$10 paypal if you can tell me where this plug goes!

335imax · 12-07-2010, 08:08 AM

Still need help guys. Did an Intake manifold swap. When reassembling could not for the life of me figure out where this plug goes. There is just no place to plug it in, that I can see?! My DSC light is on after the intake manifold swap, so I am assuming it is DSC related. $10 paypal to the first person that can get this plug identified, (it is directly under the throttle body) and my DSC functional again!

Kevin@AKMotorwerk · 12-07-2010, 08:09 AM

is your mass air sensor plugged in? looks kinda like the plug for that

3002 tii · 12-07-2010, 08:24 AM

^^ WHS

This person did the same conversion and in the 3rd pic from the top, you see what appears to be the same plug going into the back of the intake box

http://www.zpost.com/forums/showthread.php?t=455180

dtc100 · 12-07-2010, 08:54 AM

I doubt it, could he even start the engine without the MAF plugged in? He only got the DSC code.

On a side note, can the same thing be done to a 328i? Where does the extra 45hp come from, I thought the N52 is maxxed out pretty much?

mthomas · 12-07-2010, 08:56 AM

MAF sensor on the back of the filter box

Kevin@AKMotorwerk · 12-07-2010, 09:07 AM

Quote:

Originally Posted by dtc100

I doubt it, could he even start the engine without the MAF plugged in? He only got the DSC code.

On a side note, can the same thing be done to a 328i? Where does the extra 45hp come from, I thought the N52 is maxxed out pretty much?

most cars will run with the mass air sensor unplugged,the computer goes into a default setting when the sensor is not detected, not that they will always run perfect, it depends on the temp's and all and what the factory set the car to run with at default without the sensor

3002 tii · 12-07-2010, 09:13 AM

Quote:

Originally Posted by dtc100

I doubt it, could he even start the engine without the MAF plugged in? He only got the DSC code.

On a side note, can the same thing be done to a 328i? Where does the extra 45hp come from, I thought the N52 is maxxed out pretty much?

yes, it can be done on both 325/328i.

not sure where you're getting the 45hp. if it's from the link i posted, that guy is also getting an AA tune on top of this so it'll be effectively comparing a stock 328 to a tuned 330i so he must be comparing difference in crank #s.

lore2486 · 12-07-2010, 09:19 AM

i am almost sure that is the plug for the DISA valves motors, on 328 with stock manifold there one thats just hanging next to the manifold and when you put a 330i manifold you need to plug that in. hope this helped

ps did you get your computer reprogramed?

it mihght also be a plug for the throtle but this is less posible

dtc100 · 12-07-2010, 09:20 AM

Quote:

Originally Posted by Dubbedown

yes, it can be done on both 325/328i.

not sure where you're getting the 45hp. if it's from the link i posted, that guy is also getting an AA tune on top of this so it'll be effectively comparing a stock 328 to a tuned 330i so he must be comparing difference in crank #s.

I understand he must also get it tuned, but he was doing this to his Z4. Was the Z4 similar to a 325i or a 328i?

BTW part of the reason I doubt that was the MAF connector was because it is very very hard to miss the MAF plug

335imax · 12-07-2010, 09:50 AM

It is not one of the plugs to the DISA motors. There are two of those type plugs and they are smaller. Both plugged in.
It is not the plug to the MAF. That one is larger, and also plugged in.
It is not the plug to the Throttle body, that one is larger and plugged in.

The only error on the dash is DSC disabled. So thats what I was thinking it went to...

dtc100 · 12-07-2010, 10:03 AM

Quote:

Originally Posted by 325imax

It is not one of the plugs to the DISA motors. There are two of those type plugs and they are smaller. Both plugged in.
It is not the plug to the MAF. That one is larger, and also plugged in.
It is not the plug to the Throttle body, that one is larger and plugged in.

The only error on the dash is DSC disabled. So thats what I was thinking it went to...

Was it actually plugged in before the swap? If you can't remember, look at the contacts if they look very oxidized it likely was not used before, the plug might not be needed. I am only guessing of course.

Do you plan to get it tuned? If so what is the estimated power gain from stock?

3002 tii · 12-07-2010, 10:18 AM

Quote:

Originally Posted by dtc100

I understand he must also get it tuned, but he was doing this to his Z4. Was the Z4 similar to a 325i or a 328i?

BTW part of the reason I doubt that was the MAF connector was because it is very very hard to miss the MAF plug

06-08 z4 non-m only came in 3.0i/3.0si which would be the equiv of 328i/330i.

335imax · 12-07-2010, 10:53 AM

Quote:

Originally Posted by dtc100

Was it actually plugged in before the swap? If you can't remember, look at the contacts if they look very oxidized it likely was not used before, the plug might not be needed. I am only guessing of course.

Do you plan to get it tuned? If so what is the estimated power gain from stock?

Usually plugs that are not used are capped. This one was not capped.

335imax · 12-07-2010, 12:23 PM

Looks like DubbeDown, has gotten me closer. It might go here See the RED CIRCLE! I will try this spot tonight, and if DubbedDown is correct. $10.00

dtc100 · 12-07-2010, 12:53 PM

Quote:

Originally Posted by Dubbedown

Quote:

Originally Posted by dtc100

I understand he must also get it tuned, but he was doing this to his Z4. Was the Z4 similar to a 325i or a 328i?

BTW part of the reason I doubt that was the MAF connector was because it is very very hard to miss the MAF plug

06-08 z4 non-m only came in 3.0i/3.0si which would be the equiv of 328i/330i.

So with the 3 stage swap and tune the 328i can have up to 45hp added basically for under $1,000? Any downside to such mod?

335imax · 12-07-2010, 01:37 PM

The price to do this is about $900 for parts
The software tune you need is at least $400.00 depending on vender.
The labor to do this is a two person job, and if I had to do it again, I would let a mechanic do the work. Its a one person pain in the a$$

So if your time is free, then $1300 gives you about 35 HP

325/528 · 12-12-2010, 03:24 PM

How did this work out?

335imax · 12-14-2010, 07:40 PM

The E90 can run without the Crankshaft Sensor, but poorly. The car goes into default limp mode. You get a Service Engine Light, and a Brake light. Along with a DSC Malfunction code. So, my problem was that the Crankshaft Sensor plug, was not plugged in!

It plugs into the crankshaft sensor, on the crankshaft.

12-07-2010, 08:08 AM	#1
335imax Second Lieutenant 44 Rep 210 Posts Drives: 2012 335i Join Date: Sep 2010 Location: Virginia iTrader: (1)	$10 paypal if you can tell me where this plug goes! Still need help guys. Did an Intake manifold swap. When reassembling could not for the life of me figure out where this plug goes. There is just no place to plug it in, that I can see?! My DSC light is on after the intake manifold swap, so I am assuming it is DSC related. $10 paypal to the first person that can get this plug identified, (it is directly under the throttle body) and my DSC functional again! __________________ M Performance Suspension
	Appreciate 0 Tweet Quote

12-07-2010, 08:09 AM	#2
Kevin@AKMotorwerk General 290 Rep 28,154 Posts Drives: THE GUY YOU LOVE TO HATE Join Date: Mar 2009 Location: hillsborough, nj iTrader: (1)	is your mass air sensor plugged in? looks kinda like the plug for that
	Appreciate 0 Quote

12-07-2010, 08:24 AM	#3
3002 tii Lieutenant General 2283 Rep 12,565 Posts Drives: Z4 M, X5, GX460 Join Date: Apr 2008 Location: CT iTrader: (99) Garage List F15 X5 xDrive35i [8.75] E86 Z4 M [10.00] F10 550i (Retired) [9.17] F25 X3 xDrive35i (R ... [9.43] E82 135is (Retired) [9.50] E85 Z4 M (Retired) [9.41] E90 328i xDrive (Re ... [9.25] E86 Z4 3.0si (Retired) [9.24]	^^ WHS This person did the same conversion and in the 3rd pic from the top, you see what appears to be the same plug going into the back of the intake box http://www.zpost.com/forums/showthread.php?t=455180 __________________ Follow for latest mods
	Appreciate 0 Quote

12-07-2010, 08:54 AM	#4
dtc100 Lieutenant Colonel 28 Rep 1,522 Posts Drives: 2011 E90 328i 6AT non-sport Join Date: Sep 2010 Location: Norcal iTrader: (0)	I doubt it, could he even start the engine without the MAF plugged in? He only got the DSC code. On a side note, can the same thing be done to a 328i? Where does the extra 45hp come from, I thought the N52 is maxxed out pretty much?
	Appreciate 0 Quote

12-07-2010, 08:56 AM	#5
mthomas Private First Class 5 Rep 156 Posts Drives: 2006 330xi Join Date: Feb 2010 Location: lNorth Shore, Lake Tahoe iTrader: (0)	MAF sensor on the back of the filter box
	Appreciate 0 Quote

12-07-2010, 09:19 AM	#8
lore2486 Lieutenant 77 Rep 560 Posts Drives: e92 AW/IR 328i Join Date: Sep 2009 Location: FL Pembroke iTrader: (1)	i am almost sure that is the plug for the DISA valves motors, on 328 with stock manifold there one thats just hanging next to the manifold and when you put a 330i manifold you need to plug that in. hope this helped ps did you get your computer reprogramed? it mihght also be a plug for the throtle but this is less posible __________________ 2016 bmw M4 YMB/SO Stock
	Appreciate 0 Quote

12-07-2010, 09:50 AM	#10
335imax Second Lieutenant 44 Rep 210 Posts Drives: 2012 335i Join Date: Sep 2010 Location: Virginia iTrader: (1)	Here is what it is not It is not one of the plugs to the DISA motors. There are two of those type plugs and they are smaller. Both plugged in. It is not the plug to the MAF. That one is larger, and also plugged in. It is not the plug to the Throttle body, that one is larger and plugged in. The only error on the dash is DSC disabled. So thats what I was thinking it went to... __________________ M Performance Suspension
	Appreciate 0 Quote

12-07-2010, 12:23 PM	#14
335imax Second Lieutenant 44 Rep 210 Posts Drives: 2012 335i Join Date: Sep 2010 Location: Virginia iTrader: (1)	Maybe this is it Looks like DubbeDown, has gotten me closer. It might go here See the RED CIRCLE! I will try this spot tonight, and if DubbedDown is correct. $10.00 Attached Images __________________ M Performance Suspension
	Appreciate 0 Quote

12-07-2010, 01:37 PM	#16
335imax Second Lieutenant 44 Rep 210 Posts Drives: 2012 335i Join Date: Sep 2010 Location: Virginia iTrader: (1)	Think its more like 35 HP The price to do this is about $900 for parts The software tune you need is at least $400.00 depending on vender. The labor to do this is a two person job, and if I had to do it again, I would let a mechanic do the work. Its a one person pain in the a$$ So if your time is free, then $1300 gives you about 35 HP __________________ M Performance Suspension
	Appreciate 0 Quote

12-12-2010, 03:24 PM	#17
325/528 Second Lieutenant 23 Rep 278 Posts Drives: pinto Join Date: Jan 2008 Location: lost soul iTrader: (7)	How did this work out?
	Appreciate 0 Quote

12-14-2010, 07:40 PM	#18
335imax Second Lieutenant 44 Rep 210 Posts Drives: 2012 335i Join Date: Sep 2010 Location: Virginia iTrader: (1)	This plug goes to the Crankshaft Sensor The E90 can run without the Crankshaft Sensor, but poorly. The car goes into default limp mode. You get a Service Engine Light, and a Brake light. Along with a DSC Malfunction code. So, my problem was that the Crankshaft Sensor plug, was not plugged in! It plugs into the crankshaft sensor, on the crankshaft. __________________ M Performance Suspension
	Appreciate 0 Quote