E90Post
 


The Tire Rack
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Powertrain and Drivetrain Discussions > N54 Turbo Engine / Drivetrain / Exhaust Modifications - 335i > How To: Aftermarket Wideband AFR sensor into Procede



Reply
 
Thread Tools Search this Thread
      09-20-2012, 11:55 AM   #1
OpenFlash
United_States
1275
Rep
17,863
Posts

Drives: A Lot
Join Date: Sep 2006
Location: SF Bay, CA

iTrader: (0)

Garage List
Exclamation How To: Aftermarket Wideband AFR sensor into Procede

Hi guys
It's a pretty simple job. Shouldn't take more than a few minutes. What you need to find is the output wire on your aftermarket wideband sensor (Innovate, Autronic, FJO, etc,.) that proves a "linear 0-5v" output signal.

If you have a Rev 2 harness:
You will feed this wire into the input wire of the o2 modifier wire bundle (that hasn't been used in ages and has been taped up and secured to the rest of the harness). The input wire is the one with the male pin on it. Do not mistake this for the output wires which are female terminated.

If you have a Rev3 harness:
You will feed this wire into the o2 input wire on the black 9 pin expansion port. This is pin #8 on the 9-pin connector (solid yellow wire). You will probably want to order a mating 9-pin connector and a pre-terminated wire from us since you have the opportunity to make this plug and play at this point.

One the 0-5 linear output signal (from your wideband unit) is routed to the o2 input wire on the Procede harness, you will need to set up the new Wideband AFR channel in your datalog settings. See attached.

Please note that the raw and converted min/max values shown below apply to a sensor that is calibrated to a sensor output that is calibrated to translate a 0-5v signal into an AFR reading of 10:1-20:1. Different wideband units may have different calibrations and the min/max values may have to be changed accordingly.

Assuming everything is set up properly, you should know be able to log AFR data (from your wideband) into the datalog channel (inappropriately) named "Actual Rear O2 Voltage"
Attached Images
 
Appreciate 0
      09-20-2012, 12:15 PM   #2
Jeff@TopGearSolutions
BimmerPost Supporting Vendor
Jeff@TopGearSolutions's Avatar
United_States
2715
Rep
58,716
Posts


Drives: C6 Z06, 09 335i, 10 335xi
Join Date: Dec 2008
Location: www.TopGearSolutions.com

iTrader: (37)

Definitely easy as long as the bung is welded in and you have the hardware
__________________
|Like us on Facebook||Evolution Racewerks| |Active Autowerke| |ETS| |Burger Tuning| |PURE Turbos| |Mishimoto||VRSF| |AWE| |Wagner|

|Holiday Sales All December!| |KW| |Spec| |ST Coilovers| |Koni| |Bilstein| |Borla| |Magnaflow| |AFE| |Fabspeed| |Injen| Up to 10% Off!
Appreciate 0
      09-20-2012, 05:05 PM   #3
JMARS
Not Baned
United_States
64
Rep
1,355
Posts

Drives: e92 Single-T
Join Date: Aug 2008
Location: Boca Raton, FL

iTrader: (5)

Thanks Shiv!!!!! This is exactly what i was looking for!
__________________
FFTEC 900 - 6466 | PR PI Stg4 | Motiv Tune/BB/FF | Spec Stg 2+ | Quaife LSD | DSS Half-shafts
VRSF Race IC | VRSF Charge Pipe | Evo Dual Oil Cooler | BC Coilover | To be continued...
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:39 PM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST