|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
2E82 code--electric coolant pump-shutdown
|
|
10-21-2011, 03:53 PM | #1 |
Private
15
Rep 69
Posts |
2E82 code--electric coolant pump-shutdown
anyone had this? how long before pump goes? i believe this explains why my aux fan runs high a few minutes after startup. it will go away if i shutdown and startup again and sometimes just stop on its own. also, when I shutdown car I have been hearing a whrrring/winding sound.
anyway, anyone else have this code? |
10-21-2011, 05:18 PM | #2 |
Major
64
Rep 1,087
Posts
Drives: 2006 BMW 325i
Join Date: Apr 2011
Location: Hot Springs, AR
|
SI B12 04 05
Engine Electrical Systems October 2008 Technical Service This Service Information bulletin supersedes SI B12 04 05 July 2007. [NEW] designates changes to this revision SUBJECT Check Engine Lamp Illuminated and/or Vehicle Overheats MODEL [NEW] E83 (X3) with N52K engine [NEW] E85 and E86 (Z4) with N52 engine [NEW] E70 (X5) with N52K engine [NEW] E90, E91, E92 and E93 (3 Series) with N51, N52 and N52K engines [NEW] E60 and E61 (5 Series) with N52 and N52K engine [NEW] All models above produced up to December 31st, 2006 SITUATION The customer complains that the Check Engine lamp is illuminated and/or that the vehicle overheated. One or more of the following fault codes is stored in the DME: FC 2E81 Electric coolant pump, speed deviation, speed outside the tolerance FC 2E82 Electric coolant pump cutoff, over-current FC 2E83 Electric coolant pump, power-reduced operation, dry run FC 2E84 Electric coolant pump, communication FC 2E85 Electric coolant pump, communication, no voltage at emergency operation input of pump CAUSE One of the following can be the cause: - Insufficient power supply - Insufficient grounding - BSD signal not present - Defective electric coolant water pump - Electric coolant pump water pump processor disturbance PROCEDURE A This procedure only applies to vehicles produced after September 1, 2005. Both faults must be stored; if any other combination of the faults is stored, refer to procedure B. - FC 2E81 Electric coolant pump, speed deviation, speed outside the tolerance - FC 2E85 Electric coolant pump, communication, no voltage at emergency operation input of pump 1. Remove both battery cables from the battery for 15 minutes . 2. After reconnecting the battery cables, clear the vehicle fault memory and ensure that the electric coolant pump operates using the bleeding procedure, described at the end of this bulletin. PROCEDURE B This procedure applies to all vehicles with any combination of faults listed below. FC 2E81 Electric coolant pump, speed deviation, speed outside the tolerance FC 2E82 Electric coolant pump cutoff, over-current FC 2E83 Electric coolant pump, power-reduced operation, dry run FC 2E84 Electric coolant pump, communication FC 2E85 Electric coolant pump, communication, no voltage at emergency operation input of pump NOTE: All measurements should be performed with the battery charger connected to the vehicle. 1. Measure the following at connector X6035 on the electric coolant water pump: - E90 and E91 - Pin 1 (fuse F09) and Pin 4 ground (X6455) = 12 volts - E60 and E61 - Pin 1 (fuse F23 and Pin 4 ground (X6455) = 12 volts - Pin 2 (fuse F02) and Pin 4 ground (X6455) = 12 volts - Pin 3 BSD signal (DME Pin 26) and Pin 4 ground (X6455) = 7.5 - 8.5 volts - If any of the above measurements are incorrect, continue troubleshooting using the DIS Plus or GT1 to determine the source of the problem. - If all of the above measurements are correct, proceed to step 2. 2. Replace the electric coolant water pump (PN 11 51 7 546 994) in accordance with Repair Instruction RA 11 51 000. 3. After performing any service work requiring draining of the coolant, the system must be bled to ensure that there are no air pockets present. The system can be bled using the DISplus/GT-1 or by following a special procedure. To bleed the system, follow the procedure described at the end of this bulletin. BLEEDING (VENTING) THE COOLING SYSTEM NOTE: BMW recommends filling the cooling system for protection against freezing down to -34 degrees F (-37 degrees C) ; this is an antifreeze ratio of 50% antifreeze and 50% water. In severely cold areas, the antifreeze can be increased to 60%, which provides freezing protection down to -62 degrees F (-52 degrees C) . Do not exceed a 60% ratio of antifreeze. The specified antifreeze ratio is important, since an insufficient amount would impair antifreezing and corrosion-inhibiting protection. An excessive amount would not improve freezing protection, but would instead reduce freezing protection. At all times, the antifreeze and water should be premixed before pouring into the engine. If premixing is not performed, damage will occur to the water pump assembly. NOTE: Always connect a battery charger while performing the bleeding process. 1. Fill the system with coolant via the expansion tank (AGB). Top up the coolant level to the lower edge of the expansion tank. 2. Close the expansion tank. 3. Switch on the ignition. 4. Set heating to the maximum (temperature); switch on the blower (lowest stage). 5. Press the accelerator pedal module to the floor for at least 10 seconds . The engine must NOT be started. 6. Bleeding via EWP takes approximately 12 minutes . Then check the coolant level in the expansion tank; top up to the MAX marking if necessary. 7. Check the cooling circuit and drain the plugs for leaks. 8. If the procedure needs to be repeated several times, allow the DME to completely de-energize (remove the ignition key for approx. 3 minutes ) and then repeat the procedure, starting from item 3. Read more: scanned a 2006 525xi and codes 2ef5,2e81,2a82,2e82 present have - JustAnswer http://www.justanswer.com/bmw/2ds7s-...#ixzz1bSPt36Zs |
Appreciate
1
Phyrexia506.00 |
10-22-2011, 04:30 PM | #3 |
Some dude
92
Rep 1,780
Posts |
Schedule a time to get the water pump, bolt set, and thermostat replaced at your local independent mechanic. I've done several lately. Flush and refill the coolant, and reset the CBS for the coolant.
__________________
RRT
E92 335i/6MT with stuff and things |
Appreciate
0
|
10-23-2011, 11:21 AM | #4 |
Private First Class
23
Rep 124
Posts |
^ x2 we had 3 E90s in for the same thing on Friday. Did about 5 last week, I'm hoping mine doesn't decide to take a crap for atleast a few more months.
|
Appreciate
0
|
10-23-2011, 02:46 PM | #5 |
Private
15
Rep 69
Posts |
what would you say if i told you a couple of weeks ago I brought it to my indie mech and he said i needed a whole new fan. so I paid 800 bucks for this misdiagnosis. it appears he didnt even check for codes
|
Appreciate
0
|
10-04-2012, 09:02 AM | #7 |
Captain
144
Rep 932
Posts |
Same problem on my 335i 2007 after 74.000km
Water pump dead Engine FAN always on. Error found 2E81, 2E82 Unknow the causes.
__________________
BMW F82 M4 Black MHD CS Map - GTS DKG - Navi -Performance Brake RSL1 Pads - USB - DivX-DVD - Bluetooth - VoiceControl - Connect - Apps - Online - H&K - TrafficInfo - SpLimInfo - WhiteMerino- PDC - Cam - Adaptive Led - Antitheft - CP Steering- Performance ST - Adaptive CP Setup - GarageDoorOpen - Pipercross - Stock Exhaust - Mdrivers Pack - 437M Wheels
|
Appreciate
0
|
11-21-2012, 11:27 AM | #8 |
BMW Fan
148
Rep 314
Posts |
|
Appreciate
0
|
11-21-2012, 02:42 PM | #9 |
Captain
144
Rep 932
Posts |
700 euro.
New water pump and new thermostat All components are news and installed by BMW last month.
__________________
BMW F82 M4 Black MHD CS Map - GTS DKG - Navi -Performance Brake RSL1 Pads - USB - DivX-DVD - Bluetooth - VoiceControl - Connect - Apps - Online - H&K - TrafficInfo - SpLimInfo - WhiteMerino- PDC - Cam - Adaptive Led - Antitheft - CP Steering- Performance ST - Adaptive CP Setup - GarageDoorOpen - Pipercross - Stock Exhaust - Mdrivers Pack - 437M Wheels
|
Appreciate
0
|
11-21-2012, 10:02 PM | #10 |
Colonel
719
Rep 2,610
Posts
Drives: 06 330i E90, 18 530xe G30
Join Date: Dec 2010
Location: Toronto
|
I just DIY'd this yesterday, new stat, pump and coolant. Also did the bleed proceedure. Do I need to reset anything on the ECU before I use it? I don't have a code reader....
|
Appreciate
0
|
11-23-2012, 09:50 AM | #11 | |
Captain
44
Rep 642
Posts |
Quote:
If your fan is always going, I dunno how that equates to needing a new fan. It shutting down is normal depending on the coolant temp. There are things that you might have to kinda guess, but I don't think this was one of them. Last edited by Casca; 11-23-2012 at 10:02 AM.. |
|
Appreciate
0
|
05-30-2018, 12:21 PM | #12 |
Registered
0
Rep 2
Posts |
My 2007 335i coupe sport 126,000 miles, went into limp home mode. No temperature gauge, so first indication was yellow thermometer followed quickly by red. Was traveling on highway at about 70 - 80. Was fortunate that I was near an exit. Called for tow, 40 miles or so to my local BMW dealer. Fixed in 1/2 a day, cost about $1600. half for parts the rest labor. Dealer said this pump is now "covered" for vehicle lifetime.
|
Appreciate
0
|
02-04-2019, 09:40 AM | #13 |
Private
10
Rep 71
Posts |
FC 2E81 Electric coolant pump, speed deviation, speed outside the tolerance
FC 2E82 Electric coolant pump cutoff, over-current I do have these 2 codes and my fan does go on and will go into limp mode if i keep it running... however if i turn the engine on and off quickly it goes back to normal.. |
Appreciate
0
|
02-04-2019, 11:55 AM | #14 |
Save the manuals!
6053
Rep 6,758
Posts |
That's because your pump is dying. Change it out before you're stranded roadside.
__________________
'16 M3 | '23 718 Spyder Past: E92 M3, F87 M2, E39 M5, etc |
Appreciate
0
|
02-04-2019, 01:35 PM | #15 | |
Resident Pedant
506
Rep 792
Posts |
I suggest you read the giant post by Johnny B that explains exactly what to do.
Quote:
__________________
'15 F30 335i 8AT Estoril II/Black (12.218 @ 114.94mph)
MHD Stage 2+ 93 / XHP Stage 3 / M-Goodies / K&N Filter / ER CP / CSF IC / NGK 97506 / ER DP / Michelin A/S 3+ |
|
Appreciate
0
|
08-19-2019, 09:03 PM | #16 | |
New Member
2
Rep 20
Posts |
Quote:
|
|
Appreciate
0
|
10-07-2019, 04:23 PM | #17 |
New Member
2
Rep 16
Posts |
I have the same issue with this code. Plugged in OBD deleted these 2 codes and water pump doesn't run anymore. Before that, the pump was fine, I've been driving for like 30-40minutes with these codes. Now I'm getting 2e82 code, trying to delete it but it instatly pops up again. Fan is working on max speed, returning coolant line to the reservoir is cold.
|
Appreciate
0
|
10-08-2019, 04:25 PM | #19 | |
General
18717
Rep 19,444
Posts |
Quote:
There are hundreds of threads on E90 Post regarding failed water pumps. Search and educate yourself on the subject. Search on Eninty, he made a good thread on the subject and posted a DIY on how to replace the pump. Good luck with the repair. |
|
Appreciate
0
|
Bookmarks |
|
|