E90Post
 


European Auto Source
 
BMW 3-Series (E90 E92) Forum > E90/E92/E93 Marketplace (For Sale / Trade / Wanted) > SPONSORS Classifieds/Groupbuys/Specials Area > Turbo Engine / Drivetrain / Exhaust Parts > "RB" OEM Turbo TD03L-10T CHRA Centersections NEW (or USED) DIY Offering!!



Reply
 
Thread Tools Search this Thread
      11-21-2016, 01:02 PM   #1
Rob@RBTurbo
BimmerPost Supporting Vendor
Rob@RBTurbo's Avatar
107
Rep
1,390
Posts


Drives: 335I
Join Date: Jan 2008
Location: St. Louis, MO

iTrader: (5)

"RB" OEM Turbo TD03L-10T CHRA Centersections NEW (or USED) DIY Offering!!

RB Turbo now has NEW TD03L-10T CHRA rebuilds completed and available. We started by having some custom "larger than TD04" Thrust Upgrade hardware made to adapt into the TD03 OEM turbos ensuring that these will be better than what they were new. The end result is a mega cheap new core CHRA for you all looking for a true better than OEM replacement but with standard performance, availability, AND budget in mind. As these cars are getting much cheaper they are also being purchased by the more mechanically inclined (or younger ambitious) types, so we do realize that budget and DIY is where it is going out there.

Ultimately what you get are 100% OEM MHI CHRA's with all new bearings, seals, clips, and significantly beefed up thrust hardware so you can transplant them into your old housings and be off without a hitch. But keep in mind that even though they are "Plug and Play" that this is still a cumbersome DIY so you should have some confidence and the tools necessary to tear into your own turbo and make the install. Our intention is to not offer these and then get pounded with support questions along the way, as such we are keeping the cost very low. We are simply trying to provide the part that you need to get back on the road as your OEM turbos take a dump, so please make sure you understand what you are doing before purchase.

The cost is $385 per set OR $200 per CHRA*
*if ordered individually you must specify front or rear
NO CORE CHARGE!
NOTE: We can add a Billet 10T compressor/Custom Bullet Nut for $75 PER UNIT as well.

If you are in the USA the cost will be $400 shipped for the set or $210 shipped per unit. Our paypal is rob.rbturbo@gmail.com and you can also email the same address with any questions (ie. international shipping quotes, etc).

All units are all VSR balanced to under .2g to 200k RPM and each unit will come with its own balancing report.
__________________________________________________ _______________

We still also offer them as used take offs as well for $50 shipped anywhere in the USA for 1 unit or $90 shipped for 2 units (a set). Prefer not to ship used units International as the time it takes to ship anything international is a massive pain- will consider for bulkier orders though. Again this is a USED (unknown mileage) but complete Centersection with wheels and internals assembled. Most of them appear to be in usable condition as is but at minimum are in good serviceable condition for rebuild. We try to "cherry pick" each unit that is sold so keep in mind the more sales and time that goes by the appearance/condition will worsen marginally. We suspect many of these units could install as is and have a fairly performing turbo again, but overall there are no guarantees on these used take off turbos.
__________________________________________________ _______________

Keep in mind neither of these options (new or used) include ANY housings. They are solely the CHRA (aka the center section) complete with all rotating parts and wheels. This is an offering that allows you to service the center section of your own turbochargers for repairs.

Thanks,
Rob
Attached Images
   

Last edited by Rob@RBTurbo; 11-27-2016 at 10:08 PM.
Appreciate 0
      11-27-2016, 10:07 PM   #2
Rob@RBTurbo
BimmerPost Supporting Vendor
Rob@RBTurbo's Avatar
107
Rep
1,390
Posts


Drives: 335I
Join Date: Jan 2008
Location: St. Louis, MO

iTrader: (5)

Update: We can now offer a Billet 10T compressor wheel/bullet nut for $75 extra per unit. First post has been updated.
Appreciate 0
      02-15-2017, 07:49 PM   #3
Rob@RBTurbo
BimmerPost Supporting Vendor
Rob@RBTurbo's Avatar
107
Rep
1,390
Posts


Drives: 335I
Join Date: Jan 2008
Location: St. Louis, MO

iTrader: (5)

We've been consistently selling 2+ sets of CHRA's per week as of late, and yet another week with 3 sets of OEM rebuild CHRA's shipping out. Should be knocking on 20 sets of these out there very soon now.

Oh and a couple DIY Stage 1 kits (TD03L 9-blade with 14T Billets) too...

Rob
Attached Images
 
Appreciate 1
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 09:14 AM.




e90post
e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST