|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
DIY: How to setup BMW Standard Tools 2.12 w/Windows 10 x64 (64-bit)
|
|
05-30-2016, 02:06 PM | #89 |
997.1TT
1017
Rep 1,672
Posts |
While it works intermittently, it is annoying that it won't connect to the car the majority of the time, so I am returning the cable i bought and I bought the One Stop Electronics cable. Hopefully I will have better luck with it. If nothing else, atleast then I can narrow my issue down to the software install, or the car itself (least likely).
__________________
Current: 2007 Porsche 911 Turbo Former: ESS Supercharged ///M3 Interlagos Blue ZCP Subscribe to YouTube: https://www.youtube.com/c/Rat3dM Follow me on Instagram: https://www.instagram.com/rat3d_m/ |
Appreciate
0
|
06-04-2016, 02:47 PM | #90 | ||
New Member
3
Rep 12
Posts |
Well, I got as far as...
Quote:
Quote:
Any tips on where to go from here? |
||
Appreciate
0
|
06-04-2016, 03:00 PM | #91 |
New Member
3
Rep 12
Posts |
Strike that. I wasn't running cmd as an administrator. I corrected that mistake, and it worked fine.
|
Appreciate
0
|
06-05-2016, 07:00 PM | #92 | |
New Member
0
Rep 6
Posts |
I think i'm missing something little here or I pulled a stupid but here's where i'm getting stuck.
Quote:
When I went to the device manager and found the cable under the COM & LPT it was originally listed under COM4 - rather than 3 (didn't figure it was a big deal... but maybe it was?). I changed both options as the guide suggested so that it now is under COM1. However, it doesn't show up in the install options. It is plugged into the same USB port it was initially as well. Have you seen this before? Otherwise (and I know i'm late to the party, but) this is an absolutely awesome write up, it's because of people like you in the community that i've been able to work on my car as much as I have and enjoy my car so much. THANK YOU! |
|
Appreciate
0
|
06-05-2016, 08:15 PM | #93 | |
New Member
3
Rep 12
Posts |
Quote:
Code:
[OBD] Port=Com3 Hardware=USB Code:
;################# ;# EDIABAS 7.3.0 # ;################# ;============================================================================= [Configuration] ;============================================================================= Interface =STD:OBD Simulation = 0 |
|
Appreciate
0
|
06-05-2016, 08:23 PM | #94 |
New Member
0
Rep 6
Posts |
Thank you. Apparently i'm just being to dense and only trying to follow the directions specifically. If I had just clicked next again it would have worked.
Thanks for the help |
Appreciate
0
|
06-17-2016, 09:30 AM | #95 |
Lieutenant Colonel
473
Rep 1,913
Posts |
First time setting up BMW Standard Tools and am getting this error while trying to register the WinKFP-NFS folder... I've double checked the folder name and copied a fresh version into C:. A little help?
__________________
'09 335D
|
Appreciate
0
|
06-17-2016, 11:44 AM | #96 |
Ballin' out of control.
523
Rep 1,289
Posts |
This DIY does not utilize third party tools such as BMW coding tool. Perhaps you posted to the wrong thread?
__________________
Alpina B3 Flash/BMS OCC/ER CP/ETS 5/HKS BOV/M3 Control Arms
|
Appreciate
0
|
07-04-2016, 09:13 PM | #98 |
First Lieutenant
150
Rep 331
Posts |
Would it be fair to say coding e90 takes much more effort than needed for F-series.
I can code F-series and now I'm looking into learning how to code e90's, but it seems like it's way more complicated. I use my daily laptop to code F-series, but it seems like I would have to buy a device solely to code e90's, is this true. Thanks. Last edited by bizfiend; 07-04-2016 at 09:19 PM.. |
Appreciate
0
|
07-05-2016, 09:03 AM | #99 | |
Ballin' out of control.
523
Rep 1,289
Posts |
Quote:
Neither chassis family is difficult to code. The main difference is that newer tools like E-Sys have an improved GUI as opposed to BMW Standard Tools which is significantly older and not as intuitive.
__________________
Alpina B3 Flash/BMS OCC/ER CP/ETS 5/HKS BOV/M3 Control Arms
|
|
Appreciate
0
|
08-04-2016, 08:59 PM | #100 |
New Member
0
Rep 11
Posts |
I received an error when on 02_Step_2 along the lines of "foreign application responded to a DDE initiate". After windows updates and installing .NET Framework 3.5 and rebooting this started functioning.
I am unsure of which one was the resolution but I suggest getting fully updated and installing .NET 3.5 before starting this procedure. I also went through the same steps after the rebuild. |
Appreciate
0
|
09-29-2016, 11:27 PM | #101 |
New Member
0
Rep 6
Posts |
I got everything installed correctly and looked up my I-level, and it is a version that's not even on that chart -- I assume this means it hasn't been updated since it was built in 2009.
Are there any benefits from updating some or all of the modules? I have the newest SP-Daten. |
Appreciate
0
|
09-30-2016, 08:34 AM | #102 |
Registered
0
Rep 2
Posts |
Good stuff from 808AWD325xi - Thank you! Now, can someone tell the size of USB needed for this? Anyone did this so far? - ~ I'm using windows 7 but seem to flow ok! (Activating the link given SP-Daten alone takes a monstrous amount of 15.58GB when trying to download through MEGA.) I'm heading for 64 gigabytes if no replies |
Appreciate
0
|
10-04-2016, 04:04 PM | #103 |
Private First Class
30
Rep 106
Posts |
Wondering if you can help. I took a round-about way of installing things. I already had INPA 5.0.6 up and running w/Standard Tools 2.12 - The issue is that once I fired up INPA and got past the initial vehicle select, all menus were in German.
I assumed that I didn't have the correct eng translations, and came here to see how to extract them from 5.0.2 and update. Unfortunately, I couldn't get the download you provided to work, but I was able to obtain 5.0.2 and all associated tools. I was able to follow along, although the folder structures of the install I downloaded were a bit different. Regardless all processes went smoothly. I did the install of 5.0.2 on an XP VM and got what I needed from there. The issue presents itself now with the Win10 install. Once I run INPA, instead of what used to be Shift F2 for e90it is now Shift F3 (not a big deal). Past that point, menus are in english (WINNING!) The problem is if i go to Engine, MSD80 for N54 is not listed. I have copied over all the CFGDAT and SGDAT info, but don't see my engine listed. Previously running 5.0.6 it was in there and I could connect, it was just in German. Any thoughts or ideas to point me in the right direction? EDIT: Ran old installer in repair mode and got back all options. The Caveat is that now the secondary menus after selecting MSD80 N54 are once again in German. Can you give me a brief over view of how to fix that? Or what files I need to be extracting from the 5.0.2 install to update to English? Thanks! Thanks! Last edited by milfriez; 10-11-2016 at 07:06 AM.. |
Appreciate
0
|
10-04-2016, 05:02 PM | #104 | |
Ballin' out of control.
523
Rep 1,289
Posts |
Quote:
The INPA.INI configuration file in the C:\EC-APPS\INPA\CFGDAT folder sets the function key assignments for chassis selection. The chassis specific script selections can be found in the *.ENG configuration files, which are also located in the CFGDAT folder...i.e. E90.ENG.
__________________
Alpina B3 Flash/BMS OCC/ER CP/ETS 5/HKS BOV/M3 Control Arms
|
|
Appreciate
1
milfriez29.50 |
10-05-2016, 11:59 AM | #105 | |
Private First Class
30
Rep 106
Posts |
Quote:
Once I went back and replaced it with the updated .INI and then recopied the CFGDAT and SGDAT files over, everything seems to check out, along with an expanded vehicle menu select. Thanks for that! P.S. If anyone is still has a Windows 7 box sitting around, using Win7+XP Mode (MS virtual PC) is the way to go instead of installing, killing install, reinstalling, etc. Just build the VM, follow the install, extract your files, then copy to Win7/Win10 system. After you're done just kill off the VM all neat and clean. |
|
Appreciate
0
|
10-10-2016, 02:57 PM | #106 |
Private First Class
30
Rep 106
Posts |
Okay back again.
Got everything installed and up and running. In INPA I can select E89 and the appropriate engine. Past that point, all is in German and German metrics. I know that I had copied the eng files across but for some reason, it appears as if it is not reading them. How can I get them to display english units/titles instead of German? Thanks, Brad |
Appreciate
0
|
10-11-2016, 06:23 PM | #107 | |||
Ballin' out of control.
523
Rep 1,289
Posts |
Quote:
Quote:
Quote:
The *.ENG configuration files only specify which chassis specific INPA scripts are to be executed. They do not influence the language variant and/or system of measure utilized by those scripts. This DIY explains how to obtain and install English metric INPA scripts. If that's what your seeking, I suggest following the DIY...
__________________
Alpina B3 Flash/BMS OCC/ER CP/ETS 5/HKS BOV/M3 Control Arms
|
|||
Appreciate
0
|
10-27-2016, 06:15 AM | #108 |
Private
13
Rep 86
Posts |
|
Appreciate
0
|
10-27-2016, 10:08 PM | #109 |
Private
13
Rep 86
Posts |
Microsoft Register Server32
This is what happens when I attempt the step to load the NFS\Entpackt.
Instructions say ActiveX controls will fail to register. I don't see that happening |
Appreciate
0
|
Bookmarks |
Tags |
bmw standard tools, coding, diy, inpa, winkfp |
|
|