[yas75]

HELLO
I explain
I have a 2009 BMW E90

FRM 2
I install BI-xenon LCI

everything works except the high beam shutter


I have created the cable from pin 5 to pin 6 or whatever you connect it to FRM 2
(X14260 connector)


therefore remains open

SOLUTIONS?

I am French desoler for fault

[yas75]

[yas75]

HELP ME

[E92-Lighting]

driver/ballast?

[yas75]

yes ballast

the shutter functions only when I of the current

between pine 5 and pine 3/pine 6

but remains to activate

[bmw325i]

It's pin 41

[yas75]

THANK YOU

But on the PDF he says

A6 / Eyelet /Terminal 31/To joint connector behind the right headlight /X166

And not 41 ???

[yas75]

Plz

Bi-xenon Pin 1 -----------frm 2 Pin ?
Bi-xenon Pin 2 -----------frm 2 Pin ?
Bi-xenon Pin 3 -----------frm 2 Pin ?
Bi-xenon Pin 4 -----------frm 2 Pin ?
Bi-xenon Pin 5 -----------frm 2 Pin ?
Bi-xenon Pin 6 -----------frm 2 Pin ?
Bi-xenon Pin 7 -----------frm 2 Pin ?

[bmw325i]

I've been trying to figure out the same. I don't have any wires for the headlight leveling though.

http://www.sparesdeals.com/index.php...product_id=667

http://www.sparesdeals.com/index.php...product_id=656

[yas75]

Bi-xenon Pin 1 -----------frm 2 Pin ?
Bi-xenon Pin 2 -----------frm 2 Pin ?
Bi-xenon Pin 3 -----------frm 2 Pin ?
Bi-xenon Pin 4 -----------frm 2 Pin ?
Bi-xenon Pin 5 -----------frm 2 Pin ?
Bi-xenon Pin 6 -----------frm 2 Pin ?
Bi-xenon Pin 7 -----------frm 2 Pin ?

[bmw325i]

Pin 1 -----------Angel eyes- Left: Plug X14261 Pin 41 / Right: Plug X14260 Pin 14
Pin 2 -----------Ground
Pin 3 -----------Low beam- Left: Plug X14260 Pin 6 / Right: Plug X14261 Pin 38
Pin 4 -----------Ground
Pin 5 -----------Shutter- Plug X14260 Pin 41
Pin 6 -----------High beam- Left Plug X14261 Pin 6 / Right: Plug X14260 Pin 4
Pin 7 -----------3 led's- Left: Plug X14261 Pin 50 / Right: Plug X14260 Pin 8
Pin 8 -----------Unused
Pin 9 -----------AHL- Plug X14260 Pin 42
Pin 10 -----------AHL- Left: Plug X14260 Pin 25 / Right Plug X14260 Pin 24
Pin 11 -----------Ground
Pin 12 -----------Turn Signals- Left:Plug X14260 Pin 13 / Right Plug X14261 Pin 40

[bmw325i]

Originally Posted by yas75

THANK YOU

But on the PDF he says

A6 / Eyelet /Terminal 31/To joint connector behind the right headlight /X166

And not 41 ???

That is for pin 2. A3/A4 which is pin 5 goes to A8 which is X14260 Pin 41 on the frm.

[yas75]

Thank you very much I am hopeless but could you draw a picture for me to understand(include) better

[bmw325i]

Originally Posted by yas75

Thank you very much I am hopeless but could you draw a picture for me to understand(include) better

Hopefully this will help. This is for adaptive lci xenons.

[yas75]

THANK YOU VERY MUCH really I am going to redo everything the cabling from tomorrow THANK YOU

I you yours informed

[yas75]

I can use a normal electric cable or not ?
or BMW

[bmw325i]

Originally Posted by yas75

I can use a normal electric cable or not ?
or BMW

What type of headlights did you have before and what are you trying to upgrade to?

Also I forgot to draw pin 3 on there, but it should stay the same.

[yas75]

I pass of halogen lighthouse(headlight) has bi xenon but high beam walks(works) not
To activate the shutter(sector)

Look at the photo of my car

[bmw325i]

Originally Posted by yas75

I pass of halogen lighthouse(headlight) has bi xenon but high beam walks(works) not
To activate the shutter(sector)

Look at the photo of my car

So have you done any wiring already? You need to connect pin 2 to ground and pin 5 to the frm X14260 Pin 41 and it should work. This is the harness you need.

http://www.sparesdeals.com/index.php...product_id=656

You can make your own harness, but if you want to get the autoleveling to work you'll need to buy the harness and leveling sensors.

[yas75]

my car and of 2009

[yas75]

Tomorrow I but a photo of my cabling

[bmw325i]

Originally Posted by yas75

my car and of 2009

The harness will still work for your car. You just need to follow the steps in the manual I posted.

The headlights are also from a 2009+ right? If they are, and you want the 3 led's to work, you'll need to run the wire from pin 7. You can use this kit to make the 3 led's work, or you can make your own harness for that as well.

http://www.sparesdeals.com/index.php...earch=retrofit