[outie]

Originally Posted by woodpecka

Just adding the option to the VO should activate the function?

Thanks for the info.

Try, I cannot confirm that it will work but that's a good starting point.

Originally Posted by Pseudo Nim

Is it $459 or $458A / $459A?

S458A ELECTR.FRONT SEAT ADJUSTMENT
S459A EL.FRONT SEAT ADJUSTMENT W. MEMORY

based on post #503. Or you don't need the A at the end?

No "A". It should be $459.

[Pseudo Nim]

Originally Posted by outie

Try, I cannot confirm that it will work but that's a good starting point.


No "A". It should be $459.

Understood.

Curious - any difference between 458 and 459? Both seem to be seat memory.

[woodpecka]

Originally Posted by Pseudo Nim

Understood.

Curious - any difference between 458 and 459? Both seem to be seat memory.

458 seem without memory, 459 with memory. no?

So adding the option into the VO will set the module values accordingly ?

[Pseudo Nim]

Originally Posted by woodpecka

458 seem without memory, 459 with memory. no?

So adding the option into the VO will set the module values accordingly ?

oops my bad, hahaha

[outie]

Originally Posted by woodpecka

458 seem without memory, 459 with memory. no?

So adding the option into the VO will set the module values accordingly ?

Add VO and FA_write to CAS + FRM. Backup & Recode.

[spazticrecords]

I know this really isn't the place but I am having a problem coding any other cars. I can code E90 no issue but no other cars. I've tried E46, and E65/E66 and I get the same error on both cars, that no response from ECU. Am I doing something wrong?

[BeWide]

Originally Posted by spazticrecords

I know this really isn't the place but I am having a problem coding any other cars. I can code E90 no issue but no other cars. I've tried E46, and E65/E66 and I get the same error on both cars, that no response from ECU. Am I doing something wrong?

To work with these old model you should solder the pin 8 of your cable

Here is the vendor advise :

"This picture below is useful for people with the latest BMW models which got Ethernet available on the OBD2 plug, BMW uses pin8 to enable this Ethernet connection, unfortunately this pin is (was) also used as 2nd K-Line for a couple of older BMW models, we do connect the K-Line to pin8 as well to be fully backward compatible to those older models, if you have such a new model with Ethernet and experience "communication disturbed" as soon as the diagnostic begins we advice you to remove pin8 by soldering it out.
( Interfaces shipped from now on will have pin8 removed already, in case you need the backward compatibility for older K-Line equipped cars that have some modules connected to pin8 we offer an adapter for that - just contact us and ask for details )"

[tldoxmf87]

Originally Posted by outie

Try this one too (I think it's this one actually):
CC_MEL_SL_BEI_DEF_RL_BL_1

I coded everything but still shows the 'daytime running light / parking lamp malfunction'.
Hmmm..
Maybe I have to clear the error first?

[tldoxmf87]

DRL_V_GEDIMMT
aktiv

DRL_WERT_DIMMUNG
wert_01

I found two codes in FRM relating to the DRL dimming.
Maybe if we change this setting somehow it won't dim the angel eyes when headlamp is on?? I haven't tried but just throwing it out there for someone to try.

[xxxjecxxx]

Originally Posted by JETBLK335i

Hi all, I'm doing this from a blackberry, but can someone please help me with the code to remove this error?

i got rid of this error in my car after euro conversion from halogen

FRM module
LICHT_AN_WARNUNG
aktiv> nicht_aktiv

If i'm not mistaken this gets rid of any light warnings. If a bulb goes out, the computer will still tell you.

[Toshi]

Originally Posted by tldoxmf87

I coded everything but still shows the 'daytime running light / parking lamp malfunction'.
Hmmm..
Maybe I have to clear the error first?

Try "CC_MELD_PARKLICHT".

[BeWide]

Originally Posted by xxxjecxxx

i got rid of this error in my car after euro conversion from halogen

FRM module
LICHT_AN_WARNUNG
aktiv> nicht_aktiv

If i'm not mistaken this gets rid of any light warnings. If a bulb goes out, the computer will still tell you.

Please check your private message...


EDIT : Tested my cable on a Mini R50, same problem... Have restarted all the procedure. Deleted all file , redownloaded... NOTHING !

Have contacted the seller, NO REPLY .... F**K

[brinx38]

Originally Posted by brinx38

anyone knows what error code CDA9 stands for?

It comes back every time i clear error memory. I've still


I think this is what's triggering that "service engine soon" light..

anyone?

[el-drifot]

Added entry about Wiper end Position in the Spreadsheet... Check it out!

Greetz
El-Drifto

[cedchung]

requested access.. thanks

[tldoxmf87]

Originally Posted by Toshi

Try "CC_MELD_PARKLICHT".

It worked!!
I actully had to deactivate the WARM and COLD check and the FEHLERMELDUNG for the front turn signals.
I think it's because I have the euro headlights which doesn't turn on the turn signals when headlights are on.

[Pseudo Nim]

hot damn. tried to code paddles in egs from wert_00 to wert_01 - DS mode disappeared

[woodpecka]

Originally Posted by Pseudo Nim

hot damn. tried to code paddles in egs from wert_00 to wert_01 - DS mode disappeared

you are using the Satan's cable!

[spazticrecords]

Originally Posted by el-drifot

Added entry about Wiper end Position in the Spreadsheet... Check it out!

Greetz
El-Drifto

Nice find. How did you find this one? I tested and works great.

[cedchung]

This is my first time trying this. The video says to work with the FSW_PSW.MAN file while the DIY PDF says FSW_PSW.TRC. Which one is it?

[Toshi]

Originally Posted by Toshi

Try "CC_MELD_PARKLICHT".

Originally Posted by tldoxmf87

It worked!!
I actully had to deactivate the WARM and COLD check and the FEHLERMELDUNG for the front turn signals.
I think it's because I have the euro headlights which doesn't turn on the turn signals when headlights are on.

[outie]

Originally Posted by cedchung

This is my first time trying this. The video says to work with the FSW_PSW.MAN file while the DIY PDF says FSW_PSW.TRC. Which one is it?

You are confused. Follow the PDF. When you read the module the file generated is "FSW_PSW.TRC". You need to rename it to "FSW_PSW.MAN" in order for NCS to code the new parameters. The .man file is what NCS uses to code the car.