6AT Trans Upgrade options

SIKH335 · 02-12-2013, 10:06 PM

Ok guys quick update the car is heading to FFtec to pull the trans and is being shipped out to Sam @ 517Trans. Lets keep our fingers crossed Sam seems very knowledgable and confident that his rebuild and upgrade will hold my Single Turbos power. If all goes well I will be all over the 60-130 numbers right away and will make my way to Sacramento for some 1/4 mile runs. Fingers crossed!!!!

Dmacc · 02-12-2013, 10:12 PM

Quote:

Originally Posted by SIKH335

Ok guys quick update the car is heading to FFtec to pull the trans and is being shipped out to Sam @ 517Trans. Lets keep our fingers crossed Sam seems very knowledgable and confident that his rebuild and upgrade will hold my Single Turbos power. If all goes well I will be all over the 60-130 numbers right away and will make my way to Sacramento for some 1/4 mile runs. Fingers crossed!!!!

Good luck! Your car is going to be scary fast! This means you'll be able to up your boost to MT single turbo guys correct?

Vigorous · 02-12-2013, 10:32 PM

Quote:

Originally Posted by SIKH335

Ok guys quick update the car is heading to FFtec to pull the trans and is being shipped out to Sam @ 517Trans. Lets keep our fingers crossed Sam seems very knowledgable and confident that his rebuild and upgrade will hold my Single Turbos power. If all goes well I will be all over the 60-130 numbers right away and will make my way to Sacramento for some 1/4 mile runs. Fingers crossed!!!!

SIKH335 · 02-12-2013, 11:27 PM

Quote:

Originally Posted by Dmacc

Quote:

Originally Posted by SIKH335

Ok guys quick update the car is heading to FFtec to pull the trans and is being shipped out to Sam @ 517Trans. Lets keep our fingers crossed Sam seems very knowledgable and confident that his rebuild and upgrade will hold my Single Turbos power. If all goes well I will be all over the 60-130 numbers right away and will make my way to Sacramento for some 1/4 mile runs. Fingers crossed!!!!

Good luck! Your car is going to be scary fast! This means you'll be able to up your boost to MT single turbo guys correct?

Partially correct. I will be able to turn the boost up however due to the rev limit difference between the 6AT and 6MT I won't have the same peak power. Essentially the same power curve up to the 6AT redline the 6MT continues for an additional 50whp. But fast either way and I will be able to finally test the car which no 6AT single has been able to do yet.

Dmacc · 02-13-2013, 12:04 AM

Quote:

Originally Posted by SIKH335

Quote:

Originally Posted by Dmacc

Quote:

Originally Posted by SIKH335

Ok guys quick update the car is heading to FFtec to pull the trans and is being shipped out to Sam @ 517Trans. Lets keep our fingers crossed Sam seems very knowledgable and confident that his rebuild and upgrade will hold my Single Turbos power. If all goes well I will be all over the 60-130 numbers right away and will make my way to Sacramento for some 1/4 mile runs. Fingers crossed!!!!

Good luck! Your car is going to be scary fast! This means you'll be able to up your boost to MT single turbo guys correct?

Partially correct. I will be able to turn the boost up however due to the rev limit difference between the 6AT and 6MT I won't have the same peak power. Essentially the same power curve up to the 6AT redline the 6MT continues for an additional 50whp. But fast either way and I will be able to finally test the car which no 6AT single has been able to do yet.

That will be FAST! I might need to get a ride in that once it's ready

sammy_0559 · 02-13-2013, 12:11 AM

Quote:

Originally Posted by SIKH335

Ok guys quick update the car is heading to FFtec to pull the trans and is being shipped out to Sam @ 517Trans. Lets keep our fingers crossed Sam seems very knowledgable and confident that his rebuild and upgrade will hold my Single Turbos power. If all goes well I will be all over the 60-130 numbers right away and will make my way to Sacramento for some 1/4 mile runs. Fingers crossed!!!!

FML i just shipped my parts to level 10

badass335 · 02-13-2013, 12:36 AM

That's awesome news man!! Can't wait! Might have to do a road trip out to check your ride out!

SIKH335 · 02-13-2013, 12:37 AM

Quote:

Originally Posted by sammy_0559

Quote:

Originally Posted by SIKH335

Ok guys quick update the car is heading to FFtec to pull the trans and is being shipped out to Sam @ 517Trans. Lets keep our fingers crossed Sam seems very knowledgable and confident that his rebuild and upgrade will hold my Single Turbos power. If all goes well I will be all over the 60-130 numbers right away and will make my way to Sacramento for some 1/4 mile runs. Fingers crossed!!!!

FML i just shipped my parts to level 10

Sammy aren't you just doing the Upgraded Valve Body and low stall Torque Converter? Will you be doing and OEM rebuild kit or Level 10. Mine is a full rebuild upgraded Clutch plates, VB,TQ Converter the whole deal. Either way we should have se great data to help everyone choose going forward.

Check the VB to see if its shimmed or if they have replaced the Springs when it gets back. That's one of the rumors is they Shim rather than actually using stiffer upgraded springs.

TT3 iN NyC · 02-13-2013, 01:49 PM

Quote:

Originally Posted by SIKH335

Sammy aren't you just doing the Upgraded Valve Body and low stall Torque Converter? Will you be doing and OEM rebuild kit or Level 10. Mine is a full rebuild upgraded Clutch plates, VB,TQ Converter the whole deal. Either way we should have se great data to help everyone choose going forward.

Check the VB to see if its shimmed or if they have replaced the Springs when it gets back. That's one of the rumors is they Shim rather than actually using stiffer upgraded springs.

Wow, this shop is only an hour and half away from me.

If they need a test car, i would've volunteered lol

trbolexis · 02-16-2013, 05:44 PM

Tada ...

SIKH335 · 02-17-2013, 12:36 AM

Quote:

Originally Posted by trbolexis

Tada ...

Sweet u guys got the Trans out and ready to ship. Thanks bro I can wait to get this back after the build.

SIKH335 · 02-17-2013, 09:35 PM

Keep posted Wedge and CN555ic have figured out how to flash the TCU with Alpina B3 software.

Wedge1967 · 02-17-2013, 11:22 PM

Flash works with some minor changes to the display. Shift point is 6800 rpm, quick and firm. Before it was soft and sloppy. Prior to upgrade, I have seen rev's shoot up into red line on shift. It would cause the throttle body to shut which is not good... As you can see in this video, at shift it quickly drops back to 5400 rpm and pulls hard again just like it should. Hope we can get this on a ST or RB car this week and see how things look after flash. Will be a good day for upgraded AT cars. For everyone else, I highly recommend flashing. I think you'll really like the Alpina flash. DIY will be uploaded soon. Special thanks to Cn555ic for all his help in getting this figured out. Couldn't have done it without.

TT3 iN NyC · 02-17-2013, 11:50 PM

Quote:

Originally Posted by Wedge1967

Flash works with some minor changes to the display. Shift point is 6800 rpm, quick and firm. Before it was soft and sloppy. Prior to upgrade, I have seen rev's shoot up into red line on shift. It would cause the throttle body to shut which is not good... As you can see in this video, at shift it quickly drops back to 5400 rpm and pulls hard again just like it should. Hope we can get this on a ST or RB car this week and see how things look after flash. Will be a good day for upgraded AT cars. For everyone else, I highly recommend flashing. I think you'll really like the Alpina flash. DIY will be uploaded soon. Special thanks to Cn555ic for all his help in getting this figured out. Couldn't have done it without.

This is awesome!!!

Wedge1967 · 02-18-2013, 12:05 AM

Quote:

Originally Posted by TT3 iN NyC

This is awesome!!!

Wish I was in Map4 with Meth. Pulls a lot harder. Just too cold. But the shift is spot on.

cookiesowns · 02-18-2013, 12:20 AM

Quote:

Originally Posted by Wedge1967

Flash works with some minor changes to the display. Shift point is 6800 rpm, quick and firm. Before it was soft and sloppy. Prior to upgrade, I have seen rev's shoot up into red line on shift. It would cause the throttle body to shut which is not good... As you can see in this video, at shift it quickly drops back to 5400 rpm and pulls hard again just like it should. Hope we can get this on a ST or RB car this week and see how things look after flash. Will be a good day for upgraded AT cars. For everyone else, I highly recommend flashing. I think you'll really like the Alpina flash. DIY will be uploaded soon. Special thanks to Cn555ic for all his help in getting this figured out. Couldn't have done it without.

Awesome stuff!

If only the E9X AT guys have the same option as the "SAT" on the E60s. Hit the sport button and it shifts hard, fast, and firm, without the sport button, everything is tame. Also add in rev-matching as well!

Wedge1967 · 02-18-2013, 12:34 AM

Quote:

Originally Posted by cookiesowns

Awesome stuff!

If only the E9X AT guys have the same option as the "SAT" on the E60s. Hit the sport button and it shifts hard, fast, and firm, without the sport button, everything is tame. Also add in rev-matching as well!

Well, it's kinda like that. D is silky smooth, S is firmer and quicker shifts, and M is crisp and spot on. Get the DIY, cable and software. It's no sport button, but will be much nicer if you have the paddles. Not sure how it will work on cars without paddles installed.

enrita · 02-18-2013, 01:23 AM

Quote:

Originally Posted by Wedge1967

Well, it's kinda like that. D is silky smooth, S is firmer and quicker shifts, and M is crisp and spot on. Get the DIY, cable and software. It's no sport button, but will be much nicer if you have the paddles. Not sure how it will work on cars without paddles installed.

apparently you need the paddles to run this flash. its coded to have it.

sammy_0559 · 02-18-2013, 01:32 AM

Quote:

Originally Posted by enrita

nobody can flash the TCU as of now besides probably ALPINA or ZF engineers . Lots of people would have already done it if it was possible. I know only 1 person that flashed the TCU and it was done by Alpina in Germany for a ridiculous amount of money and only because he had contacts.
So forget about TCU or fitting another type of transmission. Rebuild what you have is the only option.

you can edit your comment now

enrita · 02-18-2013, 01:56 AM

Quote:

Originally Posted by sammy_0559

you can edit your comment now

:happy anim:

iDriveSlo · 02-18-2013, 02:02 AM

Wait so how do we obtain this? and what are we looking at for cost from alpina for the TCU flash?

eriktufa · 02-18-2013, 02:11 AM

Ok excited now

02-12-2013, 10:06 PM	#45
SIKH335 Banned 29 Rep 969 Posts Drives: 2007 335i Coupe Join Date: May 2011 Location: SF Bay Area iTrader: (6) Garage List 2007 E92 335i [1.00]	Ok guys quick update the car is heading to FFtec to pull the trans and is being shipped out to Sam @ 517Trans. Lets keep our fingers crossed Sam seems very knowledgable and confident that his rebuild and upgrade will hold my Single Turbos power. If all goes well I will be all over the 60-130 numbers right away and will make my way to Sacramento for some 1/4 mile runs. Fingers crossed!!!!
	Appreciate 0 Quote

02-13-2013, 12:36 AM	#51
badass335 Lieutenant Colonel 109 Rep 1,948 Posts Drives: 2017 540i Xdrive Join Date: Jul 2007 Location: Surrey, BC iTrader: (10)	That's awesome news man!! Can't wait! Might have to do a road trip out to check your ride out!
	Appreciate 0 Quote

02-16-2013, 05:44 PM	#54
trbolexis Private 0 Rep 74 Posts Drives: Lexus IS300 Join Date: Sep 2012 Location: CA iTrader: (0)	Tada ...
	Appreciate 0 Quote

02-17-2013, 09:35 PM	#56
SIKH335 Banned 29 Rep 969 Posts Drives: 2007 335i Coupe Join Date: May 2011 Location: SF Bay Area iTrader: (6) Garage List 2007 E92 335i [1.00]	Keep posted Wedge and CN555ic have figured out how to flash the TCU with Alpina B3 software.
	Appreciate 0 Quote

02-17-2013, 11:22 PM	#57
Wedge1967 Banned 125 Rep 2,172 Posts Drives: '07 e92 AT Sport Montego Blue Join Date: Sep 2011 Location: Portland, OR iTrader: (3)	Flash works with some minor changes to the display. Shift point is 6800 rpm, quick and firm. Before it was soft and sloppy. Prior to upgrade, I have seen rev's shoot up into red line on shift. It would cause the throttle body to shut which is not good... As you can see in this video, at shift it quickly drops back to 5400 rpm and pulls hard again just like it should. Hope we can get this on a ST or RB car this week and see how things look after flash. Will be a good day for upgraded AT cars. For everyone else, I highly recommend flashing. I think you'll really like the Alpina flash. DIY will be uploaded soon. Special thanks to Cn555ic for all his help in getting this figured out. Couldn't have done it without.
	Appreciate 0 Quote

02-18-2013, 02:02 AM	#65
iDriveSlo Captain 39 Rep 689 Posts Drives: 335i Coupe M-Sport Lemans blue Join Date: Sep 2012 Location: United States iTrader: (1) Garage List 2009 335i M-Sport [0.00]	Wait so how do we obtain this? and what are we looking at for cost from alpina for the TCU flash? __________________ 2009 E92 M-Sport 6AT PTF Pro Tune Vargas Stage 2
	Appreciate 0 Quote

02-18-2013, 02:11 AM	#66
eriktufa 3r1k 30 Rep 360 Posts Drives: 2008 MY08 BMW E92 335i Join Date: Jan 2012 Location: Perth iTrader: (0)	Ok excited now __________________ 12.836 @ 109.75mph (Cobb - Accessport & VRSF DP)
	Appreciate 0 Quote