P/N vacuum line "T" fitting for diverter valve - BMW 3-Series (E90 E92) Forum

335ibob · 10-22-2007, 10:42 AM

Does anyone know the part number for the plastic "T" fitting that connects the vacuum line to the diverter valves? Or anywhere I can get a substitute for it?

e90AW335i · 10-22-2007, 10:44 AM

I haven't seen it, but if it looks like a small plastic hose barb you can get those at any local hardware store....

MBMWTECH · 10-22-2007, 10:52 AM

Quote:

Originally Posted by 335ibob

Does anyone know the part number for the plastic "T" fitting that connects the vacuum line to the diverter valves? Or anywhere I can get a substitute for it?

I think what your looking for is #15 part number 13-71-7-577-742

e90AW335i · 10-22-2007, 10:55 AM

If it is part number 15 then a local hardware store would definitely have that....I know getting it from BMW is better, but if you don't want to wait then that is an option....

BoostedBMW · 10-22-2007, 11:03 AM

When I needed a quick vacuum T I would just go to TrueValue or Ace hardware, they usually have them in a few different sizes, but I have only seen white ones there, not black.

335ibob · 10-22-2007, 11:04 AM

thanks for the quick responses MBMWTECH, kyleh4852 & boostedBMW I appreciate it...I'll try bmw and if they don't have it I'll check out Home Depot...any idea what area this item would be ie plumbing?

BoostedBMW · 10-22-2007, 11:10 AM

Quote:

Originally Posted by 335ibob

thanks for the quick responses MBMWTECH, kyleh4852 & boostedBMW I appreciate it...I'll try bmw and if they don't have it I'll check out Home Depot...any idea what area this item would be ie plumbing?

Honestly I don't even know because Ace hardware/TrueValue usually has them in the huge stack of drawers that they have behind the register. I never go to home depot for stuff like that because if they have it I can never find it.

e90AW335i · 10-22-2007, 11:11 AM

They would be in the pluming section, if you can find someone ask where to find "hose barbs" and then just look around. If might help if you can cut a small piece of the hose off so that you can check the size. Good luck!

Edit: They will probably be in a "T" shape and not a "Y' . Although it will still work.....

335ibob · 10-22-2007, 11:41 AM

Does anyone know the size of the stock "T" fitting for the vacuum hose? 1/8 or 3/16?

BoostedBMW · 10-22-2007, 11:45 AM

Quote:

Originally Posted by 335ibob

Does anyone know the size of the stock "T" fitting for the vacuum hose? 1/8 or 3/16?

I'm not positive, but this is what I used to install my boost gauge...

http://www.namotorsports.net/detail....d/DD42-150-851

I think that the T fitting is 1/8" and the vac line was 3/16".

Shinchan · 10-22-2007, 01:28 PM

This is the part number.

13-71-7-577-742

I got few of them for Crown auto. THey are not cheap.. Nothing u can get from auto store that looks like Y shape and black. I got mine for a price to remain stock....

Shinchan · 10-22-2007, 01:29 PM

while u are at it buying from Crown.. might as well as buy few OEM Black T connector.. those are about 0.61.

and the Y COnnector is 4.23/each.

Raz335 · 10-22-2007, 01:46 PM

A little OT, but does anyone have the P/N for the small (2") rubber vacum hose that connects from the T fitting to the Solenoid? Or know what size it is to get it at a local hardware store?

sambonator · 10-22-2007, 01:59 PM

Are the T's you get at hardware stores able to survive in the hot engine compartment?

e90AW335i · 10-22-2007, 02:08 PM

Quote:

Originally Posted by sambonator

Are the T's you get at hardware stores able to survive in the hot engine compartment?

If you are worried about plastic you can always go with a brass one....they should have both.....

MBMWTECH · 10-22-2007, 02:11 PM

Quote:

Originally Posted by Raz335

A little OT, but does anyone have the P/N for the small (2") rubber vacum hose that connects from the T fitting to the Solenoid? Or know what size it is to get it at a local hardware store?

HEY RAZ335 REFERANCE THE PICTURE I POSTED ABOVE
HERES ALL THE PART NUMBERS IN THAT PICTURE.

ITS NUMBER 16
FOR FUTURE REFERANCE CHECK OUT REALOEM.COM IT GIVES PICTURE AND PART NUMBERS (AND SOME PRICES) FOR ANY BMW.

01 CHARGE AIR INDUCTION TRACT 1 11657556551
02 O-RING 2 13717568030
03 PREFORMED SEAL 1 11617791470
04 CLAMP 2 11657558922
05 CHARGE AIR INDUCTION TRACT 1 11657556554
06 PRESSURE SENSOR 1 13627551429
07 PLUG HOUSING ON REQUEST 1 61133333333
08 FILLISTER HEAD SCREW 2 51417067920
09 GROMMET 1 13717568028
10 BUSH WITH SCREW M6X22 1 13717568027
11 O-RING 1 13717568031
12 BRACKET, CHARGE-AIR DUCTING 1 11657556962
13 TUBE, TURBOCHARGER BYPASS 1 11657556556
14 TUBE, TURBOCHARGER BYPASS 1 11657556555
15 CONNECTION PIPE Y 1 13717577742
16 VACUUM HOSE BLACK 3,5X2,0 ? 11747797129
17 HOSE CLAMP D= 65-72MM 1 11617786528
18 CHARGE AIR INDUCTION TRACT 1 11657556553
19 PREFORMED SEAL 1 11617791469

Vince@ V K Motorwerks · 10-22-2007, 02:12 PM

Quote:

Originally Posted by MBMWTECH

HEY RAZ335 REFERANCE THE PICTURE I POSTED ABOVE
HERES ALL THE PART NUMBERS IN THAT PICTURE.

ITS NUMBER 16
FOR FUTURE REFERANCE CHECK OUT REALOEM.COM IT GIVES PICTURE AND PART NUMBERS (AND SOME PRICES) FOR ANY BMW.

01 CHARGE AIR INDUCTION TRACT 1 11657556551
02 O-RING 2 13717568030
03 PREFORMED SEAL 1 11617791470
04 CLAMP 2 11657558922
05 CHARGE AIR INDUCTION TRACT 1 11657556554
06 PRESSURE SENSOR 1 13627551429
07 PLUG HOUSING ON REQUEST 1 61133333333
08 FILLISTER HEAD SCREW 2 51417067920
09 GROMMET 1 13717568028
10 BUSH WITH SCREW M6X22 1 13717568027
11 O-RING 1 13717568031
12 BRACKET, CHARGE-AIR DUCTING 1 11657556962
13 TUBE, TURBOCHARGER BYPASS 1 11657556556
14 TUBE, TURBOCHARGER BYPASS 1 11657556555
15 CONNECTION PIPE Y 1 13717577742
16 VACUUM HOSE BLACK 3,5X2,0 ? 11747797129
17 HOSE CLAMP D= 65-72MM 1 11617786528
18 CHARGE AIR INDUCTION TRACT 1 11657556553
19 PREFORMED SEAL 1 11617791469

Good to have someone on the "inside"

BoostedBMW · 10-22-2007, 02:14 PM

Quote:

Originally Posted by sambonator

Are the T's you get at hardware stores able to survive in the hot engine compartment?

I used them on my s2k without a problem and that engine bay use to get retardedly hot. I'm talking hot to the point that it melted one of my batteries and I had to relocate it!

Also, if it gets to the point where the plastic T will melt then your rubber vac lines probably aren't going to last very long anyway.

Raz335 · 10-23-2007, 04:00 PM

Quote:

Originally Posted by MBMWTECH

HEY RAZ335 REFERANCE THE PICTURE I POSTED ABOVE
HERES ALL THE PART NUMBERS IN THAT PICTURE.

ITS NUMBER 16
FOR FUTURE REFERANCE CHECK OUT REALOEM.COM IT GIVES PICTURE AND PART NUMBERS (AND SOME PRICES) FOR ANY BMW.

01 CHARGE AIR INDUCTION TRACT 1 11657556551
02 O-RING 2 13717568030
03 PREFORMED SEAL 1 11617791470
04 CLAMP 2 11657558922
05 CHARGE AIR INDUCTION TRACT 1 11657556554
06 PRESSURE SENSOR 1 13627551429
07 PLUG HOUSING ON REQUEST 1 61133333333
08 FILLISTER HEAD SCREW 2 51417067920
09 GROMMET 1 13717568028
10 BUSH WITH SCREW M6X22 1 13717568027
11 O-RING 1 13717568031
12 BRACKET, CHARGE-AIR DUCTING 1 11657556962
13 TUBE, TURBOCHARGER BYPASS 1 11657556556
14 TUBE, TURBOCHARGER BYPASS 1 11657556555
15 CONNECTION PIPE Y 1 13717577742
16 VACUUM HOSE BLACK 3,5X2,0 ? 11747797129
17 HOSE CLAMP D= 65-72MM 1 11617786528
18 CHARGE AIR INDUCTION TRACT 1 11657556553
19 PREFORMED SEAL 1 11617791469

Excellent! Thanks for the part list man. This will come in handy.

10-22-2007, 10:42 AM	#1
335ibob Enlisted Member Drives: 335i Join Date: Oct 2007 Location: SoCal Posts: 32 iTrader: (0)	P/N vacuum line "T" fitting for diverter valve Does anyone know the part number for the plastic "T" fitting that connects the vacuum line to the diverter valves? Or anywhere I can get a substitute for it?
	Tweet

10-22-2007, 11:03 AM	#5
BoostedBMW Moderator Drives: TiAg E92 335 Join Date: Oct 2006 Location: Raleigh, NC Posts: 6,784 iTrader: (14) Garage List 2003 S2000 [0.00]	When I needed a quick vacuum T I would just go to TrueValue or Ace hardware, they usually have them in a few different sizes, but I have only seen white ones there, not black. __________________ -Michael. Berlina Black S2000 CR is now in the garage l 19" Rial Daytona Race l KW V2 l Eisenhaus Race Exhaust l

10-22-2007, 01:28 PM	#11
Shinchan LED Rules Drives: Sold: 335xi Coupe Join Date: Oct 2006 Location: Boston Posts: 790 iTrader: (0)	This is the part number. 13-71-7-577-742 I got few of them for Crown auto. THey are not cheap.. Nothing u can get from auto store that looks like Y shape and black. I got mine for a price to remain stock.... __________________ LED Pimp... 13 Audi S4...

10-22-2007, 01:29 PM	#12
Shinchan LED Rules Drives: Sold: 335xi Coupe Join Date: Oct 2006 Location: Boston Posts: 790 iTrader: (0)	while u are at it buying from Crown.. might as well as buy few OEM Black T connector.. those are about 0.61. and the Y COnnector is 4.23/each. __________________ LED Pimp... 13 Audi S4...

10-22-2007, 01:46 PM	#13
Raz335 Major Drives: BMW M3 Convertible Join Date: Sep 2007 Location: LI,NY Posts: 1,043 iTrader: (2)	A little OT, but does anyone have the P/N for the small (2") rubber vacum hose that connects from the T fitting to the Solenoid? Or know what size it is to get it at a local hardware store? __________________ Jerez Black/Fox E93 M3 - Prem 2/Cold/Conv/DCT/EDC/19's/Ext Lthr/Crbn Trim/Enhanced Sound/Sat Gone - E92 335i - Sport \|Premium \|Cold \|Nav \|Step W/Paddles \|Comfort Access \|IPOD \|PDC

10-22-2007, 10:44 AM	#2
e90AW335i Major General Drives: e90 335i Join Date: Sep 2007 Location: ...... Posts: 6,608 iTrader: (4)	I haven't seen it, but if it looks like a small plastic hose barb you can get those at any local hardware store....

10-22-2007, 10:55 AM	#4
e90AW335i Major General Drives: e90 335i Join Date: Sep 2007 Location: ...... Posts: 6,608 iTrader: (4)	If it is part number 15 then a local hardware store would definitely have that....I know getting it from BMW is better, but if you don't want to wait then that is an option....

10-22-2007, 11:04 AM	#6
335ibob Enlisted Member Drives: 335i Join Date: Oct 2007 Location: SoCal Posts: 32 iTrader: (0)	thanks for the quick responses MBMWTECH, kyleh4852 & boostedBMW I appreciate it...I'll try bmw and if they don't have it I'll check out Home Depot...any idea what area this item would be ie plumbing?

10-22-2007, 11:11 AM	#8
e90AW335i Major General Drives: e90 335i Join Date: Sep 2007 Location: ...... Posts: 6,608 iTrader: (4)	They would be in the pluming section, if you can find someone ask where to find "hose barbs" and then just look around. If might help if you can cut a small piece of the hose off so that you can check the size. Good luck! Edit: They will probably be in a "T" shape and not a "Y' . Although it will still work.....

10-22-2007, 11:41 AM	#9
335ibob Enlisted Member Drives: 335i Join Date: Oct 2007 Location: SoCal Posts: 32 iTrader: (0)	Does anyone know the size of the stock "T" fitting for the vacuum hose? 1/8 or 3/16?

10-22-2007, 01:59 PM	#14
sambonator Samtaro! Drives: a car Join Date: May 2007 Location: Milky Way Galaxy Posts: 2,507 iTrader: (5)	Are the T's you get at hardware stores able to survive in the hot engine compartment? __________________

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search