E90Post
 


PYSPEED
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Powertrain and Drivetrain Discussions > N54 Turbo Engine / Drivetrain / Exhaust Modifications - 335i > Best settings for the Proceed V3 on my car?



Reply
 
Thread Tools Search this Thread
      09-14-2009, 03:41 PM   #1
Malaka1
General
 
Malaka1's Avatar
 
Drives: E92 335i 6MT SGM
Join Date: Jun 2009
Location: Clearwater, FL

Posts: 730
iTrader: (6)

Best settings for the Proceed V3 on my car?

I just recently purchased the Proceed V3 w/ canbus.. I am wondering if someone could recommend the best map or user control settings for the most peak power?
My car:
2007 E92 335i 6mt
Vishnu DCI
UUC RSC335 axle-back
AR Design Catless DP's
Proceed V3 Rev.2

Can I run stage 3 even though I do not have an aftermarket fmic? And also Shiv when is the "bogfix" setting going to be available? I would like to get that map before I install the proceed so I don't have to go back into the ecu again..
Malaka1 is offline   United_States
0
Reply With Quote
      09-14-2009, 03:42 PM   #2
Zeph
Major
 
Drives: 2008 E92 335i 6MT SGM CR/BD
Join Date: Jul 2008
Location: Southeast USA

Posts: 1,393
iTrader: (0)

Send a message via AIM to Zeph Send a message via Yahoo to Zeph
Quote:
Originally Posted by Malaka1 View Post
I just recently purchased the Proceed V3 w/ canbus.. I am wondering if someone could recommend the best map or user control settings for the most peak power?
My car:
2007 E92 335i 6mt
Vishnu DCI
UUC RSC335 axle-back
AR Design Catless DP's
Proceed V3 Rev.2

Can I run stage 3 even though I do not have an aftermarket fmic? And also Shiv when is the "bogfix" setting going to be available? I would like to get that map before I install the proceed so I don't have to go back into the ecu again..
still using stock FMIC? I wouldn't go too aggressive unless you are in a hurry to heak-soak
Zeph is offline   United_States
0
Reply With Quote
      09-14-2009, 03:43 PM   #3
shiv@vishnu
 
shiv@vishnu's Avatar
 
Drives: PROcede v5
Join Date: Sep 2006
Location: SF Bay, CA

Posts: 17,609
iTrader: (0)

Quote:
Originally Posted by Malaka1 View Post
I just recently purchased the Proceed V3 w/ canbus.. I am wondering if someone could recommend the best map or user control settings for the most peak power?
My car:
2007 E92 335i 6mt
Vishnu DCI
UUC RSC335 axle-back
AR Design Catless DP's
Proceed V3 Rev.2

Can I run stage 3 even though I do not have an aftermarket fmic? And also Shiv when is the "bogfix" setting going to be available? I would like to get that map before I install the proceed so I don't have to go back into the ecu again..
My suggestion is to stick with the Stg 2 map with the standard default settings. There is no fixed setting for max power. It will depend on your conditions/fuel quality/etc,. To dial in your tune for max power, you will have to follow the custom tuning guide posted here. But the baseline map is a great place to start will get you 90% there without any work.

The bogfix update is still in testing so no official release date. Unofficially, i'd like to get it out to the public this week assuming beta testing goes perfectly. Just run the USB cable through your firewall and into your glovebox so you can update without having to get inside the ecu box again and again.

Shiv
shiv@vishnu is offline   United_States
0
Reply With Quote
      09-26-2009, 05:56 PM   #4
Malaka1
General
 
Malaka1's Avatar
 
Drives: E92 335i 6MT SGM
Join Date: Jun 2009
Location: Clearwater, FL

Posts: 730
iTrader: (6)

Got everything installed and I currently have user torque set to 80% and ign. correction to 75%.. feels powerful. I want more power though, lol, could I raise the user torque or lower the ign. correction at all to increase performance or should I stay here until I have a FMIC? *I am running Shell V Power 93 octane..
__________________
Cobb AccessPort, DCI, ....

R.I.P.
AW 335i 6MT FBO RB turbo's

Last edited by Malaka1; 09-26-2009 at 07:47 PM.
Malaka1 is offline   United_States
0
Reply With Quote
      09-26-2009, 06:32 PM   #5
cn555ic
BimmerPost Supporting Vendor

 
cn555ic's Avatar
 
Drives: The Coding Guy
Join Date: Jun 2007
Location: Call 917-939-4980

Posts: 18,227
iTrader: (5)

Send a message via Yahoo to cn555ic
Quote:
Originally Posted by Malaka1 View Post
Got everything installed and I currently have user torque set to 80% and ign. correction to 75%.. feels powerful. I want more power though, lol, could I raise the user torque or lower the ign. correction at all to increase performance or should I stay here until I have a FMIC?
Either FMIC or some Meth and you should see some significant gains....
__________________

Coding E and F New York 917-939-4980
cn555ic is offline   United_States
0
Reply With Quote
      09-26-2009, 06:55 PM   #6
Malaka1
General
 
Malaka1's Avatar
 
Drives: E92 335i 6MT SGM
Join Date: Jun 2009
Location: Clearwater, FL

Posts: 730
iTrader: (6)

Quote:
Originally Posted by cn555ic View Post
Either FMIC or some Meth and you should see some significant gains....
True, but could I net any more power just from adjusting the user torque setting or the ign. correction?
__________________
Cobb AccessPort, DCI, ....

R.I.P.
AW 335i 6MT FBO RB turbo's
Malaka1 is offline   United_States
0
Reply With Quote
      09-26-2009, 07:00 PM   #7
Prowess Symphony
Major General
 
Prowess Symphony's Avatar
 
Drives: ///Mistress
Join Date: Nov 2008
Location: WV

Posts: 5,598
iTrader: (11)

Garage List
Im not trying to thread jack. But did I understand correctly that you are able to set your own torque settings?
Prowess Symphony is online now   United_States
0
Reply With Quote
      09-26-2009, 07:23 PM   #8
Malaka1
General
 
Malaka1's Avatar
 
Drives: E92 335i 6MT SGM
Join Date: Jun 2009
Location: Clearwater, FL

Posts: 730
iTrader: (6)

Sort of..its 0-100% user torque which adjusts the boost, 80% is about 15.5-16psi I believe..100% is for stage3/methanol cars.. I dunno Shiv would be able to answer this better than myself.
__________________
Cobb AccessPort, DCI, ....

R.I.P.
AW 335i 6MT FBO RB turbo's
Malaka1 is offline   United_States
0
Reply With Quote
      09-27-2009, 08:28 AM   #9
Panoz
Lieutenant Colonel
 
Panoz's Avatar
 
Drives: E92 Space Grey 335i ,Aero Kit
Join Date: Nov 2006
Location: EU

Posts: 1,576
iTrader: (0)

Hey Malaka1,
Dont try funcy things with the maps. I would stick with the standard stage 2 settings ,as Shiv's proposal.
My car is a stage 2 car and I tried to bump up the settings almost close to the stage 3 levels. The car was pulling hard until the first two upshifts but as the IATs where increasing much quicker , Procede was tampering boost and the result was to run with 12,0-13,0 psi along he 5k-6,5K range.

Overall my car was slower...so keep it on the safe side.
__________________

Procede V4 , Catless DPs, Forge FMIC, Injen Intake, VK Oilcooler, Hartge Quads Exhaust, Modded CDV, Synapse BOV Kit, BMW Performance 335i SSK Kit, P3 vent boost gauge

Space Grey 335i -> See more pics HERE
Panoz is offline  
0
Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 12:27 AM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST