|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
N54 with RB's check something
|
|
12-18-2014, 01:35 AM | #1 |
Brigadier General
827
Rep 3,189
Posts |
N54 with RB's check something
Whats your vacuum reading of your cobb ap during idle?
RB or stock Last edited by Brule; 12-25-2014 at 11:31 PM.. Reason: new check |
12-18-2014, 01:51 AM | #2 |
Lieutenant General
4542
Rep 11,903
Posts |
All I see is black
|
Appreciate
0
|
12-18-2014, 02:03 AM | #3 |
Brigadier General
827
Rep 3,189
Posts |
You try and put your hands down there and film.
Just listen to the rattle and see if your RB's are the same. I'm at wits end and I'm going to as Rob for a new set |
Appreciate
0
|
12-18-2014, 03:25 AM | #5 |
Brigadier General
827
Rep 3,189
Posts |
|
Appreciate
0
|
12-18-2014, 05:17 AM | #6 |
Jedi samurai ninja turtle
619
Rep 3,021
Posts
Drives: X3 M40i 2018
Join Date: May 2012
Location: Sydney, Australia
|
Maybe tell us what you are doing with it? Sounds like rape?!
|
Appreciate
0
|
12-18-2014, 05:25 AM | #7 |
Major
374
Rep 1,392
Posts |
|
Appreciate
0
|
12-18-2014, 06:48 AM | #8 |
First Lieutenant
62
Rep 307
Posts |
I have been having the same issue ever since I have put mine on. I have tried everything I can. I've tried every adustment I could on the JB4. I've changed all vacuum lines. tested all solenoids and canisters all check good. Put vacuum on the wastegates and they close tight at 5.5hg. The only other option is to take them off and send them back to be checked by Rob but I can't afford to have my car down for months again.
|
Appreciate
0
|
12-18-2014, 08:12 AM | #9 |
Captain
58
Rep 610
Posts |
what about menu10 and 12 on the JB4? i'm a noob but I heard it can be adjusted to reduce rattle but will affect your throttle sensitivity
__________________
JB4 G5 ISO | BMS Backend Flash | Alpina B3 TCU Flash | AR Design Catless DP | BMS DCI | ER CP | Turbosmart Race Port BOV | Muffler Delete | H&R Sport Springs | BMS Cowl | BMW Performance Alcantara Wheel | M3 DCT Paddles | Muse Concept and Design Interior | 19" GTC-CX | M3 Lip Spoiler | Zieg CF Rear Diffuser | Flow Designs Front Lip | Black Grill | RGB LED Angel Eyes | 8000K HID |
|
Appreciate
0
|
12-19-2014, 04:32 AM | #10 | |
Brigadier General
827
Rep 3,189
Posts |
Quote:
I know exactly how pissed off you are. If the solenoids don't fix it i will be taking the turbos off. |
|
Appreciate
0
|
12-19-2014, 04:33 AM | #11 |
Brigadier General
827
Rep 3,189
Posts |
|
Appreciate
0
|
12-19-2014, 06:45 PM | #12 |
Private
2
Rep 85
Posts |
Mine are about 5000kms old and have started this too. Contacted Rob who was helpful and gave me a list of things to check. I had already repalced all vacuum lines and measured vacuum at canisteres and boost solenoids and it was all normal. Menu 10 makes very little difference across the spectrum of different values. I am going to isolate the turbo's one at a time to find which one it is and then swap the solenoids around to prove it is that before paying for new ones.
I hope that sorts it otherwise they have to be pulled out and they already cost me a packet to install The main reason to replace the OEM's was because they sounded like a tractor and figured may as go for the extra performance. |
Appreciate
0
|
12-20-2014, 01:59 AM | #14 |
Brigadier General
827
Rep 3,189
Posts |
This morning before work I pulled out vacuum canisters to check for leaks cracks.
Found one heat shield bolt with only 30% thread into the block. I dare say i have found the issue. The heat shield is sitting about 10mm off the block and still has clearance from the wastegate arm towards the front but you cant physically see the entire wastegate arm. The sound must just be from vibrating. Although I have spent 3 hours and 3 beers trying to get one bolt tightened unsuccessfully. It is behind front manifold center junction. Last edited by Brule; 12-20-2014 at 10:19 PM.. |
Appreciate
0
|
12-20-2014, 10:18 PM | #15 |
Brigadier General
827
Rep 3,189
Posts |
Got the heat shield bolt tightened. I Still have a rattle.
I have a big sound of vacuum sound releasing when I turn the car off is that normal with your cars? |
Appreciate
0
|
Bookmarks |
|
|