Running Devils own meth nozzle without scew in filter?

robc1976 · 06-21-2013, 12:03 AM

Anyone ever try to run a devils own meth nozzle without the screw in filter? I can see where this may be a slight restriction and I don't need a filter in the nozzle....have one in the tank.

Sick335 · 06-21-2013, 04:15 PM

Hey Rob,

Ive had the tank for a few months now, and im starting to have a reeeeeeally hard time opening the top to fill it with meth. Are you having the same problem? I literally have to use a screw driver to pry it open.

robc1976 · 06-21-2013, 04:49 PM

Quote:

Originally Posted by Sick335

Hey Rob,

Ive had the tank for a few months now, and im starting to have a reeeeeeally hard time opening the top to fill it with meth. Are you having the same problem? I literally have to use a screw driver to pry it open.

ROFLMAO! Same thing I had to do...the task when you seal it kinda pulls up and flexes and over time stays that way like a fuel cell dies. All you have to do is grind the tabs down on the top you will see the 3 metal tabs...just grind then down a bit. I did this and open them it with one hand now. I was getting so pissed when I had to pry it lol!

robc1976 · 06-21-2013, 04:52 PM

Also with the filter meth flow was at 270 on the JB4 gauge high-Jack, without the filter it is at 300 instantly.

3000GT MR · 06-21-2013, 04:56 PM

I would keep it installed. If anything down stream of the tank produces FOD then your screwed. Port the filter core or go bigger if you need to

robc1976 · 06-22-2013, 09:08 PM

Quote:

Originally Posted by 3000GT MR

I would keep it installed. If anything down stream of the tank produces FOD then your screwed. Port the filter core or go bigger if you need to

I am running a DO14 so can't go bigger. Only thing down stream is south in tank filter...with me being 4-AN fitting with stainless I think I am safe.

3000GT MR · 06-22-2013, 09:14 PM

Quote:

Originally Posted by robc1976

Quote:

Originally Posted by 3000GT MR

I would keep it installed. If anything down stream of the tank produces FOD then your screwed. Port the filter core or go bigger if you need to

I am running a DO14 so can't go bigger. Only thing down stream is south in tank filter...with me being 4-AN fitting with stainless I think I am safe.

My experience with meth. I've seen little chips from the pump, random oring material etc. I've always found stuff in the nozzle filter even with 2 inline filters. If you have a D014 is recommend 2 smaller nozzles.

Sick335 · 06-24-2013, 11:57 AM

Quote:

Originally Posted by robc1976

Also with the filter meth flow was at 270 on the JB4 gauge high-Jack, without the filter it is at 300 instantly.

Yup same thing... It took me good 15 minutes to open the tank yesterday... madness

robc1976 · 06-24-2013, 01:27 PM

Quote:

Originally Posted by 3000GT MR

My experience with meth. I've seen little chips from the pump, random oring material etc. I've always found stuff in the nozzle filter even with 2 inline filters. If you have a D014 is recommend 2 smaller nozzles.

I had 2 smallernozzles and meth response was not add good....with the selonoid connected directly to the nozzle holder the response is great....can't do that with dual nozzle. Dual nozzle will allow for great optimization though.

robc1976 · 06-24-2013, 01:28 PM

Quote:

Originally Posted by Sick335

Yup same thing... It took me good 15 minutes to open the tank yesterday... madness

shave it like I stated above...I bet you where PISSED!

Jeff@TopGearSolutions · 06-24-2013, 01:31 PM

I'd leave it in. I dont think the extra 10% of flow is worth the risk especially if you have adequate flow for your setup. Those filters do catch more then you think. They are the last line in defense

robc1976 · 06-24-2013, 01:40 PM

Quote:

Originally Posted by Jeff@TopGearSolutions

I'd leave it in. I dont think the extra 10% of flow is worth the risk especially if you have adequate flow for your setup. Those filters do catch more then you think. They are the last line in defense

I may go back....but I have a in tank filter also

Sick335 · 06-25-2013, 07:05 AM

Quote:

Originally Posted by robc1976

shave it like I stated above...I bet you where PISSED!

Did you shave the cap or the metal part inside the tank? Can you post a pic of how much you shaved off? I dont even know if i'll be able to open the tank again, each time its harder and harder to do...

robc1976 · 06-25-2013, 12:16 PM

Quote:

Originally Posted by Sick335

Did you shave the cap or the metal part inside the tank? Can you post a pic of how much you shaved off? I dont even know if i'll be able to open the tank again, each time its harder and harder to do...

I will post pics in a few!

3000GT MR · 06-25-2013, 01:33 PM

Quote:

Originally Posted by robc1976

Quote:

Originally Posted by 3000GT MR

My experience with meth. I've seen little chips from the pump, random oring material etc. I've always found stuff in the nozzle filter even with 2 inline filters. If you have a D014 is recommend 2 smaller nozzles.

I had 2 smallernozzles and meth response was not add good....with the selonoid connected directly to the nozzle holder the response is great....can't do that with dual nozzle. Dual nozzle will allow for great optimization though.

Man you give up to easy. Hook solenoid to a Tee fitting with 2 1inch hoses connecting each nozzle which would roughly put you at 10&2 O'clock positions. ;-)

Sick335 · 06-25-2013, 03:49 PM

Quote:

Originally Posted by robc1976

I will post pics in a few!

Appreciate it

enrita · 06-25-2013, 04:28 PM

Get a filter after the tank before the pump.

Sick335 · 06-25-2013, 04:38 PM

Quote:

Originally Posted by enrita

Get a filter after the tank before the pump.

I run 2 filters, inside tank, pre-solenoid

enrita · 06-25-2013, 04:42 PM

Quote:

Originally Posted by Sick335

I run 2 filters, inside tank, pre-solenoid

Are you collecting the alcohol at bars floors?

Sick335 · 06-25-2013, 04:44 PM

Quote:

Originally Posted by enrita

Are you collecting the alcohol at bars floors?

lolwut?

enrita · 06-25-2013, 04:48 PM

Quote:

Originally Posted by Sick335

lolwut?

LoL you got 2 filters. Alcohol or meth is pretty pure so dont see why you need so much filtering. I checked my aem filter and after 1 year it was clean.

Sick335 · 06-25-2013, 04:59 PM

Quote:

Originally Posted by enrita

LoL you got 2 filters. Alcohol or meth is pretty pure so dont see why you need so much filtering. I checked my aem filter and after 1 year it was clean.

We removed my nozzles and they were clogged to shit last time. Little filtering never hurt nobody, my flow is still 270+ at WOT

06-21-2013, 12:03 AM	#1
robc1976 DIYER 614 Rep 5,521 Posts Drives: E90 335i Join Date: Mar 2012 Location: Illinois iTrader: (14)	Running Devils own meth nozzle without scew in filter? Anyone ever try to run a devils own meth nozzle without the screw in filter? I can see where this may be a slight restriction and I don't need a filter in the nozzle....have one in the tank. __________________ JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
	Appreciate 0 Tweet Quote

06-21-2013, 04:15 PM	#2
Sick335 Major 88 Rep 1,174 Posts Drives: 335i / X6M Join Date: Oct 2011 Location: Woodland Hills, CA iTrader: (2)	Hey Rob, Ive had the tank for a few months now, and im starting to have a reeeeeeally hard time opening the top to fill it with meth. Are you having the same problem? I literally have to use a screw driver to pry it open.
	Appreciate 0 Quote

06-21-2013, 04:52 PM	#4
robc1976 DIYER 614 Rep 5,521 Posts Drives: E90 335i Join Date: Mar 2012 Location: Illinois iTrader: (14)	Also with the filter meth flow was at 270 on the JB4 gauge high-Jack, without the filter it is at 300 instantly. __________________ JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
	Appreciate 0 Quote

06-21-2013, 04:56 PM	#5
3000GT MR Major 265 Rep 1,392 Posts Drives: 09 335i/3000gt vr4 Join Date: Jun 2012 Location: Sav GA iTrader: (6)	I would keep it installed. If anything down stream of the tank produces FOD then your screwed. Port the filter core or go bigger if you need to __________________ Have a single turbo and/or tired of burning up O2 sensors? Ask me about the new ADV O2 sensor retro kits! 335i 2010 e92 M-sport Mods: VM Top mount 6466, Aquamist HSF4 w/custom direct port. VRSF IC + Exhaust 335i 2009 e90 665RWHP VFF900 ST RIP .
	Appreciate 0 Quote

06-24-2013, 01:31 PM	#11
Jeff@TopGearSolutions 3441 Rep 79,211 Posts Drives: C6 Z06, 09 335i, 10 335xi Join Date: Dec 2008 Location: www.TopGearSolutions.com iTrader: (37)	I'd leave it in. I dont think the extra 10% of flow is worth the risk especially if you have adequate flow for your setup. Those filters do catch more then you think. They are the last line in defense
	Appreciate 0 Quote

06-25-2013, 04:28 PM	#17
enrita Major General 161 Rep 7,377 Posts Drives: 335i - Big turbos Join Date: Sep 2008 Location: Italian in Sweden iTrader: (0)	Get a filter after the tank before the pump. __________________ 07 335i AT - MOTIV 750 - MHD E85 BMS flash - BMS PI - JB4G5 - Okada Coils - NGK 5992 Plugs - Helix IC - Snow Stg. 3 - Stett CP - Custom midpipes with 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - LUX H8 - Level 10 AT upgrade
	Appreciate 0 Quote