2013 E92 328i M-Sport 6 Speed Build Thread

dudemanppl · 12-05-2023, 09:24 PM

Origin Story

N52s (or N51 in this case

) have always been neat to me and my friend was getting rid of this thing for cheap after I called first dibs on it so here we are!

Crazy build spec; 2013, single owner (effectively), slicktop, single hump, manual seats, M-Sport, and 6 speed. Ideally, it wouldn't be black nor have wood trim, but the latter is an easy and relatively inexpensive fix.

I'll get photos some other time, its completely stock and Black Sapphire Metallic, extremely un-noteworthy.

Build Plans

Trying to turn it in to a car where I don't have to worry about anything mechanically, look sick, and be fun in corners.

So far I have ordered:

Maintenance

Water Pump/Thermostat Kit w/ aluminum Mickey Mouse hose
All coolant O-rings
Oil Pan Gasket w/ new bolts
All the valve cover gaskets + OFHG
Engine Oil, Trans/Diff fluids
Cabin/Engine Air filters
OEM Motor/Trans Mounts
Ignition Coil/Spark Plugs
LUK DMFW/Clutch kit
Tie Rods/boots
OEM Clutch Pivot Pin
OEM Differential Bushings
Selector rod joint bushing

Suspension/Performance

Kinematic Speed Shifter
RedShift Motorsports Street Coilovers 5/7k
PMC Camber/Caster Plates
IRP Spherical Lower Shock Mount
AKG Upper 85A Upper Shock Mount
IRP Poly Subframe Bushings
Meyle Trailing Arm Ball Joints 3147100005
Camber arm knuckle Ball Joint
IRP Camber Arm Inner Spherical Bearing
PMC Full Rear Adjustable Arm Kit (Toe, Guide, Upper) w/ Spherical rod ends
M3 Front Tension Arms w/ IRP Spherical Bearing
Non-M Front Control Arms w/ AKG Spherical Bearing

Wheels

Apex VS5RS 18x9.5 ET22 square in Motorsport Gold
Michelin Pilot Sport 4S 245/35/R18

Note: Apex recommended against this fitment, planning to run -3.7F/-2.5R for camber, zero toe F/R. It'll also likely require a rear fender pull, roll, and/or shave. I'm also running smaller diameter and narrower tires than usual. Backordered until ~April 2024 so I guess I'll find out then!

Future Plans

In the immediate future, mechanically, it needs new front wheel bearings and a new transmission as the third gear synchro is gone.

Cosmetics

The car is definitely a 10 footer as it sits, but honestly it would be just a paint correction, maybe a front and rear bumper respray along with a lip, spoiler, and maybe side skirt extensions. The rear parcel shelf is sun faded, so I'll respray that. Headliner and pillars are good!

Powertrain

Not sure on plans for the exhaust just yet, the Condor SE9x headers seem to put out good power.

I'm also pretty interested in the yet-to-be-released 22RPD trumpet setup along with some MILVs if those ever come back in to existence.

The 163k mile motor also has a decent lifter tick so I may tackle that down the line as well... or get an N52 to put in (and also do the lifters on that preventatively).

No current codes for VANOS, DISA, or Valvetronic motor but I wouldn't be surprised if those become an issue.

Driveline

Will probably pick up a 3.73 diff to rebuild with a plated LSD along with a REM polish of the ring gear and pinion.

No current CSB or guibo issues, will check the condition whenever I get under this thing.

Brakes

No plans yet other than new fluid.

Feel free to chime in with any other common N51/2 issues I won't be addressing as I'm new to the E9x platform!

whyzee125 · 12-05-2023, 10:21 PM

Welcome! Love to see pics of your new beast, sounds like a super fun project and I"m drooling over your mod/maintenance list already. Should be a blast!

dudemanppl · 01-26-2024, 09:22 PM

Motor has a hole in the block now before even starting wrenching on it, oops! Selling the car after putting a new motor in if anyone is interested.

whyzee125 · 02-01-2024, 07:45 AM

That sucks! You already ordered so many parts for it too.

12-05-2023, 09:24 PM	#1
dudemanppl New Member 2 Rep 6 Posts Drives: 2011 E92 M3 Join Date: Nov 2023 Location: LA iTrader: (0)	2013 E92 328i M-Sport 6 Speed Build Thread Origin Story N52s (or N51 in this case ) have always been neat to me and my friend was getting rid of this thing for cheap after I called first dibs on it so here we are! Crazy build spec; 2013, single owner (effectively), slicktop, single hump, manual seats, M-Sport, and 6 speed. Ideally, it wouldn't be black nor have wood trim, but the latter is an easy and relatively inexpensive fix. I'll get photos some other time, its completely stock and Black Sapphire Metallic, extremely un-noteworthy. Build Plans Trying to turn it in to a car where I don't have to worry about anything mechanically, look sick, and be fun in corners. So far I have ordered: Maintenance Water Pump/Thermostat Kit w/ aluminum Mickey Mouse hose All coolant O-rings Oil Pan Gasket w/ new bolts All the valve cover gaskets + OFHG Engine Oil, Trans/Diff fluids Cabin/Engine Air filters OEM Motor/Trans Mounts Ignition Coil/Spark Plugs LUK DMFW/Clutch kit Tie Rods/boots OEM Clutch Pivot Pin OEM Differential Bushings Selector rod joint bushing Suspension/Performance Kinematic Speed Shifter RedShift Motorsports Street Coilovers 5/7k PMC Camber/Caster Plates IRP Spherical Lower Shock Mount AKG Upper 85A Upper Shock Mount IRP Poly Subframe Bushings Meyle Trailing Arm Ball Joints 3147100005 Camber arm knuckle Ball Joint IRP Camber Arm Inner Spherical Bearing PMC Full Rear Adjustable Arm Kit (Toe, Guide, Upper) w/ Spherical rod ends M3 Front Tension Arms w/ IRP Spherical Bearing Non-M Front Control Arms w/ AKG Spherical Bearing Wheels Apex VS5RS 18x9.5 ET22 square in Motorsport Gold Michelin Pilot Sport 4S 245/35/R18 Note: Apex recommended against this fitment, planning to run -3.7F/-2.5R for camber, zero toe F/R. It'll also likely require a rear fender pull, roll, and/or shave. I'm also running smaller diameter and narrower tires than usual. Backordered until ~April 2024 so I guess I'll find out then! Future Plans In the immediate future, mechanically, it needs new front wheel bearings and a new transmission as the third gear synchro is gone. Cosmetics The car is definitely a 10 footer as it sits, but honestly it would be just a paint correction, maybe a front and rear bumper respray along with a lip, spoiler, and maybe side skirt extensions. The rear parcel shelf is sun faded, so I'll respray that. Headliner and pillars are good! Powertrain Not sure on plans for the exhaust just yet, the Condor SE9x headers seem to put out good power. I'm also pretty interested in the yet-to-be-released 22RPD trumpet setup along with some MILVs if those ever come back in to existence. The 163k mile motor also has a decent lifter tick so I may tackle that down the line as well... or get an N52 to put in (and also do the lifters on that preventatively). No current codes for VANOS, DISA, or Valvetronic motor but I wouldn't be surprised if those become an issue. Driveline Will probably pick up a 3.73 diff to rebuild with a plated LSD along with a REM polish of the ring gear and pinion. No current CSB or guibo issues, will check the condition whenever I get under this thing. Brakes No plans yet other than new fluid. Feel free to chime in with any other common N51/2 issues I won't be addressing as I'm new to the E9x platform! Last edited by dudemanppl; 12-05-2023 at 11:17 PM..
	Appreciate 1 whyzee1251678.50 Tweet Quote

12-05-2023, 10:21 PM	#2
whyzee125 Brigadier General 1679 Rep 3,645 Posts Drives: Dinan stage 2 335i Join Date: Jul 2014 Location: Chattanooga Tn iTrader: (0)	Welcome! Love to see pics of your new beast, sounds like a super fun project and I"m drooling over your mod/maintenance list already. Should be a blast!
	Appreciate 0 Quote

01-26-2024, 09:22 PM	#3
dudemanppl New Member 2 Rep 6 Posts Drives: 2011 E92 M3 Join Date: Nov 2023 Location: LA iTrader: (0)	Motor has a hole in the block now before even starting wrenching on it, oops! Selling the car after putting a new motor in if anyone is interested.
	Appreciate 0 Quote

02-01-2024, 07:45 AM	#4
whyzee125 Brigadier General 1679 Rep 3,645 Posts Drives: Dinan stage 2 335i Join Date: Jul 2014 Location: Chattanooga Tn iTrader: (0)	That sucks! You already ordered so many parts for it too.
	Appreciate 0 Quote