E90Post
 


TireRack
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Powertrain and Drivetrain Discussions > N54 Turbo Engine / Drivetrain / Exhaust Modifications - 335i > GTech-Pro Install and RPM Calibration



Reply
 
Thread Tools Search this Thread
      08-16-2007, 12:04 AM   #1
roy@gambitmotorsport
Something Else
 
roy@gambitmotorsport's Avatar
 
Drives: '07 335i coupe 6MT
Join Date: Jul 2007
Location: Los Angeles, CA

Posts: 216
iTrader: (0)

GTech-Pro Install and RPM Calibration

I just hooked up my GTech-Pro and am loving it!

I did a hardwire install using the included screw-in bracket, but on the dash trim with industrial-strength double-sided tape, since I didn't want to block my front view at all (pics below). Then I ran the chord down behind the glovebox and rigged something up to a fuse tap you can buy from Autozone which I read about on a radar detector hardwire install DIY here. I lost the functionality of the driver's cup holder, but hey, that's just for us Americans, right? It looks incredibly sweet with matching aluminum trim and red/orange backlights.

I had the typical RPM calibration issues folks talk about and went with manual map #18 as suggested on another thread here. This worked good for me, but only over a couple of thousand RPMs in 3rd gear. I found that once you got to this point, they stayed proper even if you backed off down into second gear sometimes. I figured something variable was up, rather than just super line conditioning by BMW, performed a couple of tests, and found it to be the "smart" A/C. You know, when you floor it, the A/C reduces (at least in low gear), I suppose to provide full strength to the engine. Well, this has the effect of leveling out the electrical system. When I turn off the A/C, even my revs out of gear are picked up well. Not that I'm going to be doing that soon with the 100 degree weather currently in SoCal, but it's good to know what the issue is and to put it to rest, so I thought I'd pass it on.

Can't wait to take a few runs up the local twisties and compare. I'm still at around 400 miles, so I'm not going for the best 0-60 runs right now, though I did once last night (unrecorded) when a guy in a G35 tried to race me; "tried" being the key word.
Attached Images
  
roy@gambitmotorsport is offline   United_States
0
Reply With Quote
      08-16-2007, 01:24 PM   #2
Vince@ V K Motorwerks
Lieutenant Colonel
 
Vince@ V K Motorwerks's Avatar
 
Drives: 01 Black 911 Turbo, 09 X5
Join Date: May 2007
Location: Bloomingdale, IL

Posts: 1,739
iTrader: (0)

I just bought some jumpers and hooked up my Gtech ss to the battery but I still cant get it to configure completely right. But I only messed with it about 2 times so far. Fun little gadget isnt it. The funny thing is I placed mine in the same location as yours.
Vince@ V K Motorwerks is offline  
0
Reply With Quote
      08-17-2007, 04:14 AM   #3
hotrod182
.
 
hotrod182's Avatar
 
Drives: 07 335i, 06 M3
Join Date: Dec 2006
Location: California

Posts: 3,461
iTrader: (0)

You can contact Tesla, but I am pretty sure that you can't have the display angled towards you when you make the run. Do you turn it straight forward when you make the runs?
hotrod182 is offline  
0
Reply With Quote
      08-17-2007, 04:18 AM   #4
nico335
Guest
 
Drives:

Posts: n/a
what do you have to connect the gtech to in order for it to function properly? not talking about hardwiring though....
 
0
Reply With Quote
      08-17-2007, 04:27 AM   #5
bnj
Banned
 
Drives: e92 335i
Join Date: Nov 2006
Location: Helsinki

Posts: 1,137
iTrader: (0)

Quote:
Originally Posted by that guy nico View Post
what do you have to connect the gtech to in order for it to function properly? not talking about hardwiring though....
You mean to be able to measure rpm? I would like to know that well..
bnj is offline  
0
Reply With Quote
      08-17-2007, 12:52 PM   #6
roy@gambitmotorsport
Something Else
 
roy@gambitmotorsport's Avatar
 
Drives: '07 335i coupe 6MT
Join Date: Jul 2007
Location: Los Angeles, CA

Posts: 216
iTrader: (0)

Quote:
Originally Posted by hotrod182 View Post
You can contact Tesla, but I am pretty sure that you can't have the display angled towards you when you make the run. Do you turn it straight forward when you make the runs?
Not to disagree, but I'm almost positive it can be angled in any direction. The thought did cross my mind, too. But, the manual (which I read in its entirety) doesn't state this and there is an "orientation" phase you take it through, which is simply a first-time straight-line drag run, so it can gather which direction is forward.

Accelerometers with the proper driver software could definitely handle the task. At a physical level, I believe they pick up changes in direction the same way throughout 3D space. Going off on a total tangent, if anyone's interested, many laptops have an accelerometer built-in nowadays. If it senses a quick change in direction, it "parks" the hard drive, to protect from head crashes in the event it has been dropped and is about to be jarred hard.
roy@gambitmotorsport is offline   United_States
0
Reply With Quote
      08-17-2007, 01:04 PM   #7
roy@gambitmotorsport
Something Else
 
roy@gambitmotorsport's Avatar
 
Drives: '07 335i coupe 6MT
Join Date: Jul 2007
Location: Los Angeles, CA

Posts: 216
iTrader: (0)

Quote:
Originally Posted by that guy nico View Post
what do you have to connect the gtech to in order for it to function properly? not talking about hardwiring though....
It just needs power. It picks up G forces (acceleration, braking, turning) directly with its accelerometer. It deduces speed based on changes in G forces. It calculates HP/Tq based on these and the vehicle weight you enter. It does its best to "sense" the RPMs by power fluctuations in the vehicle's electrical system. My findings are that the variable-rate air conditioning makes the RPM pick-up extremely hard for it at low revs. But, thanks to _ulises 335i_ here, manually selecting RPM map 18 matches things up well.
roy@gambitmotorsport is offline   United_States
0
Reply With Quote
      08-17-2007, 01:23 PM   #8
nj335i
Modaholic
 
nj335i's Avatar
 
Drives: with 3 pedals
Join Date: Jan 2007
Location: East Coast

Posts: 1,699
iTrader: (7)

Is that a suction cup mount? I actually have a GPS that I'd like to mount in that location, but the suction cup doesn't work on the aluminum trim...
__________________
Euro Delivery - April 2007

nj335i is offline   United_States
0
Reply With Quote
      08-17-2007, 02:43 PM   #9
Hunter399
Major General
 
Hunter399's Avatar
 
Drives: F30 335i
Join Date: Apr 2005
Location: Houston, TX

Posts: 7,757
iTrader: (30)

Quote:
Originally Posted by roy@gambitmotorsport View Post
Not to disagree, but I'm almost positive it can be angled in any direction. The thought did cross my mind, too. But, the manual (which I read in its entirety) doesn't state this and there is an "orientation" phase you take it through, which is simply a first-time straight-line drag run, so it can gather which direction is forward.

Accelerometers with the proper driver software could definitely handle the task. At a physical level, I believe they pick up changes in direction the same way throughout 3D space. Going off on a total tangent, if anyone's interested, many laptops have an accelerometer built-in nowadays. If it senses a quick change in direction, it "parks" the hard drive, to protect from head crashes in the event it has been dropped and is about to be jarred hard.
I think it needs to be straight too because I'm not sure if the g-tech has that capacity. But what you can do is try it angled and try it straight and see if the numbers are significantly different.
Hunter399 is offline  
0
Reply With Quote
      08-17-2007, 04:09 PM   #10
roy@gambitmotorsport
Something Else
 
roy@gambitmotorsport's Avatar
 
Drives: '07 335i coupe 6MT
Join Date: Jul 2007
Location: Los Angeles, CA

Posts: 216
iTrader: (0)

Quote:
Originally Posted by nj335i View Post
Is that a suction cup mount? I actually have a GPS that I'd like to mount in that location, but the suction cup doesn't work on the aluminum trim...
The GTech comes with a suction cup mount and a permanent screw-in mount. After deciding that I'll probably never really want to take it off, I used the screw-in mount, but with industrial strength two-sided tape instead of screws. If your suction cup is shallow enough, I imagine you could use the tape, too.
roy@gambitmotorsport is offline   United_States
0
Reply With Quote
      08-17-2007, 04:33 PM   #11
roy@gambitmotorsport
Something Else
 
roy@gambitmotorsport's Avatar
 
Drives: '07 335i coupe 6MT
Join Date: Jul 2007
Location: Los Angeles, CA

Posts: 216
iTrader: (0)

Quote:
Originally Posted by hunter399 View Post
I think it needs to be straight too because I'm not sure if the g-tech has that capacity. But what you can do is try it angled and try it straight and see if the numbers are significantly different.
I've sent the manufacturer an email about it and will let you guys know what they come back with. They sometimes take a while... However, I think if the angle was important it would be mentioned repeatedly throughout the docs (which are quite extensive) and I found no word of it, although there are tons of cautions for all other sorts of things.

After a run up the Angeles Crest today, I can say that my left and right cornering Gs are near identical, although that's not proof and forward acceleration could be handled differently. If I'm right, I guess there will be one bummed Ford F150 Lightning owner out there.

http://www.f150online.com/forums/showthread.php?t=28437
roy@gambitmotorsport is offline   United_States
0
Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 07:10 AM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST