - Velocity signal missing
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Timeout

________________________________________
Roof control
No fault codes
________________________________________
Seat module - driver
No fault codes
________________________________________
Radio
No fault codes
________________________________________
Radio gateway
No fault codes
________________________________________
Steering
No fault codes
________________________________________
Convertible top
No fault codes
________________________________________
Trailer
No fault codes
________________________________________
Park distance
No fault codes
________________________________________
Central control - low
No fault codes
________________________________________



















__________________________________________________ _______________
__________________________________________________ _______________
Module Identification: MSD80/MSD81 Engine module for N54 (Fault Codes)
________________________________________
Hardware Number XXXXX
Hardware Version Number 00
Coding Index 17
Diagnostic Index 0000
System Name XXXXX
Date Of ECU-Manufacturing 20080327
System Supplier Siemens
Message Catalogue Version 0.0.0
Software Version 0.0.0

MSD80/MSD81 Engine module for N54
Current Fault Codes
________________________________________
29DC:
29DC Cylinder injection switch-off
Error will cause a warning light
Error is not currently present
Test conditions have not been completed

Event 1
Odometer 6824kms 4240miles
Engine temperature 99.00 C
air mass calculated 450.35 mg/stk
Engine speed 1,856.00 rpm
fuel tank filling level 0.00 l


________________________________________
2C73:
2C73 Lambda probe behind catalytic converter, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s


________________________________________
2C74:
2C74 Lambda probe behind catalytic converter 2, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s


________________________________________
2AAF:
2AAF Fuel pump, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10880kms 6760miles
fuel pressure before mass control valve 5,264.27 hPa
Engine speed 2,592.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h

Event 2
Odometer 11176kms 6944miles
fuel pressure before mass control valve 4,924.64 hPa
Engine speed 5,056.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h


________________________________________
2D25:
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption


________________________________________
2A96:
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 11192kms 6954miles
Engine speed 6,752.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.71 V

Event 2
Odometer 11192kms 6954miles
Engine speed 6,912.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.61 V

Event 3
Odometer 11256kms 6994miles
Engine speed 6,816.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.81 V


________________________________________
3100:
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed


________________________________________




Module Identification: MSD80/MSD81 Engine module for N54 (Shadow Fault Codes)
________________________________________
Hardware Number 7586933
Hardware Version Number 00
Coding Index 17
Diagnostic Index 0000
System Name 4131
Date Of ECU-Manufacturing 20080327
System Supplier Siemens
Message Catalogue Version 0.0.0
Software Version 0.0.0

MSD80/MSD81 Engine module for N54
Current Shadow Fault Codes
________________________________________
2DC5:
2DC5 Torque requirement via CAN controller area network, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

Event 1
Odometer 6768kms 4205miles
Engine speed 1,184.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.68 V
status motor control 2.00 0-n

Event 2
Odometer 6768kms 4205miles
Engine speed 1,056.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.48 V
status motor control 2.00 0-n

Event 3
Odometer 12080kms 7506miles
Engine speed 928.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.58 V
status motor control 2.00 0-n


________________________________________
29DC:
29DC Cylinder injection switch-off
Error will cause a warning light
Error is not currently present
Test conditions have not been completed

Event 1
Odometer 6824kms 4240miles
Engine temperature 99.00 C
air mass calculated 450.35 mg/stk
Engine speed 1,856.00 rpm
fuel tank filling level 0.00 l


________________________________________
2C73:
2C73 Lambda probe behind catalytic converter, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s


________________________________________
2C74:
2C74 Lambda probe behind catalytic converter 2, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s


________________________________________
2AAF:
2AAF Fuel pump, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10880kms 6760miles
fuel pressure before mass control valve 5,264.27 hPa
Engine speed 2,592.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h

Event 2
Odometer 11176kms 6944miles
fuel pressure before mass control valve 4,924.64 hPa
Engine speed 5,056.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h


________________________________________
2D25:
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption


________________________________________
2A96:
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 11192kms 6954miles
Engine speed 6,752.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.71 V

Event 2
Odometer 11192kms 6954miles
Engine speed 6,912.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.61 V

Event 3
Odometer 11256kms 6994miles
Engine speed 6,816.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.81 V


________________________________________
3100:
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed


________________________________________




Transmission Current Fault Codes
________________________________________
51A6:
Error engine signal
Error will not cause a warning light
Error is not currently present
Test conditions have not been completed
Signal or value below threshold



Car Access System 3
Current Fault Codes
________________________________________
A0B5:
Signal identification peed error
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption




Current Fault Codes
________________________________________
A559:
Clamp 30g_f cutoff
Error will not cause a warning light
Error is not currently present
Test conditions have been completed





instrument cluster fault codes
Multi-restraint system
Current Fault Codes
________________________________________
93FB:
SBR - function - Velocity signal missing
Error will not cause a warning light
Error is not currently present
Test conditions have not been completed
Timeout




Steering Shadow Fault Codes
Active front steering for E90
Current Shadow Fault Codes
________________________________________
7015:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
7017:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
703D:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
7119:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed
cocoturkey is offline   Taiwan
0
Reply With Quote
      03-24-2009, 09:29 AM   #2
J.P.
Close to bein Bannned
 
J.P.'s Avatar
 
Drives: Pussy Magnet
Join Date: May 2008
Location: Hunterdon, NJ

Posts: 5,068
iTrader: (0)

Send a message via AIM to J.P.
holy shit!

what tune are you running?
__________________

Quote:
Originally Posted by sexye92 View Post
JERRYS MOM= BEST HEAD OF MY LIFE
J.P. is offline   United_States
0
Reply With Quote
      03-24-2009, 09:38 AM   #3
MrWhite1015
Major General
 
MrWhite1015's Avatar
 
Drives: MINIVAN
Join Date: Aug 2008
Location: Westchester NY

Posts: 6,020
iTrader: (21)

Garage List
Send a message via AIM to MrWhite1015
really.... you has to go there and start that ... how about offering the op some advice or help...

op they have a list of error codes on n54tech.com might wanna go post this there as well
__________________
MrWhite1015 is offline  
0
Reply With Quote
      03-24-2009, 09:44 AM   #4
dmurray14
The Stig
 
dmurray14's Avatar
 
Drives: Quickly
Join Date: Apr 2005
Location: US

Posts: 1,231
iTrader: (1)

I'm no expert, but the majority might be from unplugging the ECU connector while it was still "awake." I think the 2D25 and 2AAF are fairly self explanatory, and are talked about a lot on here. Which tune?
__________________
dmurray14 is offline   United_States
0
Reply With Quote
      03-24-2009, 09:49 AM   #5
Ilma
Colonel
 
Drives: BMW
Join Date: Nov 2008
Location: hometown

Posts: 2,535
iTrader: (0)

It looks like the OP is running a Procede given the crankshaft tooth code.

And yes....the majority of those codes look like they are signal based interuptions - indicating something was not hooked up correctly.

Looks like there was probably a limp mode as well.

They can all be cleared with BT tool, but you should troubleshoot your ECU connections to find whether that is the root cause.

Also....another possiblity is you may have been updating maps with the engine running - which according to Shiv is not recommended.
Ilma is online now  
0
Reply With Quote
      03-24-2009, 09:59 AM   #6
RiXst3r
 
RiXst3r's Avatar
 
Drives: www.p3cars.com
Join Date: Sep 2006
Location: Ohio

Posts: 6,459
iTrader: (14)

Send a message via AIM to RiXst3r
Looks like at one point during a piggyback installation, you tried to start the car without the ECU connector fully seated.

Or, as others have said, disconnected the ECU while it was still awake.
RiXst3r is offline  
0
Reply With Quote
      03-24-2009, 10:27 AM   #7
J.P.
Close to bein Bannned
 
J.P.'s Avatar
 
Drives: Pussy Magnet
Join Date: May 2008
Location: Hunterdon, NJ

Posts: 5,068
iTrader: (0)

Send a message via AIM to J.P.
Quote:
Originally Posted by MrWhite1015 View Post
really.... you has to go there and start that ... how about offering the op some advice or help...

op they have a list of error codes on n54tech.com might wanna go post this there as well
Im not starting a "tuner war" He said he's running a piggy back, it would help to know which one, If it's a procede than maybe shiv can chime in?
__________________

Quote:
Originally Posted by sexye92 View Post
JERRYS MOM= BEST HEAD OF MY LIFE
J.P. is offline   United_States
0
Reply With Quote
      03-24-2009, 10:28 AM   #8
techforge
Lieutenant
 
Drives: 335xi coupe
Join Date: Jul 2008
Location: Denver

Posts: 577
iTrader: (2)

Why not clear all the codes and see if any return after a few miles and focus on those?
techforge is offline   United_States
0
Reply With Quote
      03-24-2009, 10:58 AM   #9
mid-corner fun
Major
 
Drives: e92
Join Date: Jun 2005
Location: NE

Posts: 1,385
iTrader: (3)

I posted something similar a month ago, BT scan showed a ton of codes, cleared them and they never came back.
mid-corner fun is offline   United_States
0
Reply With Quote
      03-24-2009, 11:11 AM   #10
shiv@vishnu
Tuner
 
shiv@vishnu's Avatar
 
Drives: X1, 335i
Join Date: Sep 2006
Location: SF Bay, CA

Posts: 17,611
iTrader: (0)

looks like you tried to start the car with an ecu connector disconnected a couple of times. Or tried to update fimware with the engine running. To disconncted the Procede before the DME went to sleep. No harm done. Just clear it all and be on your way. As for the manipulation code, just make sure you are running doomsday map with default settings. But you probably don't care about that anymore given your ability to clear codes now.

Shiv
shiv@vishnu is offline   United_States
0
Reply With Quote
      03-24-2009, 11:49 AM   #11
ezatnova
Colonel
 
ezatnova's Avatar
 
Drives: C63 AMG
Join Date: Jan 2006
Location: West Chester, PA

Posts: 2,188
iTrader: (5)

Simply baffling to me that people continue to install/remove piggies with the battery still connected. For crying out loud, it takes under 20 seconds to disconnect the battery. Why WAIT for the car to "sleep"?? Sorry for mildly OT rant.
ezatnova is offline   United_States
0
Reply With Quote
      03-24-2009, 12:49 PM   #12
Crisp
Lieutenant Colonel
 
Crisp's Avatar
 
Drives: E60 M5 6 Speed
Join Date: Jun 2008
Location: NYC

Posts: 1,521
iTrader: (1)

Quote:
Originally Posted by ezatnova View Post
Simply baffling to me that people continue to install/remove piggies with the battery still connected. For crying out loud, it takes under 20 seconds to disconnect the battery. Why WAIT for the car to "sleep"?? Sorry for mildly OT rant.

There could be other causes too.

I probably have these codes throw even though I always disconnected the battery every time I installed/uninstalled my tune, BUT the first time I installed it, I plugged one cable into the wrong slot which caused the car to crank but not start. This probably threw codes that the ECU was disconnected with the battery on.

Can't wait for my BT to come in... I will definitely have pages of codes.
Crisp is offline   Albania
0
Reply With Quote
      03-24-2009, 01:50 PM   #13
cocoturkey
Lieutenant
 
Drives: 08' e92 335i
Join Date: Jan 2008
Location: Taipei

Posts: 441
iTrader: (0)

Thanks for everyone's input and adivce! I used the word "piggyback" instead of using the name of tune because I tried not to start a "tuen war"... I just wanted to know if I need to take my car in for medical attention or not. I was really scared when i first saw those codes!! btw, I never installed/disconnected the piggyback with the battery connected... (but I know the cause of most of the error codes now) I will try to clear all the codes and see if any of those codes show up again. I did expereince limp mode 3 times... Two of them were "Malfunction In Engine" and the last limp mode said "Malfunction In Engine" and "Malfunction In Transmission"... I've been limp mode free for 2 months since my last limp mode.
cocoturkey is offline   Taiwan
0
Reply With Quote
      03-24-2009, 02:57 PM   #14
J.P.
Close to bein Bannned
 
J.P.'s Avatar
 
Drives: Pussy Magnet
Join Date: May 2008
Location: Hunterdon, NJ

Posts: 5,068
iTrader: (0)

Send a message via AIM to J.P.
Quote:
Originally Posted by cocoturkey View Post
Thanks for everyone's input and adivce! I used the word "piggyback" instead of using the name of tune because I tried not to start a "tuen war"... I just wanted to know if I need to take my car in for medical attention or not. I was really scared when i first saw those codes!! btw, I never installed/disconnected the piggyback with the battery connected... (but I know the cause of most of the error codes now) I will try to clear all the codes and see if any of those codes show up again. I did expereince limp mode 3 times... Two of them were "Malfunction In Engine" and the last limp mode said "Malfunction In Engine" and "Malfunction In Transmission"... I've been limp mode free for 2 months since my last limp mode.
Good to hear.
yeah and don't worry about posting the piggybacks name, people will blame you for starting a "tuner war" at just about every chance they get.
__________________

Quote:
Originally Posted by sexye92 View Post
JERRYS MOM= BEST HEAD OF MY LIFE
J.P. is offline   United_States
0
Reply With Quote
      03-24-2009, 04:09 PM   #15
roadkillrob
Brigadier General
 
Drives: 2008 335Cic, 2011 X5 35i
Join Date: Jul 2007
Location: Boston

Posts: 3,798
iTrader: (14)

Wow - looks like you have a tune and other mods and drive the hell out of it. If your going into the dealer, I would pull the mods, clear the codes and drive it for a bit and see if anything comes back. There are lots of codes that don't mean much that are on most cars, but if the dealer sees that, you are done!
__________________

2008 E93 335i, GIAC Stage 2, HPF IC, Injen Intake, Defective AR Design DP's with useless cats
2014 X3 35i JB Stage 1
roadkillrob is offline   United_States
0
Reply With Quote
      03-24-2009, 04:21 PM   #16
E82tt6
Colonel
 
E82tt6's Avatar
 
Drives: '08 Black Saphire Z4 MC
Join Date: Oct 2007
Location: New Jersey

Posts: 2,629
iTrader: (0)

I had some of these from failing to seat the connectors fully.

A few of these look like implausability/manipulation codes though. I'd clear and check for them again in a few hundred miles.
__________________
'08 Black Saphire/Black Z4 M Coupe
RIP Gretta: Blue Water/Lemon 135i. Died to save me.
-ChuckV
E82tt6 is offline  
0
Reply With Quote
      03-25-2009, 08:14 AM   #17
Ilma
Colonel
 
Drives: BMW
Join Date: Nov 2008
Location: hometown

Posts: 2,535
iTrader: (0)

Quote:
Originally Posted by cocoturkey View Post
"... I've been limp mode free for 2 months since my last limp mode.

Lol....glad to see the 12 step program is working for you!

Sounds like it was a stressful situation for a little while.


Ilma is online now  
0
Reply With Quote
      03-26-2009, 10:45 AM   #18
cocoturkey
Lieutenant
 
Drives: 08' e92 335i
Join Date: Jan 2008
Location: Taipei

Posts: 441
iTrader: (0)

okay... i cleared all the codes and everything is alright until last night... i was running from 30km/h to 200km/h... and DSC warming light lighted up for 2 or 3 seconds and then engine malfuction light came up and i was in limp mode. The weird thing is that I was running "stock/valet map"!!! I shut the engine off... and switch it to "non-stock/non-valet" map, and running from 30km/h to 200km/h with no problem!! limp mode only show up when i was on stock/valet map... it so weird!! I took out my BT Scant Tool and did a short test... this is what i found:

Does anyone know what the problem might be by looking at the test result? Thank you very much!!


Short Test
Engine - N54
Current Fault Codes
2A96
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

3100
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

2D25
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Transmission
Current Fault Codes
51A6
Error engine signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold

Stability control
Current Fault Codes
5E1A
DSC-ECU: ECU-internal: Serial-Peripheral-Interface (SPI): Transmission failure multi IC.
Error will cause a warning light
Error is not currently present
Test conditions have been completed

************************************************** ******
************************************************** ******
Current Fault Codes
2A96:
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 12312kms 7650miles
Engine speed 6,816.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.71 V




3100:
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed


2D25:
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

************************************************** ******
************************************************** ******

MSD80/MSD81 Engine module for N54
Current Shadow Fault Codes
2DC5:
2DC5 Torque requirement via CAN controller area network, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

Event 1
Odometer 12240kms 7605miles
Engine speed 864.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.68 V
status motor control 2.00 0-n



Event 2
Odometer 12240kms 7605miles
Engine speed 1,152.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.98 V
status motor control 2.00 0-n



Event 3
Odometer 12384kms 7695miles
Engine speed 864.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.88 V
status motor control 2.00 0-n




2A96:
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 12312kms 7650miles
Engine speed 6,816.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.71 V




3100:
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed


2D25:
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption


************************************************** ******
************************************************** ******
Dynamic stability control DXC8 Plus - E90
Current Fault Codes
5E1A:
DSC-ECU: ECU-internal: Serial-Peripheral-Interface (SPI): Transmission failure multi IC.
Error will cause a warning light
Error is not currently present
Test conditions have been completed
************************************************** ******
************************************************** ******
Gearbox control unit
Current Fault Codes
51A6:
Error engine signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold
cocoturkey is offline   Taiwan
0
Reply With Quote
      03-26-2009, 10:57 AM   #19
shiv@vishnu
Tuner
 
shiv@vishnu's Avatar
 
Drives: X1, 335i
Join Date: Sep 2006
Location: SF Bay, CA

Posts: 17,611
iTrader: (0)

I think I know what a going on. PM me your number and we can go over a few things on the phone. A couple of things to check.
shiv@vishnu is offline   United_States
0
Reply With Quote
      03-26-2009, 11:02 AM   #20
BMW///Motorsport
First Lieutenant
 
BMW///Motorsport's Avatar
 
Drives: e92 335i
Join Date: Oct 2007
Location: Venice, CA

Posts: 382
iTrader: (1)

Quote:
Originally Posted by cocoturkey View Post
I ran a short test with BT Scan Tool and found 17 errors codes... and i also found a lot of (shadow) fault codes in "Engine - N54 Fault Codes", "Engine - N54 Shadow Fault Codes", Transmission Fault Codes", "Car Access System Fault Codes", "Airbag Fault Codes", "Instrument Cluster Fault Codes" and "Steering Shadow Fault Codes"... Can anyone help me to intepreter these codes? am i in a very serious trouble?

P.S. I have Catless DPs, DCI and a piggyback installed...(I have O2 sim too)

__________________________________________________ ______________
____________________short test result___________________________
Short Test
Engine - N54
Current Fault Codes
________________________________________
29DC
29DC Cylinder injection switch-off
Error will cause a warning light
Error is not currently present
Test conditions have not been completed

________________________________________
2C73
2C73 Lambda probe behind catalytic converter, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2C74
2C74 Lambda probe behind catalytic converter 2, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2AAF
2AAF Fuel pump, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2D25
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2A96
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
3100
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
Fuel pump
No fault codes
________________________________________
Longitudinal mgmt
No fault codes
________________________________________
Power steering
No fault codes
________________________________________
Transmission
Current Fault Codes
________________________________________
51A6
Error engine signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold

________________________________________
Stability control
Current Fault Codes
________________________________________
5DA3
Yaw rate sensor: DRS sends signal DrsPSIP2=INITstatus error (DRS-Typ MM 3.x).
Error will cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
5D93
Valve relay: Medium or high-resistance short circuit of voltage supply FR or valve after ground registered through start-up test.
Error will cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
5E1A
DSC-ECU: ECU-internal: Serial-Peripheral-Interface (SPI): Transmission failure multi IC.
Error will cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
Transfer case
No fault codes
________________________________________
Air conditioner
No fault codes
________________________________________
Light control
No fault codes
________________________________________
Car Access System
Current Fault Codes
________________________________________
A0B5
Signal identification peed error
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
Junction box
No fault codes
________________________________________
Instrument cluster
Current Fault Codes
________________________________________
A559
Clamp 30g_f cutoff
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
Rain / light sensor
No fault codes
________________________________________
Telematic
No fault codes
________________________________________
Airbags
Current Fault Codes
________________________________________
93FB
SBR - function - Velocity signal missing
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Timeout

________________________________________
Roof control
No fault codes
________________________________________
Seat module - driver
No fault codes
________________________________________
Radio
No fault codes
________________________________________
Radio gateway
No fault codes
________________________________________
Steering
No fault codes
________________________________________
Convertible top
No fault codes
________________________________________
Trailer
No fault codes
________________________________________
Park distance
No fault codes
________________________________________
Central control - low
No fault codes
________________________________________



















__________________________________________________ _______________
__________________________________________________ _______________
Module Identification: MSD80/MSD81 Engine module for N54 (Fault Codes)
________________________________________
Hardware Number XXXXX
Hardware Version Number 00
Coding Index 17
Diagnostic Index 0000
System Name XXXXX
Date Of ECU-Manufacturing 20080327
System Supplier Siemens
Message Catalogue Version 0.0.0
Software Version 0.0.0

MSD80/MSD81 Engine module for N54
Current Fault Codes
________________________________________
29DC:
29DC Cylinder injection switch-off
Error will cause a warning light
Error is not currently present
Test conditions have not been completed

Event 1
Odometer 6824kms 4240miles
Engine temperature 99.00 C
air mass calculated 450.35 mg/stk
Engine speed 1,856.00 rpm
fuel tank filling level 0.00 l


________________________________________
2C73:
2C73 Lambda probe behind catalytic converter, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s


________________________________________
2C74:
2C74 Lambda probe behind catalytic converter 2, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s


________________________________________
2AAF:
2AAF Fuel pump, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10880kms 6760miles
fuel pressure before mass control valve 5,264.27 hPa
Engine speed 2,592.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h

Event 2
Odometer 11176kms 6944miles
fuel pressure before mass control valve 4,924.64 hPa
Engine speed 5,056.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h


________________________________________
2D25:
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption


________________________________________
2A96:
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 11192kms 6954miles
Engine speed 6,752.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.71 V

Event 2
Odometer 11192kms 6954miles
Engine speed 6,912.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.61 V

Event 3
Odometer 11256kms 6994miles
Engine speed 6,816.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.81 V


________________________________________
3100:
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed


________________________________________




Module Identification: MSD80/MSD81 Engine module for N54 (Shadow Fault Codes)
________________________________________
Hardware Number 7586933
Hardware Version Number 00
Coding Index 17
Diagnostic Index 0000
System Name 4131
Date Of ECU-Manufacturing 20080327
System Supplier Siemens
Message Catalogue Version 0.0.0
Software Version 0.0.0

MSD80/MSD81 Engine module for N54
Current Shadow Fault Codes
________________________________________
2DC5:
2DC5 Torque requirement via CAN controller area network, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

Event 1
Odometer 6768kms 4205miles
Engine speed 1,184.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.68 V
status motor control 2.00 0-n

Event 2
Odometer 6768kms 4205miles
Engine speed 1,056.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.48 V
status motor control 2.00 0-n

Event 3
Odometer 12080kms 7506miles
Engine speed 928.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.58 V
status motor control 2.00 0-n


________________________________________
29DC:
29DC Cylinder injection switch-off
Error will cause a warning light
Error is not currently present
Test conditions have not been completed

Event 1
Odometer 6824kms 4240miles
Engine temperature 99.00 C
air mass calculated 450.35 mg/stk
Engine speed 1,856.00 rpm
fuel tank filling level 0.00 l


________________________________________
2C73:
2C73 Lambda probe behind catalytic converter, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s


________________________________________
2C74:
2C74 Lambda probe behind catalytic converter 2, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s


________________________________________
2AAF:
2AAF Fuel pump, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10880kms 6760miles
fuel pressure before mass control valve 5,264.27 hPa
Engine speed 2,592.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h

Event 2
Odometer 11176kms 6944miles
fuel pressure before mass control valve 4,924.64 hPa
Engine speed 5,056.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h


________________________________________
2D25:
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption


________________________________________
2A96:
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 11192kms 6954miles
Engine speed 6,752.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.71 V

Event 2
Odometer 11192kms 6954miles
Engine speed 6,912.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.61 V

Event 3
Odometer 11256kms 6994miles
Engine speed 6,816.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.81 V


________________________________________
3100:
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed


________________________________________




Transmission Current Fault Codes
________________________________________
51A6:
Error engine signal
Error will not cause a warning light
Error is not currently present
Test conditions have not been completed
Signal or value below threshold



Car Access System 3
Current Fault Codes
________________________________________
A0B5:
Signal identification peed error
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption




Current Fault Codes
________________________________________
A559:
Clamp 30g_f cutoff
Error will not cause a warning light
Error is not currently present
Test conditions have been completed





instrument cluster fault codes
Multi-restraint system
Current Fault Codes
________________________________________
93FB:
SBR - function - Velocity signal missing
Error will not cause a warning light
Error is not currently present
Test conditions have not been completed
Timeout




Steering Shadow Fault Codes
Active front steering for E90
Current Shadow Fault Codes
________________________________________
7015:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
7017:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
703D:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
7119:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed
PIGGYBACK Tunes at their finest! Throwing engine codes galore! Not on my whips...
__________________
2007 e92 335i / 6MT / ZSP / ZPP / Black Sapphire / JB+ / Vorsteiner Wheels / Brembo BBK / Borla Exhaust /
BMW///Motorsport is offline   United_States
0
Reply With Quote
      03-26-2009, 11:04 AM   #21
335lvr
Major
 
335lvr's Avatar
 
Drives: E92
Join Date: Jan 2007
Location: California

Posts: 1,441
iTrader: (4)

Maybe a bad firmware update? Strange only in valet.

OP: Please update when the solution is found.
__________________
"I'm not sure what the price difference is, but the BMW feels $15,000 better." -Edmunds, 2007

Last edited by 335lvr; 03-26-2009 at 04:34 PM.
335lvr is offline   United_States
0
Reply With Quote
      03-26-2009, 04:30 PM   #22
uuni
Second Lieutenant
 
Drives: 335i Cabrio
Join Date: Apr 2007
Location: Helsinki, Finland

Posts: 228
iTrader: (0)

Quote:
Originally Posted by BMW///Motorsport View Post
PIGGYBACK Tunes at their finest! Throwing engine codes galore! Not on my whips...
Nice work on taking that whole post as quote and then posting something useless.
__________________
AW, Coral red, Piano Black,Aero lip, M-sport (except front), M6 reps, M3 lip, interior "xenon" kit, Aluminium Pedals,H&R swaybars, KW V2, Quiafe LSD, OEM Strut Brace, BMS DCI, DIY Air Scoops i-tech BT handsfree,Braille battery (-20kg), Supersprint/Borla exhaust
uuni is offline   Finland
0
Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 08:54 PM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST