E90Post
 


TNT Racewerks
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Powertrain and Drivetrain Discussions > N54 Turbo Engine / Drivetrain / Exhaust Modifications - 335i > Bavarian Tech Code list



Reply
 
Thread Tools Search this Thread
      05-07-2009, 02:47 PM   #1
#1Stunna
Enlisted Member
 
#1Stunna's Avatar
 
Drives: '09 e92 m3, e92 335i
Join Date: Apr 2009
Location: Earth

Posts: 31
iTrader: (1)

Exclamation Bavarian Tech Code list

Here is my contribution to you guys. I have put this together before and figured you all should benefit from it also. Add as you wish.

Thanks

2F6C:
2F6C Exhaust fumeflap, input signal
Error will not cause a warning light
Error is currently present
Test conditions have been completed
Timeout
EXPLANATION: Unplugging actuator valve in trunk for added exhaust noise.
FIX: Plugging back in and clearing code.
*Code will not show up if you use the "golf tee mod"

2DEC:
2DEC Power management, battery control
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold
EXPLANATION: Installing JB+ while the car did not go into sleep mode.
FIX: Let car go into sleep mode, uninstall JB+ and reinstall it. Cleared code and never came back.
EXPLANATION: Disconnecting battery
FIX: Reconnect battery, clear and rescan.

2D18:
2D18 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION: Tuner detection code
FIX: Delete before service!

2D25C:
2D25 Mass Air Flow Excessive - External Tuning Box Detected
Error will not cause a warning light
Error is currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION: Tuner detection code
FIX: Delete before service!

2D1C
2D1C Accelerator pedal module, pedal sensor signal 2
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold
EXPLANATION: Gas pedal sensor or wiring issue
FIX:

2FBF:
2FBF Fuel Pressure at Injection Release
Error will not cause a warning light
Error is currently present
Short circuit or signal interruption
EXPLANATION: Fuel pump pressure code
FIX: Normally requires fuel pump replacement

2DED:
2DED Power management, standby current control
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: The closed circuit current momentarily exceeds its threshold value when the TCU wakes up to perform the "Stolen Vehicle Recovery" function. This should not cause a discharged battery.
FIX: Take to dealer.

2D5A
2D5A Control motor torque limitation
Error will not cause a warning light (it did cause a limp)
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

29DC:
29DC Cylinder injection switch-off
Error will cause a warning light
Error is not currently present
Test conditions have not been completed
Short circuit or signal interruption
EXPLANATION: Fuel pump code
FIX: Normally requires fuel pump replacement

2DC3:
2DC3 Control clamp 15
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Timeout
EXPLANATION:
FIX:

2E8D:
2E8D Intelligent battery sensor, signal transmission
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION: Small cable connected to battery has been removed
FIX:

2F8F:
2F8F Accelerator pedal module and brake pedal, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Burnout
FIX: Clear

29E2:
29E2 Fuel injection rail, pressure sensor signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION: Fuel pump code
FIX: Normally requires fuel pump replacement

2A80:
2A80 Inlet-Vanos variable cam control test, input signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX: Requires dealer service, not related to tuning

2A85:
2A85 Outlet-VANOS variable cam control test
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Timeout
EXPLANATION:
FIX: Requires dealer service, not related to tuning

2D58:
2D58 DME digital motor electronics, internal failure: control nominal torque?
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Timeout
EXPLANATION:
FIX:

2EE0:
2EE0 Coolant temperature sensor, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION:
FIX:

2A9A:
2A9A Camshaft sensor inlet, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

2ABC:
2ABC Charging pressure sensor, electrical
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: ECU lost connection with tune. Unplugging map sensor or tune with ECU awake will cause this
FIX: Clear code. If it comes back, check tune related wiring.

2ABD:
2ABD Intake pressure sensor, re-running
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: HPFP Failing?
FIX:Take care into dealer

2FBE:
2FBE Fuel pressure after motor stop
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Fuel pump code
FIX: Normally requires fuel pump replacement

2AAF
2AAF Fuel Pump Plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION: Fuel pump check.
FIX: Very common code stock and modified alike, does not trigger a CEL. Just ignore it.

2A17
2A17 DMTL diagnosis module tank leakage, system failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Timeout
EXPLANATION:
FIX:

2F0D:
2F0D Radiator blind, input signal, (GLF)

Error will not cause a warning light

Error is currently present

Test conditions have been completed

Timeout
EXPLANATION:
FIX:

30FE:
30FE Exhaust fume turbo charger, high pressure side
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Boost too high
FIX: Consult with your tuner.

30FF:
30FF, Exhaust fume turbocharger low side
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Boost under target
FIX: Check for boost leaks, and consult with your tuner.

30CF:
30CF Wastegate, input signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Wastegate physically unplugged.
FIX: Check wiring. Green and purple wires on JB3.

30D0:
30D0 Wastegate 2, input signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Wastegate physically unplugged.
FIX: Check wiring. Green and purple wires on JB3.

30F2:
30F2 Glow ignition: cylinder 6
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Super Knock in cylinder 6.
FIX: Excessive knock retard. Lower boost levels, or run higher octane.

30F1:
30F1 Glow ignition: cylinder 5
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Super Knock in cylinder 5.
FIX: Excessive knock retard. Lower boost levels, or run higher octane.

5088
Sensors gear selector switch
Error will not cause a warning light
Error is not currently present
Test conditions have not been completed
Timeout
EXPLANATION: Transmission switch did not respond in allowable time?????
FIX: Kick the shit out of the car and hope that it goes away

5DE1
DSC-ECU: ECU-internal: Clockstatus of the SP interface shows missing clock.
Error will not cause a warning light
Error is currently present
Test conditions have been completed
EXPLANATION: Codes from putting car on a dyno
FIX: Clear and rescan

5DE0
DSC-ECU: ECU-internal: Plausibility of the VASP-U_Bit versus Uz power supply_clamp_15.
Error will not cause a warning light
Error is currently present
Test conditions have been completed
EXPLANATION: Codes from putting car on a dyno
FIX: Clear and rescan

5E5B:
Stability control
Wheel speed sensor general: Long-term (several seconds) error suspicion of 3-4 RDF led to error mode.
Error will not cause a warning light
Error is not currently present
EXPLANATION: NO IDEA PLEASE HELP??? Yes I know it should have this since its on the main page.
FIX: Take to dealer?

5E40
5E40 Wheel speed sensor rear right: Signal edge missing(RDF-Typ11i).
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

5E1A
5E1A DSC-ECU: ECU-internal: Serial-Peripheral-Interface (SPI): Transmission failure multi IC.
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

51B0
51B0 DSC Signal not plausible: Brake pressure signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A559
Clamp 30g_f cutoff
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Pulled fuse out behind glovebox during tune install.
FIX: Make sure fuse is inserted. Clear and rescan.

A554
Alive telephone
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A0B0
A0B0 Ecu input brake lights
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION: Rear break bulb out.
FIX:Take to dealer to replace bulb or replace bulb on your own.

A375
A375 Communication with airbag ECU disturbed(Error_IBUS_CONNECTION_FAIL)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A092
A092 SHD Standardization 0xA092
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A3AD
A3AD CAN ID 1D0 error: Engine data
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A3AE
A3AE CAN ID 0AA error: Idle engine speed
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A8B6
A8B6 Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

A0B4
A0B4 Fault engine start starter
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

D356
D356 PT-CAN: Message TORQUE_3 (ID 0xAA) not received or wrong message length (DLC). [transmitter: DME]
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

D355
D355 PT-CAN: Message TORQUE_2 (ID 0x0A9) not received or wrong message length (DLC). [transmitter: DME]
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

D354
D354 PT-CAN: Message TORQUE_1 (ID 0xA8) not received or wrong message length (DLC). [transmitter: DME]
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

D904
D904 K CAN wire error
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

E717
E717 CAN message: Dates of engine
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

E71A
E71A CAN message: Torque 3
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

3100:
3100 boost-pressure control, deactivation
Error will not cause warning light
Error is not currently present
Test conditions have been completed.
EXPLANATION: This code is triggered any time you experience a 'limp' mode.
FIX: This code itself is meaningless and serves only to let you know a 'limp mode' took place.

2AD0:
2AD0 Gear Control
Error will not cause a warning light
Error is currently present
Test conditions have been completed
EXPLANATION: This code is usually triggered simultaneously with the code CF33.
It means that the transmission is in safe mode which may happen if engine module
is replaced or the engine adaptation values are reset.
FIX: Reset the transmission adaptation/learning values.

CF33:
Messages from engine control unit doesn't exist
Error will cause a warning light
Error is currently present
Test conditions have been completed
EXPLANATION: The transmission is in safe mode which may happen if
engine module is replaced or the engine adaptation values are reset.
FIX: Reset the transmission adaptation/learning values.

29D2
29D2 Misfirings, cylinder 6
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION:
FIX:

29D9
29D9 Misfirings in case of tank filling level too low
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold
EXPLANATION:
FIX:

29D1
29D1 Misfirings, cylinder 5
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION:
FIX:

A127
Error ACK clamp 15 off before request
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION:
FIX:

6140
Redundance comparison driver steering angle high
Error will cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

2F9E: Termic oil level sensor
Error will not cause a warning light
EXPLANATION: Low Level Warning
FIX: Change and/or add your oil. Take to dealer if you need to.

2A96:
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption
EXPLANATION:
FIX:

2DC5:
2DC5 Torque requirement via CAN controller area network, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

51A6:
Error engine signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold
EXPLANATION:
FIX:

E18C
Device didn't accept or confirm monitoring message (Error_Monitoring)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

E18F
Central registry does not match with debit configuration (Error_Registry_New)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
EXPLANATION:
FIX:

Last edited by #1Stunna; 05-07-2009 at 05:39 PM.
#1Stunna is offline  
0
Reply With Quote
      05-07-2009, 02:55 PM   #2
ThorsHammer
Major
 
ThorsHammer's Avatar
 
Drives: '09 BMW 335i Coupe
Join Date: Jan 2009
Location: San Antonio, TX

Posts: 1,389
iTrader: (10)

STICKY. PLEASE. Or put it in the DIY section.
__________________
"SYONRA" is for sale! http://www.e90post.com/forums/showthread.php?t=366678 BSM '09 e92 335i | Performance: JB3, RR Catted DP's, INJEN DCI, Britalman Exhst, AA FMIC, FORGE DVs | Suspension: ST-V1 Coils, Hotchkis Chassis Brace & F/R Sways | Wheels: Bremmer Kraft BR03s, Brake Performance Rotors, Cool Carbon Pads, ECS Lines | Exterior: OEM Aero Lip/Rear, ****** CF Trunk Lid, BLUX5 Angels, M-Force M3 Sides | Interior: Passport 9500ci, Black Trim, M3 Wheel
ThorsHammer is offline   United_States
0
Reply With Quote
      05-07-2009, 03:42 PM   #3
cincy335i
Lieutenant
 
cincy335i's Avatar
 
Drives: '08 Black Saph 335i coupe 6mt
Join Date: Mar 2009
Location: Cincinnati, Ohio

Posts: 418
iTrader: (0)

That is great...thank you for this!!!
cincy335i is offline  
0
Reply With Quote
      05-07-2009, 03:42 PM   #4
veightkiller
Brigadier General
 
veightkiller's Avatar
 
Drives: e90 335i
Join Date: Dec 2007
Location: Vancouver,B.C

Posts: 4,154
iTrader: (3)

good info!
veightkiller is offline   Canada
0
Reply With Quote
      05-07-2009, 03:46 PM   #5
jpsimon
Team Zissou
 
jpsimon's Avatar
 
Drives: 2015 STi
Join Date: Dec 2006
Location: CT

Posts: 9,015
iTrader: (5)

I don't think I see 2F9E on your list


2F9E: Termic oil level sensor
Error will not cause a warning light


I'm think (see: not 100% sure) this shows up if you get a "low oil" warning
__________________
2015 STi / 335xi (solid)
www.datazap.me - fast, free, interactive data log viewing

jpsimon is offline   United_States
0
Reply With Quote
      05-07-2009, 04:40 PM   #6
cocoturkey
Lieutenant
 
Drives: 08' e92 335i
Join Date: Jan 2008
Location: Taipei

Posts: 441
iTrader: (0)

my contribution to the list

29D2
29D2 Misfirings, cylinder 6
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
29D9
29D9 Misfirings in case of tank filling level too low
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold

________________________________________
29D1
29D1 Misfirings, cylinder 5
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________


A127
Error ACK clamp 15 off before request
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________


6140
Redundance comparison driver steering angle high
Error will cause a warning light
Error is not currently present
Test conditions have been completed
cocoturkey is offline   Taiwan
0
Reply With Quote
      05-07-2009, 04:56 PM   #7
#1Stunna
Enlisted Member
 
#1Stunna's Avatar
 
Drives: '09 e92 m3, e92 335i
Join Date: Apr 2009
Location: Earth

Posts: 31
iTrader: (1)

All added thank you for your contribution
#1Stunna is offline  
0
Reply With Quote
      05-07-2009, 05:08 PM   #8
cincy335i
Lieutenant
 
cincy335i's Avatar
 
Drives: '08 Black Saph 335i coupe 6mt
Join Date: Mar 2009
Location: Cincinnati, Ohio

Posts: 418
iTrader: (0)

Thanks for all of your efforts on this, it is really helpful. This must have taken a lot of time and effort and I think that it is really helpful. Thanks again. Cheers!
cincy335i is offline  
0
Reply With Quote
      05-07-2009, 05:12 PM   #9
Italia335i
Banned
 
Drives: BMW
Join Date: Mar 2009
Location: USA

Posts: 88
iTrader: (1)

lol....Delta at least say who you really are.

The OP is delta bmw aka boostin4fun, etc. Cincy335i is one of his buddies who is trying to cover up for him.

Delta, if you couldnt keep up with this list on another forum why start another one here? Good luck with your new name, I doubt it will last long once the mods and admins find out.

Also, does anyone find it weird that a m3 owner complied a list of errors seen only by users with the n54 motor....odd.

Give it up Delta, your banned from every forum.
Italia335i is offline  
0
Reply With Quote
      05-07-2009, 05:16 PM   #10
Humtek
Vishnu Powered
 
Humtek's Avatar
 
Drives: 335xi, S1000RR
Join Date: Nov 2007
Location: Proceding

Posts: 2,205
iTrader: (7)

I think Delta got reinstated on these forums anyways. So whats the problem?

Can we keep this thread on topic so we can provide useful info.
__________________
2008 335xi Sedan | Titanium Silver | Black Dakota
PROcede v5 | Vishnu Exhaust | BMS DCI | AR Catless DPs | Helix FMIC | Stett Charge w/ Tial BOV | MORR VS8s | KWv3
Humtek is offline   United_States
0
Reply With Quote
      05-07-2009, 05:16 PM   #11
#1Stunna
Enlisted Member
 
#1Stunna's Avatar
 
Drives: '09 e92 m3, e92 335i
Join Date: Apr 2009
Location: Earth

Posts: 31
iTrader: (1)

Quote:
Originally Posted by cincy335i View Post
Thanks for all of your efforts on this, it is really helpful. This must have taken a lot of time and effort and I think that it is really helpful. Thanks again. Cheers!
Thanks guys! Keep them coming.
#1Stunna is offline  
0
Reply With Quote
      05-07-2009, 05:18 PM   #12
Italia335i
Banned
 
Drives: BMW
Join Date: Mar 2009
Location: USA

Posts: 88
iTrader: (1)

Quote:
Originally Posted by Humtek View Post
I think Delta got reinstated on these forums anyways. So whats the problem?

Can we keep this thread on topic so we can provide useful info.
Reinstated and banned again within 24 hours....shocker.
Italia335i is offline  
0
Reply With Quote
      05-07-2009, 05:22 PM   #13
cocoturkey
Lieutenant
 
Drives: 08' e92 335i
Join Date: Jan 2008
Location: Taipei

Posts: 441
iTrader: (0)

another contribution to the list


2A96:
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption


2DC5:
2DC5 Torque requirement via CAN controller area network, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed


51A6:
Error engine signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold
cocoturkey is offline   Taiwan
0
Reply With Quote
      05-07-2009, 05:23 PM   #14
dmurray14
The Stig
 
dmurray14's Avatar
 
Drives: Quickly
Join Date: Apr 2005
Location: US

Posts: 1,232
iTrader: (1)

This is great! I use a GT1 and the explanations are still wonderful to have!
__________________
dmurray14 is offline   United_States
0
Reply With Quote
      05-07-2009, 05:29 PM   #15
cincy335i
Lieutenant
 
cincy335i's Avatar
 
Drives: '08 Black Saph 335i coupe 6mt
Join Date: Mar 2009
Location: Cincinnati, Ohio

Posts: 418
iTrader: (0)

Quote:
Originally Posted by Italia335i View Post
Reinstated and banned again within 24 hours....shocker.
Who the hell are you, I don't see anything that says moderator next to your name? If you don't have anything to add to a useful thread, then move on, it really is that easy. Words of wisdom, don't start calling people out (me), when you have no idea what you are talking about...thanks.
cincy335i is offline  
0
Reply With Quote
      05-07-2009, 05:29 PM   #16
#1Stunna
Enlisted Member
 
#1Stunna's Avatar
 
Drives: '09 e92 m3, e92 335i
Join Date: Apr 2009
Location: Earth

Posts: 31
iTrader: (1)

Quote:
Originally Posted by cocoturkey View Post
another contribution to the list


2A96:
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption


2DC5:
2DC5 Torque requirement via CAN controller area network, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed


51A6:
Error engine signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold
Added. thank you for this set of codes also.
#1Stunna is offline  
0
Reply With Quote
      05-07-2009, 05:32 PM   #17
cocoturkey
Lieutenant
 
Drives: 08' e92 335i
Join Date: Jan 2008
Location: Taipei

Posts: 441
iTrader: (0)

a little more....




Radio gateway
Current Fault Codes
________________________________________

E18C
Device didn't accept or confirm monitoring message (Error_Monitoring)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
E18F
Central registry does not match with debit configuration (Error_Registry_New)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
cocoturkey is offline   Taiwan
0
Reply With Quote
      05-07-2009, 05:39 PM   #18
#1Stunna
Enlisted Member
 
#1Stunna's Avatar
 
Drives: '09 e92 m3, e92 335i
Join Date: Apr 2009
Location: Earth

Posts: 31
iTrader: (1)

Quote:
Originally Posted by cocoturkey View Post
a little more....




Radio gateway
Current Fault Codes
________________________________________

E18C
Device didn't accept or confirm monitoring message (Error_Monitoring)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
E18F
Central registry does not match with debit configuration (Error_Registry_New)
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
added. thank you for these also
#1Stunna is offline  
0
Reply With Quote
      05-07-2009, 05:42 PM   #19
Italia335i
Banned
 
Drives: BMW
Join Date: Mar 2009
Location: USA

Posts: 88
iTrader: (1)

Its weird, at first the OP only had an M3 but now he also has a 335i. Good stuff...
Italia335i is offline  
0
Reply With Quote
      05-07-2009, 05:44 PM   #20
Humtek
Vishnu Powered
 
Humtek's Avatar
 
Drives: 335xi, S1000RR
Join Date: Nov 2007
Location: Proceding

Posts: 2,205
iTrader: (7)

Quote:
Originally Posted by Italia335i View Post
Reinstated and banned again within 24 hours....shocker.
Are you the little taddle-tail kid who used to rat everyone out then get beat up at recess?
__________________
2008 335xi Sedan | Titanium Silver | Black Dakota
PROcede v5 | Vishnu Exhaust | BMS DCI | AR Catless DPs | Helix FMIC | Stett Charge w/ Tial BOV | MORR VS8s | KWv3
Humtek is offline   United_States
0
Reply With Quote
      05-07-2009, 05:51 PM   #21
cn555ic
BimmerPost Supporting Vendor

 
cn555ic's Avatar
 
Drives: Bimmerscoding.com
Join Date: Jun 2007
Location: New York

Posts: 18,278
iTrader: (5)

Send a message via Yahoo to cn555ic
what is 29F3? Can't seem to clear that code, even though the cars runs like a champ...Can a sensor be bad but not effect the performance of the car?
__________________
917-939-4980 CODING E and F Series New York Area

cn555ic is offline   United_States
0
Reply With Quote
      05-07-2009, 06:14 PM   #22
Italia335i
Banned
 
Drives: BMW
Join Date: Mar 2009
Location: USA

Posts: 88
iTrader: (1)

Quote:
Originally Posted by cn555ic View Post
what is 29F3? Can't seem to clear that code, even though the cars runs like a champ...Can a sensor be bad but not effect the performance of the car?
Have you tried removing your tune, clearing the codes with the BT cable, and see if it comes up again?
Italia335i is offline  
0
Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 04:39 PM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST