|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
CCC drive swap Question
|
|
03-17-2019, 12:13 AM | #1 |
Second Lieutenant
57
Rep 264
Posts |
CCC drive swap Question
Ok so long story short my CCC drive just took a toll on me. The knob spins freely, I get no audio at all, and the best part is that the idrive does not even turn on anymore. I had to disconnect the amp because it was draining my battery :/ .
SO my question is, I'm in the works of shopping for a used CCC drive and wanted to know if I can swap from an 07 335i e92 CCC(the broken) to a used 2008 335i e90 CCC(Used). I know coding will be involved. But I wanted to know if it was possible. Both CCC drive has different faceplates but the back looks identical(connectors etc) Thanks!!! |
03-17-2019, 12:25 AM | #2 |
Lieutenant General
1904
Rep 13,088
Posts |
perhaps you should see the idrive and coding sub forums.
I would compare part no's to make sure they are both ccc. Coding might be easier than you think . If you are lucky you can default code from the VO or if your real lucky the donor car has identical options. |
Appreciate
0
|
03-17-2019, 01:10 AM | #3 |
Second Lieutenant
57
Rep 264
Posts |
the coding would be the easy part, but im having 2nd thoughts on the fitment. they are both CCC .
|
Appreciate
0
|
03-17-2019, 05:05 PM | #4 | |
Lieutenant Colonel
1456
Rep 1,909
Posts |
Quote:
Keep in mind if you are paying more than $150 for a CCC you are paying way too much. https://www.ebay.com/itm/Audio-Equip...d=123606768769 |
|
Appreciate
0
|
03-17-2019, 06:10 PM | #5 | |
Second Lieutenant
57
Rep 264
Posts |
Quote:
|
|
Appreciate
0
|
03-20-2019, 08:35 AM | #6 | |
Second Lieutenant
57
Rep 264
Posts |
Quote:
|
|
Appreciate
0
|
03-20-2019, 10:07 AM | #7 |
Lieutenant Colonel
1456
Rep 1,909
Posts |
|
Appreciate
0
|
03-20-2019, 10:12 AM | #8 |
Master of Montego Blue
27
Rep 500
Posts |
|
Appreciate
0
|
03-20-2019, 12:37 PM | #9 |
Lieutenant Colonel
1456
Rep 1,909
Posts |
|
Appreciate
0
|
03-20-2019, 02:41 PM | #10 |
Master of Montego Blue
27
Rep 500
Posts |
|
Appreciate
0
|
03-21-2019, 03:42 AM | #11 |
Second Lieutenant
57
Rep 264
Posts |
|
Appreciate
0
|
07-26-2019, 12:27 PM | #13 |
New Member
0
Rep 25
Posts |
Hi all, I just wanted to ask jyjimenez3 what kind of problems did you run into installing the unit other then just needing a new face plate also if its not too much to ask can you do a step by step on the coding part? much appreciated.
|
Appreciate
0
|
03-17-2020, 07:12 PM | #14 |
First Lieutenant
247
Rep 388
Posts
Drives: 2006 M5, 2012 X5d, 2008 E91
Join Date: Aug 2012
Location: Seattle
|
I just did this swap and am having some troubles with the button operation. I replaced a CCC unit from an 07 (no pre-set buttons) with a newer unit which has the 6 preset buttons. When I first installed the new unit the buttons seemed to function, but there was no sound. I then coded the new unit using NCSExpert (modules CAPPL, CAUDI, CGATE, CHOST, CTUNE) as described in many places on various forums, and the sound works! The preset buttons no longer work though. Is there another module which requires coding for these buttons to function?
|
Appreciate
0
|
03-21-2020, 12:01 AM | #15 | |
Lieutenant Colonel
1456
Rep 1,909
Posts |
Quote:
|
|
Appreciate
0
|
03-23-2020, 08:50 PM | #16 |
First Lieutenant
247
Rep 388
Posts
Drives: 2006 M5, 2012 X5d, 2008 E91
Join Date: Aug 2012
Location: Seattle
|
|
Appreciate
0
|
04-04-2020, 11:21 PM | #17 |
New Member
0
Rep 6
Posts |
Hey jbash,
Mind sending a pic of your coding setup? I have the same issue where I just swapped an old CCC to a newer version CCC and no sound (also no bluetooth? and no voice commands?) but I need to code it, apparently. I bought this iCar Pro which is pretty cool, but I need a good app that would work with it. BimmerCode doesn't work for pre-2008 E90's. |
Appreciate
0
|
04-05-2020, 10:29 AM | #18 |
Lieutenant General
1904
Rep 13,088
Posts |
there is a 3/07 cut off date for K/D can cable programing of
Most Bus Modules. You need and Icom after that. Maybe Nicko found away around that. Last edited by ctuna; 04-05-2020 at 10:37 AM.. |
Appreciate
0
|
06-28-2020, 01:58 PM | #19 |
New Member
0
Rep 9
Posts |
Hi,
I am in same trouble, i replaced my dead CCC for newer with preset buttons and they worked till coding. I see that changing build date solves problem but need help because I don't know how to change build date. Would somebody be kind to help? THX |
Appreciate
0
|
01-06-2023, 07:14 PM | #20 | |
Registered
0
Rep 1
Posts |
Quote:
In NCS Expert youll want to do the standard VIN/ZCS/FA (F1), ZCS/FA f. ECU (F3) (read from CAS), then Enter FA (F2), choose E89, click ok when vin pops up, then the top value (mine is #0305) needs to be deleted, then in the attribute window enter #0307 and click add. This will update your FA and you should see #0307 at the top of the list, click ok. you should then see on the main menu Chassis: E90 (E89), FG *insert your vin here*, and FA E90_#0307 followed by the rest of the crap. Then go back and code the CAPPL, CAUDI, CGATE, CHOST, and CTUNE with that FA. If i get a chance ill try to upload some pictures because i know all text sucks. Also a thanks to everyone here. Very to have the 2nd Gen CCC in the car. I havent had a radio in months. I missed my Logic 7 badly |
|
Appreciate
0
|
03-25-2023, 04:10 PM | #21 |
Registered
0
Rep 2
Posts |
Sorry to revive an old thread but ive just chaged my motherboard from a 05 pre lci e60 to a lci ccc with preset buttons from an e91 but its not working unless i put the e91 faceplate on.
Does anyone know if you can code it to work on the e60 non preset faceplate please. |
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|