|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
Instrument Cluster Swap Question
|
|
01-11-2017, 07:42 AM | #45 |
Captain
253
Rep 775
Posts |
Looks like it's on the back. And while I can't find a close up of the CPU, it looks pretty similar:
Even if you don't have convenient vias to solder to, you could solder straight to the CPU (though you'd have to be careful since all the points are next to each other) |
Appreciate
0
|
01-11-2017, 05:58 PM | #46 | |
Major
808
Rep 1,192
Posts |
Quote:
It is very strange though. Even with this known good Eeprom content, the cluster always stays with one DTC: 9317 EEPROM: Fehler Codierdaten BMW unplausibles Signal oder Wert Testbedingungen erfüllt Fehler momentan vorhanden und bereits gespeichert Fehler würde kein Aufleuchten einer Warnlampe verursachen Error code: 93 17 68 I can write my VIN to it and the tamper dot goes away. But when I try to read (or write) coding data with NCSexpert, I get always this error message: [10:17:26.214] [2017-01-10] [SERIE] 2062 PABD/CABD A_PL2KMB.IPS Cod 391 [10:17:26.214] [2017-01-10] [SERIE] Fehler beim Codierdaten lesen KOMB87, C_C_LESEN: ERROR_ECU_UPLOAD_NOT_ACCEPTED [10:17:26.319] [2017-01-10] [SERIE] 2062 Error COAPI2.CPP coapiRunCabd 6 [10:17:26.319] [2017-01-10] [SERIE] Fehler beim Codierdaten lesen CODIERDATEN_LESEN A nettodat coding goes through without problems, but as soon as I code it either with Nettodat or empty FSW_PSW.MAN, I get this message on the CIC: "Speedometer display malfunction". Yet the speedometer works fine, in Ediabas and while driving. The rpm gauge stays at 0 (except shortly after reset with engine running). All gauges work flawlessly with Ediabas steuern_xxx. Any ideas? |
|
Appreciate
0
|
01-11-2017, 08:40 PM | #48 | ||
Lieutenant
36
Rep 400
Posts |
Quote:
|
||
Appreciate
0
|
01-12-2017, 07:19 AM | #50 | |
Major
808
Rep 1,192
Posts |
Quote:
The cluster is from a 2007 E92 328xi with the ZB number 9168354. I’m trying to retrofit it into a 2011 E90 335d. My cluster’s ZB number is 9242376. Both point to the same program file 9316169A.opa in HKOML2, except that my ZB number updates to the newest ZB nr 9316157 and the E92 updates to the ZB nr 9316151. I also tried force feeding the ZB 9242370 of a 2011 E92 (file 9242396A.0pa) via WinKFP expert mode. All flashes went without problems but the EEprom corruption DTC persists. I did physically replace the original EEprom but I’m sure the connections are all good since I can write to the gauge sections with Ediabas just fine. Any other suggestions? Your help is greatly appreciated. |
|
Appreciate
0
|
01-13-2017, 05:50 AM | #52 | |
Major
808
Rep 1,192
Posts |
Quote:
Reading back EEprom confirms that content is exactly the same as the file written to it. I always do that in addition to the automatic verify the xprog. |
|
Appreciate
0
|
01-13-2017, 08:06 AM | #53 | |
Ballin' out of control.
523
Rep 1,289
Posts |
Quote:
Have you tried flashing the donor cluster with ZB number 9242376? The reason I ask is because unlike the petrol kombi high firmware releases which are qualified across multiple chassis types, ZB number 9242376 was exclusively qualified for the US 335d 09/08-11/11.
__________________
Alpina B3 Flash/BMS OCC/ER CP/ETS 5/HKS BOV/M3 Control Arms
|
|
01-13-2017, 12:58 PM | #54 | |
Terorist!
29
Rep 315
Posts |
Quote:
you want petrol cluster to fit on diesel car?!?!?!?
__________________
E90/320d/163cp/2007/black/retofit LCI front/rear/Mtech/style 162/M3 mirrors/auto dimming mirrors int-ext/EIBACH PRO KIT/M3spoiler/Performance Kidney Grills/MT/shadow line/M shift knop/M3 steering wheel cover/M footrest/M door sills/M handbrake/Performance aluminium pedal pads/sunroof
___________(Oo) (|||) o (|||) (oO)____________ |
|
Appreciate
0
|
01-13-2017, 01:08 PM | #55 | ||
Major
413
Rep 1,362
Posts |
Quote:
__________________
|
||
Appreciate
0
|
01-13-2017, 02:17 PM | #56 | |||
Colonel
532
Rep 2,503
Posts |
Quote:
Have you tried coding the KOMBI with a fake date in FA? Change FA to date of retrofitted cluster but DO not FA_WRITE. Then go back and code KOMBI to default with expert mode and SG_CODIEREN. |
|||
Appreciate
1
Mik325tds808.00 |
01-14-2017, 02:02 AM | #57 |
Lieutenant
36
Rep 400
Posts |
My cluster is from a E92 335d LCI and my car is a E91 320d non-lci and I got no errors. Could not be that.
Are you sure your "new" cluster is from a 328? Rpm gauge is marked at 8000rpm? |
Appreciate
0
|
01-14-2017, 09:00 AM | #58 | |
Major
808
Rep 1,192
Posts |
Quote:
I find that very strange though. In the history file all ZB numbers 9242376 (your suggested), 9242396 (my current) and 9168354 (the donor cluster original) all point to the same newest update file 9316169A.opa. Why wouldn't the donor work with that? Also, you are right that they both share the same physical hardware number, 6966737. But when I opened up mine to pull the EEprom data, I noticed that the EEprom was turned 90 degrees in comparison to the donor cluster. How can the be the same HW number? Usually, if a supplier does a change like that, the HW number changes as well. Anyway, thousand thanks to you 808AWD325xi and Sensible_ for your help! You wouldn't know by any chance what the coding would be to display coolant temp on the oiltemp/KVA gauge? |
|
01-14-2017, 11:45 PM | #59 | |
Major
413
Rep 1,362
Posts |
Quote:
The problem is Pre lci to lci. In 5 Series case, cruise control error if u put a Pre lci on a lci.
__________________
|
|
Appreciate
1
FKingBear3.50 |
01-15-2017, 12:10 PM | #60 | |
Ballin' out of control.
523
Rep 1,289
Posts |
Quote:
With regards to the program data sets (.0pa), each of the ZB numbers in this case actually reference a different .0pa file: 2007 E92 328xi donor ZB number 9168354 --> 9168320A.0pa 2011 E90 335d original ZB number 9242376 --> 9242396A.0pa If you have the SP daten that includes a given ZB number, view the .DAT file to determine the corresponding program data set. For example, HKOML2.DAT: Code:
;ZB-NR TYP-NR HW-NR IX SW-NR AM PIN S CS [...] 9242376,0000000,9242396,A,0000000DA,0FFFFFFFFFD,000,1 4 [...] Code:
;ZB-NR TYP-NR HW-NR IX SW-NR AM PIN S CS [...] 9316157,0000000,9316169,A,0000000DA,0FFFFFFFFFD,000,1 R [...] http://www.realoem.com/bmw/enUS/part...2-10-9-316-157 I believe that physical hardware numbers only change when there is a material change which impacts firmware compatibility.
__________________
Alpina B3 Flash/BMS OCC/ER CP/ETS 5/HKS BOV/M3 Control Arms
|
|
Appreciate
1
Mik325tds808.00 |
01-19-2017, 04:15 PM | #61 |
First Lieutenant
46
Rep 369
Posts |
|
Appreciate
0
|
01-28-2017, 11:05 AM | #62 |
Private First Class
35
Rep 177
Posts |
Has anyone successfully done this with a MiniPro TL866CS (there is also a TL866A) programmer and SOP 8 clip?
I have the TL866CS and it's giving me an over current error...
__________________
Monaco Blue E92 // BMS JB4 G5 ISO // BMS Backend Flash // Dual Cone Intake // ER Chargepipe // Dual HKS SSQV BOV Setup // BMW Performance Spoiler // 19" v710 Dolphin Grey // Aero Front Lip // M3 Sideskirts // Mtech Rear Bumper // Quad Tip Diffuser // Quad Exhaust // |
Appreciate
0
|
02-01-2017, 11:38 PM | #64 | |
Private
9
Rep 64
Posts |
Quote:
http://www.bimmerfest.com/forums/sho...46&postcount=9 |
|
Appreciate
0
|
07-20-2017, 06:13 AM | #65 |
New Member
0
Rep 5
Posts |
eeprom upload error
bumping this one if anyone can help,
have 07 m3 cluster to retro fit to 06 335i, miles and vin are correct but when I try to code i get these 2 errors: 2060 PABD/CABD A_PL2KMB.IPS COD 371 coding erroneous (general) KOMB87, C_C_AUFTRAG: ERROR_ECU_UPLOAD_NOT_ACCEPTED. and 2060 Error COAPI2.CPP coapiruncabd 6 coding erroneous (general) sg_coderian with i drive error "speedometer display faulty" can anyone help? |
Appreciate
0
|
05-13-2018, 06:27 AM | #66 |
New Member
3
Rep 16
Posts |
can i take off old eeprom from old cluster and put it on the new cluster this will fix the problem and my vin will be ok and milage even if they are deffrant kinds of eeprom pls hlp
|
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|