[paapaa]

Originally Posted by Simon76

No No.
When i click on the link provided by Robb, http://www.cobbtuning.com/BMW-Access...s/bmw/bmw-grid
there are blue ecu-icons.
And no red BETA button.
I have tried a hundred times. Starting on there homepage, or clicking the link above.
No matter i have the direct link, but it´s very strange..

then it must be your web browser color/link settings...reset all browser setting to default or change to IE-Firefox-or else and you´ll see the link.

[Simon76]

I installed Firefox, now i can see it

[woosh]

Originally Posted by adidasoccer

just tested the maps jason sent me and the problems all worked out enjoying the smoother map and the outstanding service thanks

Well done COBB

[2Times]

I have a dumb question... but how would Stage2 Aggressive compare to Stage2+ sport? Would the aggressive map just have greater timing while the 2+ have more boost?

[Jblaze4lif]

Just browsing the beta section I dont have a cobb accessport yet. How do you know which ecu type you have. When you have a cobb and want to dl a new map to it what do you just plug it into computer dl the map And then what?

[rader1]

The AP and AP manager will tell you what DME version you have. You plug the AP into your computer, download the map, transfer it to your AP using the AP manager and then plug the AP into the car and select "change tune" and pick the map you just downloaded.

[vasillalov]

Team Cobb,

How are you guys calculating torque output in your v4 maps? Here is a log from a short pull I did the other day and it looks like the car is putting down 788 Nm of torque (581 ft/lbs)

[Hierlevelz]

My car threw the following code this morning:

P2D59 - DME, internal error: monitoring actual torque

I was cruising along in forth at ~3000rpm.
I was currently running the v4 stg1 aggressive linear map.

Application
2009 335i MT
IJE0S ecu

I am guessing this issue has to be resolved in the beta maps?
Was the issue ever resolved in the prior versions?
I switched back to the v3.01 map and hopefully I wont have any issues.

[rader1]

I think that issue pops up in beta maps on occasion, I haven't seen it but it seems that whenever beta maps are released a few people see it. Email Cobb and see what they say.

[2Times]

Flashing v400 map now. I was thinking that it was only going to take 2 minutes but its doing the long flash and I've been here for about 15 minutes at 61%

[Velocity26]

I have timed my map switches before and my car was always slow (about 90 seconds) but switching to my first V400 just took about 10 minutes. It took almost 2 minutes to get to 1%. There was lots of activity in the beginning, long quiet period in the middle, and then lots of stuff nearing the end.

Never heard Rob comment on the amount of time to change maps being so variable. I also kept my charger attached, just in case.

[Rob@Cobb]

Originally Posted by Hierlevelz

My car threw the following code this morning:

P2D59 - DME, internal error: monitoring actual torque

I was cruising along in forth at ~3000rpm.
I was currently running the v4 stg1 aggressive linear map.

Application
2009 335i MT
IJE0S ecu

I am guessing this issue has to be resolved in the beta maps?
Was the issue ever resolved in the prior versions?
I switched back to the v3.01 map and hopefully I wont have any issues.

It is an issue we are aware of and addressing. If you would be so kind as to email me, I can get you a revised map to try.

Cheers,
rob\at/cobbtuning|com

[Rob@Cobb]

Originally Posted by Velocity26

I have timed my map switches before and my car was always slow (about 90 seconds) but switching to my first V400 just took about 10 minutes. It took almost 2 minutes to get to 1%. There was lots of activity in the beginning, long quiet period in the middle, and then lots of stuff nearing the end.

Never heard Rob comment on the amount of time to change maps being so variable. I also kept my charger attached, just in case.

The flash time depends on what is changed in the mapping. When we make bigger changes the mapping, it takes longer. Say we put out a revised v401 mapping, it should only take 1 min or so to change maps.

Cheers,
Rob

[Rob@Cobb]

Originally Posted by vasillalov

Team Cobb,

How are you guys calculating torque output in your v4 maps? Here is a log from a short pull I did the other day and it looks like the car is putting down 788 Nm of torque (581 ft/lbs)

Hehe, it's the ECUs internal calculation that is not entirely accurate at that stage.

Cheers,
Rob

[Hierlevelz]

Originally Posted by Rob@Cobb

It is an issue we are aware of and addressing. If you would be so kind as to email me, I can get you a revised map to try.

Cheers,
rob\at/cobbtuning|com

bump for rob....he sent me a revised map I will try it out and report back. Has any done a dyno and or log of any of these maps?

[adidasoccer]

Originally Posted by Hierlevelz

My car threw the following code this morning:

P2D59 - DME, internal error: monitoring actual torque

I was cruising along in forth at ~3000rpm.
I was currently running the v4 stg1 aggressive linear map.

Application
2009 335i MT
IJE0S ecu

I am guessing this issue has to be resolved in the beta maps?
Was the issue ever resolved in the prior versions?
I switched back to the v3.01 map and hopefully I wont have any issues.

i had the same problem its a few pages back same ecu try re-flashing if that doesn't work contact cobb i got same day service and its working flawlessly... enjoy ur tune

[Velocity26]

Purely a "seat of the pants dyno" assessment but it feels as if the v400 maps bring a litle more to the table than the v301 versions. Anybody else noticing anything different?

[skinrock]

I've been having a rather interesting problem lately with shifting in DS on my auto. I am running Stage 2+FMIC Sport ST. I had a couple misfires a month ago, but switching my plugs fixed it.

This has happened in v301 and in the new v400 beta. Outside of this issue, it feels great, pulls strong and no codes.

So the issue is when I'm going about 40-50 mph and then I go wot, for example onto an expressway entrance ramp. The first time it happened I didn't pay too much attention, but it was basically screaming and not going anywhere, it felt like it didn't want to shift. Tonight, I paid closer attention, and sure enough - it hit about 7k rpm. I decided to shift with M mode, and then it started pulling a little more, but then it felt like it shifted again.

Unfortunately I don't have a log, but I'm not sure if that would tell us anything. I'm almost certain it shouldn't be hitting 7k, and it feels like crap at that rpm anyways. Has anyone else experienced this?

[themyst]

Originally Posted by skinrock

I've been having a rather interesting problem lately with shifting in DS on my auto. I am running Stage 2+FMIC Sport ST. I had a couple misfires a month ago, but switching my plugs fixed it.

This has happened in v301 and in the new v400 beta. Outside of this issue, it feels great, pulls strong and no codes.

So the issue is when I'm going about 40-50 mph and then I go wot, for example onto an expressway entrance ramp. The first time it happened I didn't pay too much attention, but it was basically screaming and not going anywhere, it felt like it didn't want to shift. Tonight, I paid closer attention, and sure enough - it hit about 7k rpm. I decided to shift with M mode, and then it started pulling a little more, but then it felt like it shifted again.

Unfortunately I don't have a log, but I'm not sure if that would tell us anything. I'm almost certain it shouldn't be hitting 7k, and it feels like crap at that rpm anyways. Has anyone else experienced this?

put "Torque Limit Active" in your logs. If the monitor shows "4" the ECU is cutting power.

[skinrock]

Originally Posted by themyst

put "Torque Limit Active" in your logs. If the monitor shows "4" the ECU is cutting power.

I'll do that, thanks. Without logs, is it possible to know why it's doing this - too aggressive of a map for the gas?

[Hierlevelz]

Originally Posted by adidasoccer

i had the same problem its a few pages back same ecu try re-flashing if that doesn't work contact cobb i got same day service and its working flawlessly... enjoy ur tune

Rob sent me a "revised" map which I installed. So far so good.

[Deadwrong]

I finally loaded v400 beta and I noticed the improved "smoothness" instantly...I also installed DCI's today and I don't know if the improved responsiveness is from the DCI's, the update or both...