|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
Instrument Cluster Swap Question
|
|
02-08-2016, 04:50 AM | #23 |
First Lieutenant
24
Rep 355
Posts |
Again, sorry, no.
To get to the circuit board, the dial face has to be removed, means removing the needles.. It is easy to calibrate them later.. Just make sure you remove them carefully.. To calibrate, Fire up INPA, go to Kassorie-> Instrument Cluster.. And F6 activate. Enter 0 for set speedo, and set it to 0.. You should be fine.
__________________
In Progress: Surround View Retrofit 8TH |
Appreciate
0
|
02-17-2016, 01:15 AM | #25 |
Terorist!
29
Rep 315
Posts |
Hello.....a few month ago I changed my standard cluster on a 320d with HIGH cluster.see picture
ok....I changed the orange led with white (home made), but to change eeprom was necessary to pay someone. I never programmed an eeprom, and I have no ideas about that....I purchased an MiniPro TL866CS. I know I have to modify VIN and mileage in eeprom, but I have no idea what I have to change. Can anyone explain more detailied about that procedure? Thank you
__________________
E90/320d/163cp/2007/black/retofit LCI front/rear/Mtech/style 162/M3 mirrors/auto dimming mirrors int-ext/EIBACH PRO KIT/M3spoiler/Performance Kidney Grills/MT/shadow line/M shift knop/M3 steering wheel cover/M footrest/M door sills/M handbrake/Performance aluminium pedal pads/sunroof
___________(Oo) (|||) o (|||) (oO)____________ |
Appreciate
0
|
02-17-2016, 04:02 AM | #27 |
First Lieutenant
24
Rep 355
Posts |
Quote:
http://www.bimmerfest.com/forums/sho...d.php?t=666729 I just posted it in the last page..
__________________
In Progress: Surround View Retrofit 8TH |
Appreciate
0
|
02-17-2016, 05:14 AM | #28 | |
Terorist!
29
Rep 315
Posts |
Quote:
__________________
E90/320d/163cp/2007/black/retofit LCI front/rear/Mtech/style 162/M3 mirrors/auto dimming mirrors int-ext/EIBACH PRO KIT/M3spoiler/Performance Kidney Grills/MT/shadow line/M shift knop/M3 steering wheel cover/M footrest/M door sills/M handbrake/Performance aluminium pedal pads/sunroof
___________(Oo) (|||) o (|||) (oO)____________ |
|
Appreciate
0
|
10-24-2016, 08:41 AM | #29 | |
Private First Class
14
Rep 144
Posts |
Quote:
thankyou for your precious information on writing eeprom using a programmer. just want to confirm if a chip can be read or written without desoldering? if i use the clip on the chip with the board the power should be supplied to other chips as well. do you know any impact on writing or reading? it should not be a big deal? i really want to do the programming with what you suggested as the soldering may lead to other risks. thanks//sono Last edited by sono0312; 10-24-2016 at 08:51 AM.. |
|
Appreciate
0
|
10-24-2016, 07:37 PM | #30 | ||
Colonel
532
Rep 2,503
Posts |
Quote:
|
||
Appreciate
1
sono031213.50 |
10-24-2016, 10:33 PM | #31 |
BimECU
191
Rep 759
Posts |
btw had problem with e60 cluster with my R270
it reads and erases V6 fine but on E60 (M35080 6) freezes on reading 33/1024 :/ |
Appreciate
0
|
11-05-2016, 09:31 PM | #32 | |
Private First Class
14
Rep 144
Posts |
Quote:
when it comes to a used instrument cluster, what we need is erase both milage and vin in order to make it virgin. by using r270+, i learned that oddometer can be erased by using tool function (read/write by seletcting proper eeprom). however what does it need to be done for vin? some thread says that datum in dump list, line 0x002e0 have to be changed to FF... i am just wondering if vin can be changed as ussual by usng tool like winkfp? |
|
Appreciate
0
|
11-05-2016, 11:08 PM | #33 | ||
Colonel
532
Rep 2,503
Posts |
Quote:
|
||
Appreciate
0
|
11-07-2016, 04:14 PM | #34 | |
Private First Class
14
Rep 144
Posts |
Quote:
I hope r270+ will erase both vin (all to "ff") and odo (all to "00") by one-click button. Is it correct? Or i need to change them one-by-one? |
|
Appreciate
0
|
11-07-2016, 04:16 PM | #35 | ||
Colonel
532
Rep 2,503
Posts |
Quote:
Instead you may need to read the complete eeprom. Modify with hex editor then write back eeprom... |
||
Appreciate
0
|
11-07-2016, 07:10 PM | #36 | |
Private First Class
14
Rep 144
Posts |
Quote:
i found where to change from other threads. all i need is change hex data as follows... are these correct? odo: change all "00" from 0x00000 to 0x0001F vin: change all "ff" from 0x002e9 to 0x002ef those may applicable only to e9x 3 series. |
|
Appreciate
0
|
11-09-2016, 11:16 PM | #38 | ||
Colonel
532
Rep 2,503
Posts |
Quote:
Also, of after changing mileage to all 00 bytes mileage is not 0, change byte at 0x2D7 to 00 also. Always test before plugging into car by connecting 12v +/- power to pin 9 and 18. Then press odo button on KOMBI to display mileage. |
||
Appreciate
1
DaZuc204.00 |
01-09-2017, 06:47 PM | #39 |
Major
808
Rep 1,192
Posts |
|
Appreciate
0
|
01-09-2017, 10:59 PM | #40 | |
Colonel
532
Rep 2,503
Posts |
Quote:
All I know is that if that byte is not 00, odo reading will not be 0. |
|
Appreciate
0
|
01-10-2017, 05:39 AM | #41 | |
Major
808
Rep 1,192
Posts |
Quote:
I think my original EEprom read was corrupted. I replaced it with a new one, fixed my xbox and wrote FF to Vin plus the 00 to 0x2D7. However, I'm getting the coding error and it would not accept a VIN upload or coding uploads. Strange though: Nettodata write and Ediabas c_c_schreiben works. Do you have a good EEprom read by any chance that I can transfer into mine? |
|
Appreciate
0
|
01-10-2017, 04:41 PM | #42 | ||
Colonel
532
Rep 2,503
Posts |
Quote:
https://drive.google.com/open?id=0B0...0RzaHRHbnJRa2c |
||
Appreciate
1
Mik325tds808.00 |
01-10-2017, 05:36 PM | #43 |
Captain
253
Rep 775
Posts |
|
Appreciate
0
|
01-10-2017, 10:08 PM | #44 |
BimECU
191
Rep 759
Posts |
it should be same, and it would save lots of hassle with this needles,
I'm always afraid to break them plus my programmer(VVDI PROG) does not like working with clip, need to desolder/solder all the time but dont you have to remove needles to get to processor anyways? |
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|