New Brake rotor/pads - BMW 3-Series (E90 E92) Forum

cgnahc · 12-26-2008, 03:38 PM

Just installed this week. Parts from iRotors...the pads needs to get conditioned before they perform better.

Autobot · 12-27-2008, 12:56 PM

Interesting, do you have a link? Did you install front and rears?

cgnahc · 12-29-2008, 07:34 PM

Front and rears, rotor, pads, sensor. www.irotors.com

They are out of the rear pads (E90), but will ship when available (or credit this part if bought as a combo set). Ceramic pads in rear now, which added an extra $65 on the install.

A little squeek, but should stop after a "break-in" period....about 200 miles.

cgnahc · 12-29-2008, 07:41 PM

My rear brakes needed the service initially. The cost of doing the rear set at the dealer was even more than the cost of doing all four!!

1clean335i · 12-29-2008, 08:07 PM

iRotors doesnt have anything for the 335...

cgnahc · 12-29-2008, 10:59 PM

check as E90 or E92, i or xi. They are on holiday (phone recording) but they got back to my email same day. You may want to request them made special...since they specialize in rotors.

I think E90 still covers 335 (325, 328) ...contact them to make sure. 335 is turbo, but should be same brake system.

Autobot · 12-29-2008, 11:34 PM

Let us know how they brake in...

cgnahc · 12-31-2008, 02:40 PM

Beside the better feel of thicker pads, the braking grab feel has been slowly improving. Still some sqeeeeeeks during slow to very slow (5mph) braking. So far it's been a week with about 50 miles daily 1/2 street and 1/2 highway driving. I am still careful not to brake too hard to "glaze" the pads, which will make them sound even more. I've been dragging the brake well before where I anticipate to stop.

I can't wait to do some real performance driving on these!!

Do spacers affect the performance of brakes?? I don't have them, but is wondering.

cgnahc · 12-31-2008, 02:48 PM

One nice word about iRotors:

I found them through ebay, but called to place the order. The lady that took the order dropped ship them to me even though both the company and I are in CA and should have charged tax...plus they had freeeee shipping. The sensors (front & rear) they added was very inexpensive with the package.

I figure they make good rotors when I decided with them.

cgnahc · 12-31-2008, 03:29 PM

Notice the grove direction relative to rotation on the install. My brake install guy said the brake performance is better this way. I may have to research this a little bit.

cgnahc · 01-06-2009, 07:52 PM

So far so good. Very low incidence of sqeaks, but still present...not as loud. Still dragging the brake and taking it easy. Maybe another week until I go for the ABS and test distance. Getting more grippy, without being too grippy like OEMs.

AP Racing - Chris_B · 01-10-2009, 07:18 PM

Quote:

Originally Posted by cgnahc

So far so good. Very low incidence of sqeaks, but still present...not as loud. Still dragging the brake and taking it easy. Maybe another week until I go for the ABS and test distance. Getting more grippy, without being too grippy like OEMs.

Not sure which pads you have, but you may want to review the bed-in procedure with the manufacturer. If they are the Centric Posi-Quiets is see on the irotors web site, noise would be unusual as they are very mild pads. The "ceramic" compound has a lower friction coefficient when compared to semi-metallic pads, so nothing out of the ordinary there.

Also, taking it easy won't lay down a pad transfer layer onto the rotor that is necessary to get all the performance you paid for. A lot of times, depending on many factors (pad material, installation procedure, shims, rotor design, etc.), they will quiet down as well. All standard stuff, but YMMV.

cgnahc · 01-14-2009, 07:40 PM

louder squeaking during higher speed deceleration at around 30 mph with mid foot pressure. May need to bring it in.

cgnahc · 02-27-2009, 07:14 PM

squeal has not stopped...rotors fins need to be pointing backwards after talking to iRotors. Boo on my install guy...

The rear pads that was not shipped will be in stock 3/4/09.

AP Racing - Chris_B · 02-27-2009, 08:11 PM

Quote:

Originally Posted by cgnahc

squeal has not stopped...rotors fins need to be pointing backwards after talking to iRotors. Boo on my install guy...

The rear pads that was not shipped will be in stock 3/4/09.

That's an understandable installation error, but not acceptable. That said, I have seen more than one M3 over the years with rotors installed backwards from the factory. Monkey see, monkey do.

cgnahc · 03-02-2009, 02:04 PM

See that rotor pic is the rear right, and the fins are pointing forward (such that the outside hole/slot are entering the pads first). This rotor should be on the rear left. If I knew anything about the install, I would had said something, but I took it to a local brake service place thinking they could do this blind folded. Should have taken it to Longtran.

They did the switch and roughed up the pads and now, no squeek noise. Magic!

12-26-2008, 03:38 PM	#1
cgnahc Major Drives: TiAg E90 ZSP Join Date: Dec 2006 Location: Westlake Village, CA Posts: 1,258 iTrader: (9)	New Brake rotor/pads Just installed this week. Parts from iRotors...the pads needs to get conditioned before they perform better. Attached Images __________________ 9/2011 Need someone to install angle eye bulbs. 9/2011 WTB: an OEM 17" front rim.
	Tweet

12-27-2008, 12:56 PM	#2
Autobot Colonel Drives: 07 E90 Montego 6MT Join Date: Feb 2007 Location: Monterey, California Posts: 2,980 iTrader: (8) Garage List 06 325i [0.00] 07 328i [0.00]	Interesting, do you have a link? Did you install front and rears? __________________ MODS: Blacklines\|M6 Reps\|Rear Fog\|Silver CF Int Trim \|Silver CF Pedals, Dead Pedal & Brake hande\|OEM CF Trunk Spoiler \|ACS Roof Spoiler\|CF Mirror Covers\|CF Door Pillars \|8000K D1S\| Blue LED Interior Lights\|Black Grille\| LUX 5.0\| ACS front lip\| 20% Tint\| CF Roundels \| LED Turn signals \|Deleted Secondary Cats\|Eisenmann Race with mid-pipes\|BMW Perf SSK\| Black roof \| SWS 8 & PDX amp\|BMW Perf Fr Brakes \| Vorsteiner CF Hood

12-29-2008, 07:34 PM	#3
cgnahc Major Drives: TiAg E90 ZSP Join Date: Dec 2006 Location: Westlake Village, CA Posts: 1,258 iTrader: (9)	Front and rears, rotor, pads, sensor. www.irotors.com They are out of the rear pads (E90), but will ship when available (or credit this part if bought as a combo set). Ceramic pads in rear now, which added an extra $65 on the install. A little squeek, but should stop after a "break-in" period....about 200 miles. __________________ 9/2011 Need someone to install angle eye bulbs. 9/2011 WTB: an OEM 17" front rim.

12-29-2008, 07:41 PM	#4
cgnahc Major Drives: TiAg E90 ZSP Join Date: Dec 2006 Location: Westlake Village, CA Posts: 1,258 iTrader: (9)	My rear brakes needed the service initially. The cost of doing the rear set at the dealer was even more than the cost of doing all four!! __________________ 9/2011 Need someone to install angle eye bulbs. 9/2011 WTB: an OEM 17" front rim.

12-29-2008, 08:07 PM	#5
1clean335i Perf BMW mag issue 147, 159 Drives: Project Estoril Join Date: Feb 2007 Location: Central Florida Posts: 6,739 iTrader: (30) Garage List 2013 335i M-sport [0.00] 2011 X5 xdrive35i M ... [0.00] 2009 335i M-sport [0.00] 07' 335i Sedan [0.00]	iRotors doesnt have anything for the 335... __________________ '13 Estoril Blue 335i M-sport *Don't PM me!* Message me here- http://www.facebook.com/ProjectEstoril

12-29-2008, 10:59 PM	#6
cgnahc Major Drives: TiAg E90 ZSP Join Date: Dec 2006 Location: Westlake Village, CA Posts: 1,258 iTrader: (9)	check as E90 or E92, i or xi. They are on holiday (phone recording) but they got back to my email same day. You may want to request them made special...since they specialize in rotors. I think E90 still covers 335 (325, 328) ...contact them to make sure. 335 is turbo, but should be same brake system. __________________ 9/2011 Need someone to install angle eye bulbs. 9/2011 WTB: an OEM 17" front rim. Last edited by cgnahc; 12-31-2008 at 03:23 PM.

12-29-2008, 11:34 PM	#7
Autobot Colonel Drives: 07 E90 Montego 6MT Join Date: Feb 2007 Location: Monterey, California Posts: 2,980 iTrader: (8) Garage List 06 325i [0.00] 07 328i [0.00]	Let us know how they brake in... __________________ MODS: Blacklines\|M6 Reps\|Rear Fog\|Silver CF Int Trim \|Silver CF Pedals, Dead Pedal & Brake hande\|OEM CF Trunk Spoiler \|ACS Roof Spoiler\|CF Mirror Covers\|CF Door Pillars \|8000K D1S\| Blue LED Interior Lights\|Black Grille\| LUX 5.0\| ACS front lip\| 20% Tint\| CF Roundels \| LED Turn signals \|Deleted Secondary Cats\|Eisenmann Race with mid-pipes\|BMW Perf SSK\| Black roof \| SWS 8 & PDX amp\|BMW Perf Fr Brakes \| Vorsteiner CF Hood

12-31-2008, 02:40 PM	#8
cgnahc Major Drives: TiAg E90 ZSP Join Date: Dec 2006 Location: Westlake Village, CA Posts: 1,258 iTrader: (9)	Beside the better feel of thicker pads, the braking grab feel has been slowly improving. Still some sqeeeeeeks during slow to very slow (5mph) braking. So far it's been a week with about 50 miles daily 1/2 street and 1/2 highway driving. I am still careful not to brake too hard to "glaze" the pads, which will make them sound even more. I've been dragging the brake well before where I anticipate to stop. I can't wait to do some real performance driving on these!! Do spacers affect the performance of brakes?? I don't have them, but is wondering. __________________ 9/2011 Need someone to install angle eye bulbs. 9/2011 WTB: an OEM 17" front rim.

12-31-2008, 02:48 PM	#9
cgnahc Major Drives: TiAg E90 ZSP Join Date: Dec 2006 Location: Westlake Village, CA Posts: 1,258 iTrader: (9)	One nice word about iRotors: I found them through ebay, but called to place the order. The lady that took the order dropped ship them to me even though both the company and I are in CA and should have charged tax...plus they had freeeee shipping. The sensors (front & rear) they added was very inexpensive with the package. I figure they make good rotors when I decided with them. __________________ 9/2011 Need someone to install angle eye bulbs. 9/2011 WTB: an OEM 17" front rim. Last edited by cgnahc; 12-31-2008 at 03:23 PM.

12-31-2008, 03:29 PM	#10
cgnahc Major Drives: TiAg E90 ZSP Join Date: Dec 2006 Location: Westlake Village, CA Posts: 1,258 iTrader: (9)	Notice the grove direction relative to rotation on the install. My brake install guy said the brake performance is better this way. I may have to research this a little bit. __________________ 9/2011 Need someone to install angle eye bulbs. 9/2011 WTB: an OEM 17" front rim.

01-06-2009, 07:52 PM	#11
cgnahc Major Drives: TiAg E90 ZSP Join Date: Dec 2006 Location: Westlake Village, CA Posts: 1,258 iTrader: (9)	So far so good. Very low incidence of sqeaks, but still present...not as loud. Still dragging the brake and taking it easy. Maybe another week until I go for the ABS and test distance. Getting more grippy, without being too grippy like OEMs. __________________ 9/2011 Need someone to install angle eye bulbs. 9/2011 WTB: an OEM 17" front rim.

01-14-2009, 07:40 PM	#13
cgnahc Major Drives: TiAg E90 ZSP Join Date: Dec 2006 Location: Westlake Village, CA Posts: 1,258 iTrader: (9)	louder squeaking during higher speed deceleration at around 30 mph with mid foot pressure. May need to bring it in. __________________ 9/2011 Need someone to install angle eye bulbs. 9/2011 WTB: an OEM 17" front rim.

02-27-2009, 07:14 PM	#14
cgnahc Major Drives: TiAg E90 ZSP Join Date: Dec 2006 Location: Westlake Village, CA Posts: 1,258 iTrader: (9)	squeal has not stopped...rotors fins need to be pointing backwards after talking to iRotors. Boo on my install guy... The rear pads that was not shipped will be in stock 3/4/09. __________________ 9/2011 Need someone to install angle eye bulbs. 9/2011 WTB: an OEM 17" front rim.

03-02-2009, 02:04 PM	#16
cgnahc Major Drives: TiAg E90 ZSP Join Date: Dec 2006 Location: Westlake Village, CA Posts: 1,258 iTrader: (9)	See that rotor pic is the rear right, and the fins are pointing forward (such that the outside hole/slot are entering the pads first). This rotor should be on the rear left. If I knew anything about the install, I would had said something, but I took it to a local brake service place thinking they could do this blind folded. Should have taken it to Longtran. They did the switch and roughed up the pads and now, no squeek noise. Magic! __________________ 9/2011 Need someone to install angle eye bulbs. 9/2011 WTB: an OEM 17" front rim.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search