How-To: Procede v4 PnP harness update (optional) - Page 5 - BMW 3-Series (E90 E92) Forum

s2k_335i · 12-09-2010, 09:04 PM

Shiv-
When i did this earlier today, the car start and ran fine. I went for a ride to Walmart and when I got back out to start the car, it went to a limp mode. The engine start to shake and the car shut down. I started the car again and the same problem but when i give it a little gas, its was fine. What do you think the issue is? The connection looks exactly like yours and I only removed any unused pin.
The Injectors, plugs, and wastegate was replaced in October. I'll run the computer tomorrow to check for the error.
I have AMS IC, DP, Intake, Procede v4.
Any help would greatly appreciated.

enrita · 12-09-2010, 09:36 PM

Did you clear the adaptations and reset ecu? Also tape those yellow cables.

s2k_335i · 12-09-2010, 10:17 PM

yes, i did.

shiv@vishnu · 12-09-2010, 10:25 PM

Hard to say without knowing the code. Once you know that, it will be easy to troubleshoot.

s2k_335i · 12-10-2010, 12:54 PM

The code is 12140, which translate to the following:
2F6C 12140 Exhaust fumeflap, input signal

The car start up fine today and ran fine without any error. I wonder how the car went into the limp mode related to this new mod.

Glowin · 12-10-2010, 12:59 PM

Quote:

Originally Posted by s2k_335i

The code is 12140, which translate to the following:
2F6C 12140 Exhaust fumeflap, input signal

The car start up fine today and ran fine without any error. I wonder how the car went into the limp mode related to this new mod.

That's just the code related to the exhaust flap actuator in the trunk that you've disabled. That's nothing.

s2k_335i · 12-10-2010, 01:16 PM

I understand the code but I might have cleared the other codes when this happened. Just hoping this issue will not happen again. It would be painful to get the IC, DP, intake, and procede remove again for dealer visit.

Intricacy · 01-04-2011, 07:00 PM

On some of the harnesses are these wires purple??

Intricacy · 01-10-2011, 01:11 PM

Quote:

Originally Posted by Intricacy

On some of the harnesses are these wires purple??

??

shiv@vishnu · 01-10-2011, 04:05 PM

Quote:

Originally Posted by Intricacy

On some of the harnesses are these wires purple??

Yep.

michael1284 · 01-18-2011, 02:52 PM

Quote:

Originally Posted by Intricacy

On some of the harnesses are these wires purple??

Quote:

Originally Posted by shiv@vishnu

Yep.

Ah..thought I was going crazy. Took my tune out last night for some warranty work and was going to do the harness update. Looks like it was already done which I thought was weird since I bought the Procede 4 months ago used from another member. Since I had the purple wires I kept scratching my head as to why it didn't look like the pic. Guess I was just surprised that someone 4 months ago already had this update done!

Anyone know what the blue connector is for in the second picture?

enrita · 01-18-2011, 03:35 PM

Quote:

Originally Posted by michael1284

Ah..thought I was going crazy. Took my tune out last night for some warranty work and was going to do the harness update. Looks like it was already done which I thought was weird since I bought the Procede 4 months ago used from another member. Since I had the purple wires I kept scratching my head as to why it didn't look like the pic. Guess I was just surprised that someone 4 months ago already had this update done!

Anyone know what the blue connector is for in the second picture?

Progressive meth

michael1284 · 01-18-2011, 05:23 PM

thanks!

Alan l. · 01-22-2011, 03:05 PM

Shiv - can you post a picture of which two red wires you used from the other sub connector? I am doing the update on the kitchen table so I dont have the factory harness in front of me to tell which one isn't being used.

Thanks!
Alan

cstmx_ryder · 01-22-2011, 03:07 PM

And, and for those with the "updated" harness, and not the brand new units from V4.....Which wires can I extract?

Mine doesn't have the yellow, blue, or green wires. Just the existing ones from V3 and was tweeked by Vishnu.

TIA

orionredwing · 01-22-2011, 03:58 PM

Just a clarification for reversing the process for emissions. After removing the equivalent of the 2 red wires shown in your example,

1) 2 female ends on the yellow wires would go into pins 19, and 20, correct?

2) How about the single male end? Is it pin 6 or 7? The other pin would be left open?

shiv@vishnu · 01-22-2011, 04:28 PM

Quote:

Originally Posted by orionredwing

Just a clarification for reversing the process for emissions. After removing the equivalent of the 2 red wires shown in your example,

1) 2 female ends on the yellow wires would go into pins 19, and 20, correct?

2) How about the single male end? Is it pin 6 or 7? The other pin would be left open?

1) Correct

2) Doesn't matter. Either one will be fine. You will have 1 empty terminal.

Schnitzel · 01-22-2011, 05:25 PM

Quote:

Originally Posted by s2k_335i

Shiv-
When i did this earlier today, the car start and ran fine. I went for a ride to Walmart and when I got back out to start the car, it went to a limp mode. The engine start to shake and the car shut down. I started the car again and the same problem but when i give it a little gas, its was fine. What do you think the issue is? The connection looks exactly like yours and I only removed any unused pin.
The Injectors, plugs, and wastegate was replaced in October. I'll run the computer tomorrow to check for the error.
I have AMS IC, DP, Intake, Procede v4.
Any help would greatly appreciated.

Had time to do the update today and had exactly the same problem. After restarting the car the problem did not appear anymore.

wren57 · 03-20-2011, 06:25 PM

Quote:

Originally Posted by Alan l.

Shiv - can you post a picture of which two red wires you used from the other sub connector? I am doing the update on the kitchen table so I dont have the factory harness in front of me to tell which one isn't being used.

Thanks!
Alan

+1

Jeff@TopGearSolutions · 03-20-2011, 06:39 PM

I've yet to do this. LOL

MKE_M3 · 03-20-2011, 07:24 PM

just did mine yesterday. Went smooth but I wish Vishnu made specific wires suggestions for teh patch. I was nervous just picking two wires, even if I saw with my eyes that the oem cable had not wires in those slots.

wren57 · 03-21-2011, 03:33 PM

Quote:

Originally Posted by jdemetry

just did mine yesterday. Went smooth but I wish Vishnu made specific wires suggestions for teh patch. I was nervous just picking two wires, even if I saw with my eyes that the oem cable had not wires in those slots.

Wanna take a picture for us or tell us which red pins you removed?

12-09-2010, 09:04 PM	#89
s2k_335i This is it!! Drives: FBO 335i without meth Join Date: Jul 2010 Location: Land of Freedom Posts: 651 iTrader: (1)	Shiv- When i did this earlier today, the car start and ran fine. I went for a ride to Walmart and when I got back out to start the car, it went to a limp mode. The engine start to shake and the car shut down. I started the car again and the same problem but when i give it a little gas, its was fine. What do you think the issue is? The connection looks exactly like yours and I only removed any unused pin. The Injectors, plugs, and wastegate was replaced in October. I'll run the computer tomorrow to check for the error. I have AMS IC, DP, Intake, Procede v4. Any help would greatly appreciated. Attached Images

12-09-2010, 09:36 PM	#90
enrita Major General Drives: 335i - Big turbos Join Date: Sep 2008 Location: Italian in Sweden Posts: 6,806 iTrader: (0)	Did you clear the adaptations and reset ecu? Also tape those yellow cables. __________________ 07 335i AT - TD St.2 Turbos - COBB (Custom Cobb mapping by http://www.protuningfreaks.com/) - JB4G5 ISO - Okada Coils - NGK 5992 Plugs - E85 Walbro - Injen Intake - Helix IC - Snow Stg. 3 - Stett CP - AR DPs - midpipes 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - Level 10 AT upgrade - Alpina AT Flash

01-18-2011, 05:23 PM	#101
michael1284 Colonel Drives: 2009 AW E90 335i Join Date: Apr 2010 Location: DFW Posts: 2,445 iTrader: (40)	thanks! __________________ RIP e92. New project is ALIVE! Updated Pics!

01-22-2011, 03:05 PM	#102
Alan l. Brigadier General Drives: M-Sport 535xi Join Date: Jun 2009 Location: New York Posts: 3,649 iTrader: (8)	Shiv - can you post a picture of which two red wires you used from the other sub connector? I am doing the update on the kitchen table so I dont have the factory harness in front of me to tell which one isn't being used. Thanks! Alan __________________ Current - 2013 N55 535xi Msport SAT Retired - 2009 N54 335i Msport 6MT Retired - 2000 M52TU 323i ASA Supercharged 5MT More Photos of my car here

01-22-2011, 03:07 PM	#103
cstmx_ryder Colonel Drives: A metal box with a roundel Join Date: Jul 2007 Location: Portland, OR Posts: 2,540 iTrader: (2)	And, and for those with the "updated" harness, and not the brand new units from V4.....Which wires can I extract? Mine doesn't have the yellow, blue, or green wires. Just the existing ones from V3 and was tweeked by Vishnu. TIA __________________ '08 AW E90 335i PROcede V5 \| BMS DCI \| RR DPs \| ETS FMIC \| FORGE DVs \| Stett CP \| Vanguard \| PSS10

12-09-2010, 10:17 PM	#91
s2k_335i This is it!! Drives: FBO 335i without meth Join Date: Jul 2010 Location: Land of Freedom Posts: 651 iTrader: (1)	yes, i did.

12-09-2010, 10:25 PM	#92
shiv@vishnu BimmerPost Supporting Vendor Drives: PROcede v5 Join Date: Sep 2006 Location: SF Bay, CA Posts: 16,687 iTrader: (0)	Hard to say without knowing the code. Once you know that, it will be easy to troubleshoot.

12-10-2010, 12:54 PM	#93
s2k_335i This is it!! Drives: FBO 335i without meth Join Date: Jul 2010 Location: Land of Freedom Posts: 651 iTrader: (1)	The code is 12140, which translate to the following: 2F6C 12140 Exhaust fumeflap, input signal The car start up fine today and ran fine without any error. I wonder how the car went into the limp mode related to this new mod.

12-10-2010, 01:16 PM	#95
s2k_335i This is it!! Drives: FBO 335i without meth Join Date: Jul 2010 Location: Land of Freedom Posts: 651 iTrader: (1)	I understand the code but I might have cleared the other codes when this happened. Just hoping this issue will not happen again. It would be painful to get the IC, DP, intake, and procede remove again for dealer visit.

01-04-2011, 07:00 PM	#96
Intricacy Procede Drives: X6 xDrive35i Join Date: Jun 2007 Location: Canada Posts: 60 iTrader: (0)	On some of the harnesses are these wires purple??

01-22-2011, 03:58 PM	#104
orionredwing Captain Drives: 335i Sedan, 135i Coupe Join Date: Dec 2006 Location: San Jose Posts: 701 iTrader: (0) Garage List 2007 335i [5.00]	Just a clarification for reversing the process for emissions. After removing the equivalent of the 2 red wires shown in your example, 1) 2 female ends on the yellow wires would go into pins 19, and 20, correct? 2) How about the single male end? Is it pin 6 or 7? The other pin would be left open? __________________ PROcede \| AMS FMIC \| AR Catless DPs \| AR Oil Cooler \| BMS DCI Wavetrac LSD \| KW V3 w/ Swift Springs \| M3 Front Suspension

03-20-2011, 06:39 PM	#108
Jeff@TopGearSolutions BimmerPost Supporting Vendor Drives: C6 Z06, GSXR-750, 09 335i Join Date: Dec 2008 Location: TopGearSolutions.com Posts: 12,421 iTrader: (25)	I've yet to do this. LOL __________________ Latest Specials!! Email Me! Jeff@TopGearSolutions.Com Evolution Racewerks Charge Pipes and FMIC Sale ETS FMIC INTERCOOLER SALE! Cobb AP for BMW N54 & N55, Lowest Price! Like Us On Facebook For Discounts!

03-20-2011, 07:24 PM	#109
MKE_M3 Lieutenant Colonel Drives: 2011 e90 M3 Join Date: Feb 2009 Location: Milwaukee, WI Posts: 1,502 iTrader: (0)	just did mine yesterday. Went smooth but I wish Vishnu made specific wires suggestions for teh patch. I was nervous just picking two wires, even if I saw with my eyes that the oem cable had not wires in those slots.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search