[SilverStreak18]

Originally Posted by Raptor001

Resolved; issue was I coding with expert mode profile and I needed to use a CNCoding profile; working now.

It seems I'm having the same issue. Install went perfectly, I'm able to connect to the car in both INPA and NCSExpert, but when I change things they don't take. It says coding, then coding successful, car makes the audible ding sound that something happened but nothing actually changes. I will try to use CNCoding Profile tomorrow night and see if thats my solution. I don't understand why it would work though when the instructions say to use Expert Profile.

[SilverStreak18]

Round two. Everything worked perfectly and I successfully coded my car! My thanks goes out to wildcatcrazy for this thread. My new favorite thing about my car; it doesn't ding at all when the dam door is open!

[wildcatcrazy]

Originally Posted by xyzed

After I did a clean install of Windows 10 and installed the software NCS is in German. Anyone know what I need to do to get it to show English?

Also, make sure during the install that you delete the entire NCSEXPER, EC-APPS and EDIABAS folders before you copy my folders onto your C drive. Instead of copying/overwriting the folders that were initially created during the install.

[tdavis42]

wildcatcrazy I am having issues registering a new battery with Tool32.

I open Tool32 and try to load a profile and nothing ever opens I just get the spinning windows circle forever. I have tried loading 08MSV70.PRG.

I am assuming this is the correct one as I have a 2008 328i E90.

Thanks for all your help and contributions to this community!

[rocksarntpeople]

seems like the Mega link is down for the daten files...looking for e89 latest if anyone has a working link. Thanks.

[wildcatcrazy]

Originally Posted by tdavis42

wildcatcrazy I am having issues registering a new battery with Tool32.

I open Tool32 and try to load a profile and nothing ever opens I just get the spinning windows circle forever. I have tried loading 08MSV70.PRG.

I am assuming this is the correct one as I have a 2008 328i E90.

Thanks for all your help and contributions to this community!

Right click and run Tool32 as admin.

Originally Posted by rocksarntpeople

seems like the Mega link is down for the daten files...looking for e89 latest if anyone has a working link. Thanks.

New DATEN link uploaded (v60.0).

[TheM3Boy]

I have been trying to download the tools from mediafire but the downloaded zip file is always corrupted. If I download a single file it is fine. I have tried different browsers and OSes. Is anyone else experiencing a similar issue?

[AviatorBimmerFL]

Originally Posted by TheM3Boy

I have been trying to download the tools from mediafire but the downloaded zip file is always corrupted. If I download a single file it is fine. I have tried different browsers and OSes. Is anyone else experiencing a similar issue?

You must use the 7Zip software to unzip it.

[GottWhat]

Originally Posted by AviatorBimmerFL

You must use the 7Zip software to unzip it.

Also, make sure you are using the most current version. I was having issues until I updated mine...

[TheM3Boy]

Originally Posted by GottWhat

Also, make sure you are using the most current version. I was having issues until I updated mine...

I am using 7zip for all my archives but because it is normally the first tool I install on a machine they were pretty outdated. Updated to the latest and now it appears to unzip them although I still get an error "Unexpected end of data"

Thanks guys!

[red9r]

Anyone know where I can get the E90 and E92 Daten files?

[tryingtobebest]

Hey Wildcat, you helped me sometime ago but now i have very strange issue! I know how coding works and i know steps, i did coding myself on this computer through this very cable on my own car summertime but now the issue is NCS Expert is not able to write edited .Man file!!!
For example if i read Airbag and want to disable faher (driver seatbelt) warning i read with NCS then edit TRC with dummy then save .man file then change job in NCS to SG_Co..., process, then go through ignition cycle, then _Lessen with NCS again and values are still unchanged!(((

Also:
I did used 2.0 and 3.0 port on my laptop with no success
I did try it with car running, ignition ON (not running), charging with 40AMP, 20AMP and 2Amp settings on charger with NO SUCCESS
I deleted TRC file and leave .man file and process with WRITE (CG_CODIEREN) with NCS it didn't do anything
it just looks like NCS is writing original VO setting to the module im working with...


If YOU or anyone else know/read/face this or similar problem PLEASE let me know where to read more about it or what you did to solve this!

THX
TTBB

EDIT: Car is 2009 (LCI) E90 335D

[ACCENG]

I am getting the following error when trying to access my transmission everything else seems to work perfectly. Any help would be really appreciated.

[Joe@TopGearSolutions]

Enter 5 or 6, depending on which one you have.

[ACCENG]

Originally Posted by Joe@TopGearSolutions

Enter 5 or 6, depending on which one you have.

Thank you for your help, that does work but all the menus are still in German. I ended up wiping my computer and reinstalling everything following this diy http://www.e90post.com/forums/showthread.php?t=918608. All works great now.

[Joe@TopGearSolutions]

Originally Posted by tryingtobebest

Hey Wildcat, you helped me sometime ago but now i have very strange issue! I know how coding works and i know steps, i did coding myself on this computer through this very cable on my own car summertime but now the issue is NCS Expert is not able to write edited .Man file!!!
For example if i read Airbag and want to disable faher (driver seatbelt) warning i read with NCS then edit TRC with dummy then save .man file then change job in NCS to SG_Co..., process, then go through ignition cycle, then _Lessen with NCS again and values are still unchanged!(((

Also:
I did used 2.0 and 3.0 port on my laptop with no success
I did try it with car running, ignition ON (not running), charging with 40AMP, 20AMP and 2Amp settings on charger with NO SUCCESS
I deleted TRC file and leave .man file and process with WRITE (CG_CODIEREN) with NCS it didn't do anything
it just looks like NCS is writing original VO setting to the module im working with...


If YOU or anyone else know/read/face this or similar problem PLEASE let me know where to read more about it or what you did to solve this!

THX
TTBB

EDIT: Car is 2009 (LCI) E90 335D

Make sure you are using the CNCoding profile, not ExpertMode.

[xyzed]

Why would INPA show battery & ignition ON when I am not plugged into the cars OBD port?

[Joe@TopGearSolutions]

Typically a sign of a bad cable.

[xyzed]

Originally Posted by Joe@TopGearSolutions

Typically a sign of a bad cable.

so what rhymes with simmer ??

Dimmer Limmer Glimmer????

[Joe@TopGearSolutions]

Originally Posted by xyzed

so what rhymes with simmer ??

Dimmer Limmer Glimmer????

Where did you get the cable?

[xyzed]

Originally Posted by Joe@TopGearSolutions

Where did you get the cable?

OBDInnovations.???

Bought without the Software package. I think its a fake FTDI. It worked well and then windows updated and now it wont work??

[Joe@TopGearSolutions]

Originally Posted by xyzed

OBDInnovations.???

Bought without the Software package. I think its a fake FTDI. It worked well and then windows updated and now it wont work??

PM sent.