Can't activate Bluetooth E92 with MULF, 6FL, and 2URAD

veloearl · 06-23-2012, 07:59 PM

I have a June 2010 E92 with the Professional Stereo, USB/Aux interface, and BT-capable MULF in the trunk. Trying the BT retrofit. Read everything I could find.

Bought cable, downloaded software, updated Daten to v45.

Added $644 to the VO and did FA_WRITE to CAS and NFRM. Subsequently, when I access the VO, it shows this option listed.

Tried to activate the three Bluetooth values mentioned in the various threads, but my car has a 2URAD instead of a 2RAD. Reading that module results in an error. Tried activating the values anyway, as they were present in the resulting .TRC file that was created. Changed them to aktiv, saved it as .MAN, but writing the module results in an error.

I have tried both Expertmode, and Revtor's NCS Export profiles with same results.

I have seen that this error is common with 2URAD, and that adding $644 to the VO is enough; no additional coding required. However, that doesn't seem to be the case for my car. After letting the car sleep (as much as an hour), when I turn it on, no TEL option is present when pressing the Menu button on the stereo.

I haven't done any of the wiring yet, because I wanted to confirm I could active the feature before going any further. My understanding is that is OK

Any ideas?

Technic · 06-23-2012, 09:28 PM

Quote:

Originally Posted by veloearl

I have a June 2010 E92 with the Professional Stereo, USB/Aux interface, and BT-capable MULF in the trunk. Trying the BT retrofit. Read everything I could find.

Bought cable, downloaded software, updated Daten to v45.

Added $644 to the VO and did FA_WRITE to CAS and NFRM. Subsequently, when I access the VO, it shows this option listed.

Tried to activate the three Bluetooth values mentioned in the various threads, but my car has a 2URAD instead of a 2RAD. Reading that module results in an error. Tried activating the values anyway, as they were present in the resulting .TRC file that was created. Changed them to aktiv, saved it as .MAN, but writing the module results in an error.

I have tried both Expertmode, and Revtor's NCS Export profiles with same results.

I have seen that this error is common with 2URAD, and that adding $644 to the VO is enough; no additional coding required. However, that doesn't seem to be the case for my car. After letting the car sleep (as much as an hour), when I turn it on, no TEL option is present when pressing the Menu button on the stereo.

I haven't done any of the wiring yet, because I wanted to confirm I could active the feature before going any further. My understanding is that is OK

Any ideas?

This has been discussed here before: you need a different (and much more expensive) OBDII cable to code the 2URAD.

pnickisson · 06-24-2012, 05:16 AM

have you written ablank .man file to the radio. I ddi this lst week..Added the options to the vo...both cas and nfrm....this did nothing I could see....then wrote a blank .man file to to 2rad...hey presto...everything worked.

snoozee · 06-24-2012, 06:55 AM

the BT retrofit requires the radio to be coded and it doesn't matter if the hardware (bt antenna & mic) is there or not as long as the mulf2 is there.

see if you can read the 2URAD using tool32. if you can, try to reset the module via tool32 and see if it works.

another alternative to buying the much more expensive icom OPS head is to search hard for the icom emulator. up till about 1 month ago, this icom emulator is only available if you bought it from the developet/programmer/hacker. however it has since been shared on other forums. search for ista-d 2.30 on google and you should be able to find the forum for you to download it. this should allow you to use the newer software (different from NCS) to code the car properly via the OBD cable.

bmw325i · 06-24-2012, 01:05 PM

I coded 2urad with a regular k-can cable. I really don't think the cable is the problem.

veloearl · 06-24-2012, 02:14 PM

I got it working. I only wish I knew exactly what it was that fixed it. Last thing I tried was coding the whole car with revtor's NCS Expert profile, letting it sleep, then voila, the phone option was there.

Hooked up the antenna and microphone. Everything is working; contacts synchronize, incoming audio is perfect.

Problem is, the outgoing audio is unusable. If I speak directly into the microphone, it sounds fine. If I speak from the standard driver's position, it sounds very distant and cuts out. I have no idea what the problem is.

Any ideas?

Technic · 06-24-2012, 03:15 PM

Quote:

Originally Posted by bmw325i

I coded 2urad without a regular k-can cable. I really don't think the cable is the problem.

If you radio is before 2010 then it will code with the regular cable without problems.

JimVR4 · 06-26-2012, 02:52 PM

Quote:

Originally Posted by bmw325i

I coded 2urad with a regular k-can cable. I really don't think the cable is the problem.

Quote:

Originally Posted by Technic

If you radio is before 2010 then it will code with the regular cable without problems.

I would like to hear how you coded 2URAD. I never could read the module with a K-DCAN cable with NCS Expert or Tool32. My car is a 2009 E90.

Bimmer-Bob · 06-27-2012, 11:58 AM

Are there any vendors that sell an off the shelf BT retrofit kit and/or any shops that routinely do the install/coding? I don't really have the time to figure it all out on my own (the coding especially). If it makes a difference, I've got a 2010 1er with USB/iPod and a box in the trunk with the BT logo (is this the MULF?).

Thanks.

Technic · 06-27-2012, 12:38 PM

Quote:

Originally Posted by Bimmer-Bob

Are there any vendors that sell an off the shelf BT retrofit kit and/or any shops that routinely do the install/coding? I don't really have the time to figure it all out on my own (the coding especially). If it makes a difference, I've got a 2010 1er with USB/iPod and a box in the trunk with the BT logo (is this the MULF?).

Thanks.

Contact forum vendor BimmerTech...

Bimmer-Bob · 06-27-2012, 01:05 PM

Quote:

Originally Posted by Technic

Quote:

Originally Posted by Bimmer-Bob

Are there any vendors that sell an off the shelf BT retrofit kit and/or any shops that routinely do the install/coding? I don't really have the time to figure it all out on my own (the coding especially). If it makes a difference, I've got a 2010 1er with USB/iPod and a box in the trunk with the BT logo (is this the MULF?).

Thanks.

Contact forum vendor BimmerTech...

Thanks!

alexwhittemore · 10-08-2012, 01:33 AM

Quote:

Originally Posted by JimVR4

I would like to hear how you coded 2URAD. I never could read the module with a K-DCAN cable with NCS Expert or Tool32. My car is a 2009 E90.

I hate to resurrect a thread, but I'm in the same spot now. Anybody ever resolve this? I'm not actually sure how to figure out how to try resetting the unit in Tool32, so if anyone has pointers on what to try there, I'm open. Really, I'd love to be able to write a config though.

alexwhittemore · 11-01-2012, 08:08 PM

Bump: Snoozee suggested trying to reset the 2URAD with tool32. I didn't use tool32, but there's an SG_RESET job in ncsexpert that worked for me - radio reset as expected. But the bluetooth option didn't show up. I haven't tried writing a BLANK .man file via revtor profile, but people seem to treat doing that like it's very scary, so I'm kind of loathe to do so. I also haven't seen anything about how it can go wrong, it all seems like superstition that it's especially dangerous.

studeezy · 12-17-2012, 10:58 PM

Alex, did you ever get it working? I'm having the same problem. I added $644 to the VO but my radio isn't picking it up, and I can't code it directly because I don't have the optical connection. SG_Reset worked but didn't enable bluetooth.

*Edit: Nvm, i found your post "http://www.e90post.com/forums/showthread.php?t=765036" I will try doing what you said in the morning.

alexwhittemore · 12-17-2012, 11:06 PM

Yep. For one, you need to add $644 to the VO in BOTH N/FRM and CAS. After you have, you must SG_RESET BOTH the 2URAD and MULF, but even that didn't work for me: I ended up needing to run the SG_RESET on all modules together.

studeezy · 12-18-2012, 11:17 AM

Ok so i finally got it working. I found an entry in the MAN file that said Bluetooth nicht_aktiv. I changed it to aktiv then coded the whole car, the 2URAD and ULF didnt respond...which was expected. After that I did an SG reset on the 2URAD and left it overnight. This morning i had a phone icon and was able to pair my phone and make a test call.

alexwhittemore · 12-18-2012, 11:20 AM

For the record, setting Bluetooth aktiv was almost certainly irrelevant. For one, it didn't get coded to the 2urad, but for two, even if you can successfully write the radio, manually forcing BT aktiv has been shown before to be kind of unstable - the phone icon will show up, but USB will stop working and you may or may not be able to pair.

Anyway, glad you got it working!

studeezy · 12-18-2012, 11:31 AM

Figured..I wasn't really sure if setting the Bluetooth to aktiv even did anything
Luckily USB still works and pairing works. Thnx for the tip.

06-23-2012, 07:59 PM	#1
veloearl New Member 3 Rep 8 Posts Drives: 328i Join Date: May 2012 Location: Steamboat Springs iTrader: (0)	Can't activate Bluetooth E92 with MULF, 6FL, and 2URAD I have a June 2010 E92 with the Professional Stereo, USB/Aux interface, and BT-capable MULF in the trunk. Trying the BT retrofit. Read everything I could find. Bought cable, downloaded software, updated Daten to v45. Added $644 to the VO and did FA_WRITE to CAS and NFRM. Subsequently, when I access the VO, it shows this option listed. Tried to activate the three Bluetooth values mentioned in the various threads, but my car has a 2URAD instead of a 2RAD. Reading that module results in an error. Tried activating the values anyway, as they were present in the resulting .TRC file that was created. Changed them to aktiv, saved it as .MAN, but writing the module results in an error. I have tried both Expertmode, and Revtor's NCS Export profiles with same results. I have seen that this error is common with 2URAD, and that adding $644 to the VO is enough; no additional coding required. However, that doesn't seem to be the case for my car. After letting the car sleep (as much as an hour), when I turn it on, no TEL option is present when pressing the Menu button on the stereo. I haven't done any of the wiring yet, because I wanted to confirm I could active the feature before going any further. My understanding is that is OK Any ideas?
	Appreciate 0 Tweet Quote

06-24-2012, 05:16 AM	#3
pnickisson New Member 0 Rep 8 Posts Drives: 330d M Sport Join Date: Oct 2011 Location: Manchester iTrader: (0)	have you written ablank .man file to the radio. I ddi this lst week..Added the options to the vo...both cas and nfrm....this did nothing I could see....then wrote a blank .man file to to 2rad...hey presto...everything worked.
	Appreciate 0 Quote

06-24-2012, 06:55 AM	#4
snoozee Second Lieutenant 4 Rep 213 Posts Drives: 318i Join Date: Mar 2012 Location: Singapore iTrader: (0)	the BT retrofit requires the radio to be coded and it doesn't matter if the hardware (bt antenna & mic) is there or not as long as the mulf2 is there. see if you can read the 2URAD using tool32. if you can, try to reset the module via tool32 and see if it works. another alternative to buying the much more expensive icom OPS head is to search hard for the icom emulator. up till about 1 month ago, this icom emulator is only available if you bought it from the developet/programmer/hacker. however it has since been shared on other forums. search for ista-d 2.30 on google and you should be able to find the forum for you to download it. this should allow you to use the newer software (different from NCS) to code the car properly via the OBD cable.
	Appreciate 0 Quote

06-24-2012, 01:05 PM	#5
bmw325i Major General 223 Rep 5,120 Posts Drives: 2006 BMW 325i Join Date: Oct 2010 Location: United States iTrader: (8)	I coded 2urad with a regular k-can cable. I really don't think the cable is the problem.
	Appreciate 0 Quote

06-24-2012, 02:14 PM	#6
veloearl New Member 3 Rep 8 Posts Drives: 328i Join Date: May 2012 Location: Steamboat Springs iTrader: (0)	I got it working. I only wish I knew exactly what it was that fixed it. Last thing I tried was coding the whole car with revtor's NCS Expert profile, letting it sleep, then voila, the phone option was there. Hooked up the antenna and microphone. Everything is working; contacts synchronize, incoming audio is perfect. Problem is, the outgoing audio is unusable. If I speak directly into the microphone, it sounds fine. If I speak from the standard driver's position, it sounds very distant and cuts out. I have no idea what the problem is. Any ideas?
	Appreciate 0 Quote

06-27-2012, 11:58 AM	#9
Bimmer-Bob ! 693 Rep 3,266 Posts Drives: 2010 128i Join Date: Feb 2010 Location: Anacortes, WA iTrader: (4) Garage List 2010 BMW 128i (E82) [9.25]	Are there any vendors that sell an off the shelf BT retrofit kit and/or any shops that routinely do the install/coding? I don't really have the time to figure it all out on my own (the coding especially). If it makes a difference, I've got a 2010 1er with USB/iPod and a box in the trunk with the BT logo (is this the MULF?). Thanks. __________________ ____________________________ My Build Thread
	Appreciate 0 Quote

11-01-2012, 08:08 PM	#13
alexwhittemore Lieutenant Colonel 111 Rep 1,951 Posts Drives: 2009 Crimson 328i Join Date: Oct 2012 Location: Los Angeles iTrader: (0)	Bump: Snoozee suggested trying to reset the 2URAD with tool32. I didn't use tool32, but there's an SG_RESET job in ncsexpert that worked for me - radio reset as expected. But the bluetooth option didn't show up. I haven't tried writing a BLANK .man file via revtor profile, but people seem to treat doing that like it's very scary, so I'm kind of loathe to do so. I also haven't seen anything about how it can go wrong, it all seems like superstition that it's especially dangerous.
	Appreciate 0 Quote

12-17-2012, 10:58 PM	#14
studeezy Private 4 Rep 59 Posts Drives: 2015 M4 Join Date: Dec 2012 Location: FL iTrader: (1)	Alex, did you ever get it working? I'm having the same problem. I added $644 to the VO but my radio isn't picking it up, and I can't code it directly because I don't have the optical connection. SG_Reset worked but didn't enable bluetooth. Edit: Nvm, i found your post "http://www.e90post.com/forums/showthread.php?t=765036" I will try doing what you said in the morning. Last edited by studeezy; 12-17-2012 at 11:22 PM..*
	Appreciate 0 Quote

12-17-2012, 11:06 PM	#15
alexwhittemore Lieutenant Colonel 111 Rep 1,951 Posts Drives: 2009 Crimson 328i Join Date: Oct 2012 Location: Los Angeles iTrader: (0)	Yep. For one, you need to add $644 to the VO in BOTH N/FRM and CAS. After you have, you must SG_RESET BOTH the 2URAD and MULF, but even that didn't work for me: I ended up needing to run the SG_RESET on all modules together.
	Appreciate 0 Quote

12-18-2012, 11:17 AM	#16
studeezy Private 4 Rep 59 Posts Drives: 2015 M4 Join Date: Dec 2012 Location: FL iTrader: (1)	Ok so i finally got it working. I found an entry in the MAN file that said Bluetooth nicht_aktiv. I changed it to aktiv then coded the whole car, the 2URAD and ULF didnt respond...which was expected. After that I did an SG reset on the 2URAD and left it overnight. This morning i had a phone icon and was able to pair my phone and make a test call.
	Appreciate 0 Quote

12-18-2012, 11:20 AM	#17
alexwhittemore Lieutenant Colonel 111 Rep 1,951 Posts Drives: 2009 Crimson 328i Join Date: Oct 2012 Location: Los Angeles iTrader: (0)	For the record, setting Bluetooth aktiv was almost certainly irrelevant. For one, it didn't get coded to the 2urad, but for two, even if you can successfully write the radio, manually forcing BT aktiv has been shown before to be kind of unstable - the phone icon will show up, but USB will stop working and you may or may not be able to pair. Anyway, glad you got it working!
	Appreciate 0 Quote

12-18-2012, 11:31 AM	#18
studeezy Private 4 Rep 59 Posts Drives: 2015 M4 Join Date: Dec 2012 Location: FL iTrader: (1)	Figured..I wasn't really sure if setting the Bluetooth to aktiv even did anything Luckily USB still works and pairing works. Thnx for the tip.
	Appreciate 0 Quote