Lux Angel Eyes
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > DIY Guides > DIY -- Repair damaged thread with a HELICOIL

Tutorial Tools Search this Tutorial
DIY -- Repair damaged thread with a HELICOIL
Published by CALWATERBOY
Exclamation DIY -- Repair damaged thread with a HELICOIL

Vehicle: '09 E93 335i

Disaster! I cross threaded the mounting bolt for a M3 Guide Rod at my 3's Bearing Carrier!

Name:  Nervous.gif
Views: 2048
Size:  56.0 KB

After a lengthly bout of execration, steely calm engulfed my wah.

I knew what must be done: Travel, to Napa Auto Parts, there to select a M12 x 1.5 [12 mm fine thread, blue pkg] Helicoil installation set.

Name:  Helicoil Repair Kit [crop].jpg
Views: 1968
Size:  8.3 KB

Returning to my ride $80 lighter - Amazon much less but preferred not to wait - angst caused beads of sweat to form.....it was a warm day.....and I had never done this before....

First things first. Verifying that my mount bolt was spinning freely, this job did not require drilling out the threads. Some jobs do -- but my bearing carrier threads were completely stripped out.

I removed the bolt - had damaged threads near the tip which crunched & munched all bearing carrier threads going through. Only when the bolt was fully 'threaded' in did I find it could not be torqued! Nothing left to torque against.

Ran a cylindrical magnet through the hole - came out with a large ammt of shredded thread, leaving the hole more or less clean.

I inserted my tap into an Irwin adjustable tap socket, Home Depot, to cut threads into which the Helicoil will thread:
Name:  Irwin Adjustable Tap Socket.jpg
Views: 2486
Size:  15.2 KB
Name:  [01] 12 mm Tap with Irwin Holder.jpg
Views: 2130
Size:  186.1 KB

The tap supplied is of the self-guiding type. Just start it in the hole....

Name:  [02] Ready to start tap.jpg
Views: 2026
Size:  200.6 KB

....and ratchet until the tap has cut all the way through:

Name:  [03] Finished Bearing Carrier Tap.jpg
Views: 2066
Size:  133.3 KB

Then, the Helicoil, shown here with plastic install tool and threaded metal shank to thread the Helicoil into the hole:

Name:  [04] Helicoils and Installer.jpg
Views: 2099
Size:  201.6 KB

Drop a Helicoil tab first into the plastic installer....

Name:  [05] Drop a helicoil into installer.jpg
Views: 2044
Size:  100.0 KB

Insert the threaded shank....

Name:  [06] Insert Threaded Shank.jpg
Views: 1987
Size:  86.4 KB

Turn shank until a thread or two is exposed. Tab should be at the tip:

Name:  [07] Helicoil threads in tab first.jpg
Views: 2037
Size:  83.8 KB

Blow compressed air through the hole w/newly cut threads to remove debris.

Insert Helicoil tip into hole to be repaired and, holding the plastic installer with a wrench, turn the shank, thus threading the Helicoil into the threads you've cut for the purpose:

Name:  [08] Plastic installer held with box wrench while threaded shank is turned.jpg
Views: 2035
Size:  143.3 KB

When the Helicoil's fully installed, thread the shank out, leaving the coil in:

Name:  [09] Helicoil fully installed inlet view.jpg
Views: 2002
Size:  174.2 KB

The tab can be punched off, or left in for the bolt to snap it off as I did:

Name:  [10] Helicoil fully installed outlet view.jpg
Views: 2084
Size:  156.7 KB

When the mounting bolt's ratcheted in, it threads into the Helicoil which is designed to press against the threads cut with the tap. Result: Successful repair - a new bolt torqued normally to 100 N/M +90

I used Permatex 81343, Ace Hardware, on the threads.

Name:  Permatex 81343 Anti-Seize Lubricant 133 [50].jpg
Views: 1889
Size:  8.5 KB

Job done!

Name:  Mechanic.jpg
Views: 1934
Size:  7.5 KB

TIP: Love my GearWrench electronic torque wrench plus angle....
Tutorial Tools
By smellfish on 05-15-2012, 02:46 PM
Solid write-up! I stripped a water pump bolt on my old SR20 build. After I changed my underwear I used one of these kits, problem solved.
Reply With Quote
By Mauryk on 05-15-2012, 02:49 PM
Member reviews
Difficulty [ 1 = Difficult ]
Cost [ 1 = Expensive ]
DIY Clarity [ 1 = Not clear ]
Average 20%
Great write up!
Reply With Quote
By warpig666 on 05-17-2012, 05:27 PM
Great write up. Hopefully I will never have to use it. I think having to re-tap/thread a bolt hole (especially a hard to reach one) has to be one of the most disappointing, aggravating and frustrating things ever!
Reply With Quote
By jeguth1s on 04-17-2013, 07:56 AM
Thanks for this! I did the same stupid thing this weekend. I had to drill out my hole though. The hardest part was sourcing a drill that would fit in there! I did the other guide rod which is harder to access. Luckily 5 trip to home Depot later, I found the perfect drill. Also, 31/64" is the correct drill bit to use. Don't expect to find that at Home Depot or Lowe's either.
Reply With Quote


Tutorial Tools Search this Tutorial
Search this Tutorial:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -4. The time now is 09:05 AM.

Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2016, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST