E90Post
 


Extreme Power House
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > BMW Coding > About to give up! Coding windows up on 06



Reply
 
Thread Tools Search this Thread
      12-01-2012, 02:05 PM   #1
thecadman99
First Lieutenant
thecadman99's Avatar
9
Rep
373
Posts

 
Drives: e90 330i 6mt spt bk/bk
Join Date: Jun 2012
Location: Virginia

iTrader: (0)

About to give up! Coding windows up on 06

As per the coding instructions I have coded the CAS module- KOMFORTSCHLIESSUNG_FB from "nicht_aktiv" to "aktiv"

When I completely disconnect everything, and re-start ncsexpert, I re-read the module and it still correctly reads "aktiv" so I know the coding "took"

but- it doesn't work. I can roll the windows down as always with fob, but not back up.

The instructions I have state that the module to code is the CAS module but it also says in parenthesis (read from GM3) module. I did not use GM3.

The instructions I have always state to chose the CAS module (after choosing chassis) and I also select CAS a second time after clicking "process ecu"
Am I coding the wrong module?

Can someone point me in the right direction?
__________________
06 330i 6mt Spt- Eibach Springs, BMW Perf Susp, Supersprint Exhaust, BSW Audio
94 325i 5mt 4d- M3 springs/susp, Z3 wheels, Chipped, Intake, Exhaust= FUN!
Appreciate 0
      12-01-2012, 04:23 PM   #2
NiVeDh
Major General
NiVeDh's Avatar
United_States
158
Rep
8,014
Posts

 
Drives: '08 E90 335i, '99 E36 M3
Join Date: Apr 2009
Location: Houston, TX & Atlanta, GA

iTrader: (132)

Garage List
Are you using an NCS Expert profile that allows coding using .MAN files?
Appreciate 0
      12-01-2012, 07:08 PM   #3
thecadman99
First Lieutenant
thecadman99's Avatar
9
Rep
373
Posts

 
Drives: e90 330i 6mt spt bk/bk
Join Date: Jun 2012
Location: Virginia

iTrader: (0)

Yes, I am reading the ecu, renaming the file to a .man, editing with notepad, then writing back to ecu
__________________
06 330i 6mt Spt- Eibach Springs, BMW Perf Susp, Supersprint Exhaust, BSW Audio
94 325i 5mt 4d- M3 springs/susp, Z3 wheels, Chipped, Intake, Exhaust= FUN!
Appreciate 0
      12-05-2012, 03:03 PM   #4
cyrano
Banned
Poland
2
Rep
145
Posts

 
Drives: E61 530XD chipped
Join Date: Apr 2011
Location: Poland

iTrader: (0)

You need to code it n cas and also frm/nfrm
Appreciate 0
      12-05-2012, 03:31 PM   #5
Elliott@DetailAddict
Brigadier General
United_States
81
Rep
4,448
Posts

 
Drives: E90
Join Date: May 2011
Location: Santa Clara, CA

iTrader: (0)

It seems you are using the Expert Profile when you first open NCS, or you set up your FSW profile wrong.

That is why it is not sticking.

Cyrano, not sure what you mean? He's not editing a VO, and the only code in NFRM/FRM using the key fob is mirrors folding which does not have to be aktiv for the windows to roll up from the fob.
Appreciate 0
      12-09-2012, 02:21 PM   #6
bmwcod
Registered
0
Rep
3
Posts

 
Drives: M6
Join Date: Dec 2012
Location: Toronto

iTrader: (0)

Try updating your daten files to the newest version
Appreciate 0
      12-12-2012, 02:33 AM   #7
mikefromMA
First Lieutenant
United_States
4
Rep
306
Posts

 
Drives: 2013 e92 M3
Join Date: Aug 2011
Location: MA

iTrader: (6)

Garage List
2013 M3  [4.50]
2013 BMW x3  [0.00]
If you have't already, try changing job name when finished prior to executing.
Appreciate 0
      12-12-2012, 03:21 AM   #8
ctuna
Brigadier General
45
Rep
4,327
Posts

 
Drives: 325xi 06 wagon MT
Join Date: Jan 2010
Location: Santa Cruz, Ca

iTrader: (0)

FYI found the procedure I used

After you run a Consistency Check, you need to create a profile that you use from then on to write to the car called a .man file

In NCSExpert:
File > Load profile > Expertmode > OK
File > edit profile (Password is 'repxet')
Select 'car-keymemory' (check all 3 boxes) > OK
Select 'Consistency Check' (should say 'OK') > OK
Select 'FSW/PSW' ('CVT' selected + both bottom check boxes) > OK
Select 'Consistency Check' (should say 'OK') > OK

Then create the .man file:
File > save profile as > (Enter 'Filename' CSEXPER\PFL\xxxx.PFL) > OK
xxxx = 4 digit name of your choosing, not same as what is currently in file name
File > edit profile (Password is 'repxet') > profile info > set profile name = 'FSW PSW MAN'
You need to load this profile from now on EVERY time you enter NCSExpert to code


After that is done, to code:

Start NCSExpert
File > > load profile > 'FSW PSW MAN' (will load what you just created above)
F1 > F3 > E89 > select 'CAS'
F6 (or back)
F4 (Process ECU)> select module you want to code, for Windows Up it will be 'CAS' > OK > 'Read ECU'

This will create a FSW_PSW.TRC file for ONLY the module you selected

Close the screen that comes up with all the chinese writing
Go to Work Folder
Open FSW_PSW.TRC file with Notepad
File > save as all > 'FSW_PSW.MAN'

The FSW PSW MAN profile that you just created earlier will use this FSW_PSW.MAN file & this is where you will make your changes
Open file FSW_PSW.MAN (you should see all the code lines for the module)
Find 'KOMFORTSCHLIESSUNG_FB' (for windows up thru key fob) -or- 'KOMFORTSCHLIESSUNG_PA' (for windows up thru comfort access) > change to 'aktiv'
File > save
Go back to NCS and select F5
Select 'coapiReadSgGETFSWPSW' > OK (reads all the values including the one you just changed)
At next screen > OK (should then say 'basic function perfect ended') > OK
Select F2 (job)
Select 'SG_CODIEREN > OK
Select F3 (to execute job)
screen will gray out then you should see 'coding ended' message. Test windows to see if they work
Appreciate 0
      12-15-2012, 02:27 AM   #9
xxxjecxxx
Captain
xxxjecxxx's Avatar
66
Rep
809
Posts

 
Drives: Jet Black 06 325i LCI
Join Date: Aug 2009
Location: Orlando, FL

iTrader: (1)

The profile comes with the NCSExpert rar file, you don't need to creat it. Also you have a 06 which will work with the V39 Daten files (also already included).
Your problem is in the procedure, follow advice above or look at the youtube video.
Appreciate 0
      12-20-2012, 06:27 PM   #10
thecadman99
First Lieutenant
thecadman99's Avatar
9
Rep
373
Posts

 
Drives: e90 330i 6mt spt bk/bk
Join Date: Jun 2012
Location: Virginia

iTrader: (0)

Thanks much all. A forum member was kind enough to help me through pm. I won't say who so they don't get bombarded with requests, but it was my procedure.
__________________
06 330i 6mt Spt- Eibach Springs, BMW Perf Susp, Supersprint Exhaust, BSW Audio
94 325i 5mt 4d- M3 springs/susp, Z3 wheels, Chipped, Intake, Exhaust= FUN!
Appreciate 0
      12-21-2012, 03:32 PM   #11
crashoverride
Second Lieutenant
4
Rep
202
Posts

 
Drives: na
Join Date: Jul 2006
Location: na

iTrader: (0)

Quote:
Originally Posted by xxxjecxxx
The profile comes with the NCSExpert rar file, you don't need to creat it. Also you have a 06 which will work with the V39 Daten files (also already included).
Your problem is in the procedure, follow advice above or look at the youtube video.
Uhm I'm new to all this but why would a 2006 e90 work with/use e39 daten files?


(Well this is actually somewhat correct as far as I can see as the 2006 two door e90 wasn't built till 2007)
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 01:31 AM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST