E90Post
 


N54Tuning.com
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > Mechanical Maintenance: Break-in / Oil & Fluids / Servicing / Warranty > Help!!! P1632 & P1417 Fault Codes



Reply
 
Thread Tools Search this Thread
      08-06-2013, 12:07 AM   #1
vwong
Lieutenant
vwong's Avatar
United_States
11
Rep
594
Posts

 
Drives: All Euro
Join Date: Jul 2007
Location: SoCal

iTrader: (3)

Send a message via AIM to vwong Send a message via Yahoo to vwong
Help!!! P1632 & P1417 Fault Codes

My car developed a problem. It's a 2009 E92 335i, N54, 6MT. Let me start with the events.

A little over a week ago, I was trying to pass a slower car. Downshifted to 2nd gear and got on the throttle a bit heavy. I heard a small pop, and immediately the CEL came on. I was still able to drive home with reduced power. When I got home, I used the PLX Device and the Rev app on the iPhone to check for codes (that's all I have, I don't have the BT scan tool). I got P0238 and P0113. I searched here and found that it could be a charge pipe that popped off or the boost pressure sensor disconnected. The pipes appear to be fine, but the connector that is supposed to plug into the boost pressure sensor was dangling. I try plugging it back in, but the locking mechanism is broken.

Anyway, I took it to the dealer and have them check it out in case there was more than just the sensor. Well, they confirmed it was the sensor. Since I'm out of warranty, I decided not to have the dealer to replace the sensor. I bought one from ECS Tuning (BMW p/n is 13627585493). The part number is different from the one on the broken sensor (p/n 13627551429), but according to ECS Tuning, the 493 superseded the broken one.

I installed it about an hour ago. After the installation, I cleared the old codes using the iPhone app. When I first started the engine, it ran very smoothly. I decided to take it out for a test drive. It ran fine for about half a block. I tried to get on the throttle a little harder, I immediately felt something wasn't right. The car threw the CEL again, and this time the throttle was non-responsive. The engine would still idle, but it fluctuates between 1000 to about 1500 rpm. Because of this fluctuation, I was able to limp home and checked codes. It now has the codes P1632 and P1417. Again, I searched here and found that P1632 means "Throttle Valve Adaptation; Adaptation Condition Not Met". Not sure what P1417 is since it's not listed. I'm wondering since the part number of the new boost pressure sensor is different from the broken one, does the ECU need to register it in order to function properly?

Anything else I should check? I'd appreciate any help anyone can offer. Thanks very much.

p.s. BTW, my car is all stock. So the codes aren't triggered by any aftermarket tunes.
__________________
2010 Audi S4 6MT
2009 BMW 335i Coupe 6MT
YouTube Channel

Last edited by vwong; 08-06-2013 at 12:23 AM. Reason: More background info
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 08:37 PM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST