|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
Question on KW v3...
|
|
02-13-2013, 01:35 AM | #1 |
Lieutenant
34
Rep 497
Posts |
Question on KW v3...
Hey guys,
I have been running the recommended setting on the KW v3 since the first day I got my coilovers. And I am going to do a HPDE next month. Want to kind of adjust a little bit on my coilovers. After I read the manual from KW (not very detail in the manual tho), I understand the rebound rate which is adjusted on the top on the shock, and it is about the stiffness of the suspension. It can decrease the body roll at the high speed. But I still don't understand what the compression/bump which is adjust at the bottom of the shock is for.... Can someone explain it?? Please correct it if I am wrong, and if you guys would like, please share your KW v3 setting on the track! Thanks!! |
02-13-2013, 08:50 AM | #2 |
Brigadier General
1789
Rep 4,165
Posts
Drives: BMW M3
Join Date: Feb 2011
Location: PA, USA
|
The compression stroke is where the piston is going into the damper body, and rebound the opposite.
Damping is reducing the energy of motion to acceptable levels over a certain suspension travel distance, so that the forces acting on the car don't disturb handling or put excessive vertical loads on the car and driver. Compression damping controls the unsprung weight of the car (wheels/tires/brakes/half the suspension). The suspension will travel more than necessary if there's not enough of it, resulting in bad handling. Getting compression damping right is over and above more important than rebound for good handling. There needs to be just enough rebound damping to not convert more energy than necessary. Translated - too much rebound means the spring cannot extend itself quickly enough; the tire will not be in firm contact with the road. A tell for too much rebound damping is a rough ride where it feels as if you are being launched out of your seat going over a bump. On the track, too much rebound will result in the car feeling unstable under braking or entering corners, and a tendency to oversteer out of the corner. When adjusting a damper with more than one setting, make ONE adjustment at a time. I would start with both rebound and compression on full soft, and increase compression first. Go up a few clicks at a time, ride around the block, and keep doing that until you reach a point where the car feels good (each driver has a different preference, regarding suspension stiffness). Then adjust rebound and stop when you have a smooth ride. I imagine you won't go more than 1/4 - 1/2 the way towards stiff with rebound. My preference is to keep the rear suspension settings a few clicks softer than the front; there is some benefit to rear body roll (especially if you do not have an LSD).
__________________
2024 BMW M3 Sedan Frozen Pure Grey II/Fjord Blue, 6MT
Past: 2021 Z4 M40i Frozen Grey II/Black Alcantara | 2017 F30 340i Mineral Gray/Coral Red, 6MT | 2011 E92 335i Le Mans Blue/Black, 6MT |
Appreciate
0
|
02-13-2013, 09:42 AM | #3 | |
Lieutenant
69
Rep 404
Posts |
Wow, awesome post, thanks for sharing your knowledge!
Quote:
|
|
Appreciate
0
|
02-13-2013, 09:41 PM | #4 | |
Major
340
Rep 1,089
Posts |
Quote:
Well said and explained better than most I've seen. |
|
Appreciate
0
|
02-14-2013, 12:12 AM | #5 | |
Lieutenant
34
Rep 497
Posts |
Quote:
Thanks for your detail explanation!!! Sounds like it is easier to get the rebound rate right than the compression rate. Like you said, if I feel I am launched out from the seat, that means too over on the rebound. But how can I get to the right point of the compression rate?? |
|
Appreciate
0
|
02-14-2013, 12:23 AM | #6 | |
Evo Junkie
35
Rep 157
Posts |
Quote:
I normally adjust compression to the softest I can get away with in respect to travel and bump absorbance. I personally think in some applications, too much bump damping is used to compensate for too soft spring rates or anti-roll bars. |
|
Appreciate
0
|
02-14-2013, 09:41 AM | #7 | |
Brigadier General
1789
Rep 4,165
Posts
Drives: BMW M3
Join Date: Feb 2011
Location: PA, USA
|
You're welcome.
Quote:
Good compression damping prevents the unsprung weight from getting to higher velocities than desired; high unsprung weight velocities translate to bad handling. The damper should prevent the spring from absorbing more kinetic energy than necessary; and a well designed damper will counteract any suspension movement immediately, not after the fact. The most effective way to accomplish that is in the compression stroke. Regarding using bump damping as a compensation for spring rate (bump = compression for others joining in on this conversation) - depending on the damper, it's a valid way to add to the spring rate, especially in race classes where you can't change spring rates. High gas pressure dampers do so with great effect, and there's more benefit to high gas pressure than just assisting spring rate. Regardless, I concede there's no substitute for properly matched springs and dampers. I have doubts about race teams that can't calculate that correctly.
__________________
2024 BMW M3 Sedan Frozen Pure Grey II/Fjord Blue, 6MT
Past: 2021 Z4 M40i Frozen Grey II/Black Alcantara | 2017 F30 340i Mineral Gray/Coral Red, 6MT | 2011 E92 335i Le Mans Blue/Black, 6MT |
|
Appreciate
0
|
02-14-2013, 09:58 AM | #8 | |
Brigadier General
1789
Rep 4,165
Posts
Drives: BMW M3
Join Date: Feb 2011
Location: PA, USA
|
Quote:
Don't worry initially about 'getting it right' - the dampers are adjustable and you can adjust them at any time. I guarantee your preference will change over time. You won't know what is 'right' (and I say 'right' loosely because as I said, driver preference is key) until you try some settings, go with it for a while, then adjust them again (it's good idea to write the settings down in a notebook - be sure to note your tire model and tire pressures too). The same settings won't be ideal everywhere - e.g. really stiff on a smooth track is great but on the street ... nah. Sooner or later you'll understand the setting's effects, and neither I nor anyone else can give that experience to you in text form. Kind of like riding a bike. Good luck out on the track, be sure to tell us about it. There's usually a ton of knowledgeable and kind people at HPDE events (especially BMW CCA) - get a ride with someone and just have fun.
__________________
2024 BMW M3 Sedan Frozen Pure Grey II/Fjord Blue, 6MT
Past: 2021 Z4 M40i Frozen Grey II/Black Alcantara | 2017 F30 340i Mineral Gray/Coral Red, 6MT | 2011 E92 335i Le Mans Blue/Black, 6MT |
|
Appreciate
0
|
02-14-2013, 06:31 PM | #9 | |
Evo Junkie
35
Rep 157
Posts |
Quote:
Thus why 1 way dampers manufactured by Ohlins, Koni, KW, etc have the one adjustment alter the rebound damping with only a very slight effect on compression damping change. If compression damping was more important to get spot-on, this would be the main adjustment of a one way damper. I don't run the softest compression damping available, I run the softest I can get away with for my set-up and track, sprint or hill climb tarmac conditions. i.e. bump absorbsion without compromising grip. It's worked for me for the last 30 years of competing and track work. |
|
Appreciate
0
|
02-14-2013, 07:04 PM | #10 | |
Brigadier General
1789
Rep 4,165
Posts
Drives: BMW M3
Join Date: Feb 2011
Location: PA, USA
|
Quote:
__________________
2024 BMW M3 Sedan Frozen Pure Grey II/Fjord Blue, 6MT
Past: 2021 Z4 M40i Frozen Grey II/Black Alcantara | 2017 F30 340i Mineral Gray/Coral Red, 6MT | 2011 E92 335i Le Mans Blue/Black, 6MT |
|
Appreciate
0
|
02-14-2013, 11:21 PM | #12 | |
Brigadier General
1789
Rep 4,165
Posts
Drives: BMW M3
Join Date: Feb 2011
Location: PA, USA
|
Quote:
But getting it just right makes a lot of sense. The correct rebound setting range would seem to be rather narrow. Good to know, as I have a double adjustable damper set on order (time to re-learn the car I suppose).
__________________
2024 BMW M3 Sedan Frozen Pure Grey II/Fjord Blue, 6MT
Past: 2021 Z4 M40i Frozen Grey II/Black Alcantara | 2017 F30 340i Mineral Gray/Coral Red, 6MT | 2011 E92 335i Le Mans Blue/Black, 6MT |
|
Appreciate
0
|
02-15-2013, 02:07 AM | #13 |
Lieutenant
34
Rep 497
Posts |
One more question. I read the manual from KW, "Before performing any adjustments, the valve must be closed by turning the adjuster in the full clockwise direction. In this position, the shock will be at full hard, or “maximum power”." Does that mean every single time I adjust the V3, I have to turn it to full hard before I start adjusting or I will damage it??
|
Appreciate
0
|
02-15-2013, 02:21 AM | #14 | |
Colonel
164
Rep 2,556
Posts |
Quote:
thx for the informative posts btw
__________________
2007 E90 335i, TiAg, 6AT, ZPP, ZSP, ZCW, 6FL, HD
Quaife lsd, ETS fmic, GIAC s/w, Dinan intake/exhaust/oc, Koni/M3 susp, Apex Arc 8, Mich PSS |
|
Appreciate
0
|
02-15-2013, 07:49 AM | #15 | ||
Brigadier General
1789
Rep 4,165
Posts
Drives: BMW M3
Join Date: Feb 2011
Location: PA, USA
|
Quote:
Quote:
I'm planning to sell my RS1 setup (inc. springs/camber plates) when the new setup gets installed - drop me a PM.
__________________
2024 BMW M3 Sedan Frozen Pure Grey II/Fjord Blue, 6MT
Past: 2021 Z4 M40i Frozen Grey II/Black Alcantara | 2017 F30 340i Mineral Gray/Coral Red, 6MT | 2011 E92 335i Le Mans Blue/Black, 6MT |
||
Appreciate
0
|
02-15-2013, 04:02 PM | #16 | |
Evo Junkie
35
Rep 157
Posts |
Quote:
|
|
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|