E90Post
 


 
BMW 3-Series (E90 E92) Forum > BMW E90/E92/E93 3-series General Forums > Photo/Video/Media Gallery > E91 Leonia



Reply
 
Thread Tools Search this Thread
      04-24-2021, 02:38 PM   #67
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

I've been doing as much clean up of the engine bay as I can while I go. It will make working on the car much easier/cleaner in the future. It's an old car... so I'm going to assume i'll need to tinker with it at least once a summer season.

This is how the side of the engine looked the first time I removed the intake manifold.


Having some more experience w/ the car now, I think most of the oil/grease buildup is due to the bad oil filter housing gasket. I tried to use degreaser to clean the gunk but I couldn't get it all off.

I tried again last week with more degreaser + hot water, followed by a good strong pressure wash. I think it did the trick!

__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 1
donut_boi815.00
      04-25-2021, 12:56 PM   #68
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

I previously noticed the power steering reservoir cap was gunky and I think it was leaking.
I went ahead and replaced the 3 dollar gasket. Lets see if that fixes the problem.



__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 1
donut_boi815.00
      04-29-2021, 01:10 PM   #69
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

Since I want to cover most of the bulk issues of a 10-year old car engine and transmission wise, I went ahead and pulled out the vanos solenoids and replaced them with new, oem ones.

Old ones.



New ones


Visual Comparison between new and old
__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 0
      04-29-2021, 01:33 PM   #70
michaelalex17
Brigadier General
michaelalex17's Avatar
403
Rep
3,076
Posts

Drives: Manual Wagon
Join Date: Aug 2010
Location: CT

iTrader: (4)

Quote:
Originally Posted by bshambam View Post
Since I want to cover most of the bulk issues of a 10-year old car engine and transmission wise, I went ahead and pulled out the vanos solenoids and replaced them with new, oem ones.

Old ones.



New ones


Visual Comparison between new and old
Notice any difference with the new Vanos solenoids?
__________________
Appreciate 0
      04-29-2021, 06:44 PM   #71
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

Quote:
Originally Posted by michaelalex17 View Post
Notice any difference with the new Vanos solenoids?
I'll be sure to report back when I get the car on the road.
__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 0
      05-04-2021, 12:24 AM   #72
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

Finally had time to sit in front of the computer.... as if we needed more of that? ha!

Here is the first concept of the Front Seal Tool.



Just starting off and it can get a bit complicated. I'll refine and clean it up as I go along.
__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 1
      05-04-2021, 05:42 PM   #73
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

Here is an update. I think I'm satisfied enough with it to print it out. It will be 2 pieces compared to the 3 pieces that are sold on the market.



The pieces I'll need to pull the existing seal out


And the piece with the alignment tool provided to put it back in.
__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 2
      05-07-2021, 11:34 PM   #74
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

I had some down time during work today so I managed to make both prints for the weekend! Super excited to try things out.


__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 0
      05-14-2021, 03:18 PM   #75
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

I had to do some slight modification to the piece in order to fit some of the bolt heads



Here is the piece bolted into place, with the first test screw to extract the crank seal



And all the extractor screws are aligned & in-place

__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 0
      05-25-2021, 11:43 AM   #76
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

well now....
This whole front seal installation DIY process took a turn for the worse..

__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 0
      05-25-2021, 11:45 AM   #77
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

Butttttt

There's always a positive light @ the end of the tunnel... or... when you screwed the duck and fix it with bling

__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 2
      05-27-2021, 11:13 AM   #78
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

This is a disclaimer for anyone who may be interested in the ATI Harmonic Damper for the n52.

The oem Crank Hub bolts will not work. The flange is too big for the machining & boss size at the damper (the flange size of the oem bolt is 15mm, whereas the damper only has approx. 14mm circumference). You will need to buy your own bolts. Calvin from VAC has not replied to my bolt inquiry and ATI does not list any bolts on their website.
__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 0
      05-27-2021, 11:30 AM   #79
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

Successfully re-installed the Front Crank Seal with the required Loctite sealant.

Installed the seal guard that i picked up on ebay. It cost 130 bucks.


__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 0
      05-28-2021, 12:28 PM   #80
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

Update: Calvin from VAC gave me a call and it was a mistake. The crank hub does in fact come with bolts....

However... I went ahead and purchased stainless steel hardened socket bolts from mcmaster carr.... for a good 80 dollars haha ouch.
__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 0
      06-01-2021, 11:54 PM   #81
tetsuo111
Save the Manuals!
tetsuo111's Avatar
United_States
983
Rep
1,189
Posts

Drives: 2011 RWD 6MT ZSP Sportwagon
Join Date: Dec 2014
Location: PNW

iTrader: (0)

Garage List
Quote:
Originally Posted by bshambam View Post
Since I want to cover most of the bulk issues of a 10-year old car engine and transmission wise, I went ahead and pulled out the vanos solenoids and replaced them with new, oem ones.
Curious - what should we look for when visually inspecting the solenoids?

Thanks for documenting your experience!
__________________
2011 E91 6MT RWD ClubSport Wagon | 3,185lbs | 1 of 429 delivered in North America
Outside: BMW Aero, Euro lighting, Philips Ultinon, Seibon | Inside: Recaro, Prototipo, AutoSolutions SSK, UCP, Safecraft | Control: StageFP, M3 Kombi | Stop: M3 hydraulics, M3 ST-40R, PFC | Grip: M3 Chassis+Rear Coilover conversion, M3 Nitron R3, Hyperco, ARC-8 255, Billet RSBs | Go: Snorkel, Euro PI, 3IM, MILVs, SS Headers+Ceramic, Dundon 321/Inconel exhaust, VPhreaks | Cool: CSF | PCA #2018100384 | BMW CCA #505794
Appreciate 0
      06-16-2021, 03:00 PM   #82
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

Quote:
Originally Posted by tetsuo111 View Post
Curious - what should we look for when visually inspecting the solenoids?

Thanks for documenting your experience!
You tend not to see hard debris anywhere near these solenoids. As per youtube, the only true way to test functionality is to set them up on a rig with power and let them cycle through clean oil.

That process would also help purge impure particulates.

I don't think visuals really help in this situation due to the nature of the electronic component.
__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 0
      06-16-2021, 03:08 PM   #83
Skoidat69
Secret Squirrel
Skoidat69's Avatar
United_States
162
Rep
247
Posts

Drives: 2007 BMW 328ix E91
Join Date: Oct 2019
Location: StL

iTrader: (0)

Garage List
2007 BMW 328XI  [0.00]
Quote:
Originally Posted by bshambam View Post
This is a disclaimer for anyone who may be interested in the ATI Harmonic Damper for the n52.

The oem Crank Hub bolts will not work. The flange is too big for the machining & boss size at the damper (the flange size of the oem bolt is 15mm, whereas the damper only has approx. 14mm circumference). You will need to buy your own bolts. Calvin from VAC has not replied to my bolt inquiry and ATI does not list any bolts on their website.
Quote:
Originally Posted by bshambam View Post
This is a disclaimer for anyone who may be interested in the ATI Harmonic Damper for the n52.

The oem Crank Hub bolts will not work. The flange is too big for the machining & boss size at the damper (the flange size of the oem bolt is 15mm, whereas the damper only has approx. 14mm circumference). You will need to buy your own bolts. Calvin from VAC has not replied to my bolt inquiry and ATI does not list any bolts on their website.
What is the advantage of the ATI Harmonic Damper?
__________________
No good sea story starts with Cookies and Milk
Appreciate 0
      06-17-2021, 07:31 PM   #84
bshambam
Private First Class
bshambam's Avatar
77
Rep
122
Posts

Drives: bmw e91
Join Date: Jul 2020
Location: canada

iTrader: (0)

Quote:
Originally Posted by Skoidat69 View Post
What is the advantage of the ATI Harmonic Damper?
The ATI Damper uses fluid to take out unwanted frequencies that the oem balancer is not prepared for, nor the original rubber component of the pulley. The pulley is 12 years old now, and i'm sure the german rubber is all dried up.

There are zero performance advantages to the engine in it's OEM configuration.

However, If were to push it to it's max ie: hit the rev limiter all the time, and aggressively pushing it on the track, that is when you would see the maximum advantage. The reason why I purchased it was to extend the longevity of the engine and the long IL-6 crankshaft.

The chain linked balancer inside the engine, attached to the crankshaft is supposed to take out a lot of the frequency within the engine, but this does not include the flywheel nor the pulley.

There is internal engine balance, with your pistons, rods, crankshafts all balanced from cylinders 1-6, and there is external balance inclusive of the components mentioned on the internal balance + flywheel & pulley weight.

to my knowledge, most manufacturers don't do external balance unless they are building race cars, and my 12 year old e91 is not lol

I've put fluid balancer's on all my cars. It is an rather expensive piece at 1100 dollars, but you are paying that high price for a reason.
__________________
William Mackenzie

IG: Shambam_makes
Twitter: B_Shambam
Appreciate 1
Skoidat69162.00
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 06:46 AM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST