E90Post
 


TNT Racewerks
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > DIY Guides > DIY: E9X ACC Retrofit



Reply
 
Thread Tools Search this Thread
      05-21-2023, 07:05 AM   #507
Mr-Toast001
New Member
Mr-Toast001's Avatar
3
Rep
14
Posts

Drives: BMW 335xi
Join Date: Oct 2021
Location: Switzerland

iTrader: (0)

Quote:
Originally Posted by iTudor View Post
Thanks man. Can confirm this is correct. It is also quiete obvious as soon as you remove the fusebox.

In my case, fuse 21 was free and fuse 65 was already taken (cabel color was also red-yellow). I cheked the whole internet and it was stated everywhere, that F65 should be LDM Module and nothing else. So I removed the pin and put the pin of the LDM Module into F65.
Turns out that I removed power from the gear indicator of my auto transmission (the light beside the P-R-N-D). I now use fuse 64 for the gear indicator. This should be for the OBD 2 Plug but the pin position was free in my case.

I also had to modify the F-Bracket for the ACC a little bit since the pre-LCI version is discontinued (I ordered the pre-LCI version and got the LCI version; even though the sticker on the part stated the pre-LCI part number 66316769269, the stamped in part number was the one from the LCI 66316789935; never had something like this before).

Everthing works fine for me. Only thing I get is error C998 in BimmerLink (SZL: Error for SZL: LWS error: signal or value below threshold. Wheel tolerance adjustment <-5%: F-CAN Wheel tolerance adjustment, communication with DSC). I don't know if it's an error with the SZL (which I replaced completely) or if it is something else. Maybe I switch back to the old SZL at some point and only replace the cruise control stalk. The error does not come up when I scan the car with ISTA tough.
Appreciate 1
iTudor3.00
      05-22-2023, 02:00 AM   #508
iTudor
New Member
3
Rep
12
Posts

Drives: BMW E91 330D Manual
Join Date: Feb 2023
Location: Irun

iTrader: (0)

Quote:
Originally Posted by Mr-Toast001 View Post
Thanks man. Can confirm this is correct. It is also quiete obvious as soon as you remove the fusebox.

In my case, fuse 21 was free and fuse 65 was already taken (cabel color was also red-yellow). I cheked the whole internet and it was stated everywhere, that F65 should be LDM Module and nothing else. So I removed the pin and put the pin of the LDM Module into F65.
Turns out that I removed power from the gear indicator of my auto transmission (the light beside the P-R-N-D). I now use fuse 64 for the gear indicator. This should be for the OBD 2 Plug but the pin position was free in my case.

I also had to modify the F-Bracket for the ACC a little bit since the pre-LCI version is discontinued (I ordered the pre-LCI version and got the LCI version; even though the sticker on the part stated the pre-LCI part number 66316769269, the stamped in part number was the one from the LCI 66316789935; never had something like this before).

Everthing works fine for me. Only thing I get is error C998 in BimmerLink (SZL: Error for SZL: LWS error: signal or value below threshold. Wheel tolerance adjustment <-5%: F-CAN Wheel tolerance adjustment, communication with DSC). I don't know if it's an error with the SZL (which I replaced completely) or if it is something else. Maybe I switch back to the old SZL at some point and only replace the cruise control stalk. The error does not come up when I scan the car with ISTA tough.
In my case I only used the stalk from the new SZL and fitted it into my cars original SZL, no errors anywhere.

anyways I trust more ISTA than BimmerLink, for me it shows sometimes weird faults that are not in ISTA, and everything works fine anyways.
Appreciate 0
      05-29-2023, 01:40 PM   #509
Mr-Toast001
New Member
Mr-Toast001's Avatar
3
Rep
14
Posts

Drives: BMW 335xi
Join Date: Oct 2021
Location: Switzerland

iTrader: (0)

Quote:
Originally Posted by iTudor View Post
I trust more ISTA than BimmerLink, for me it shows sometimes weird faults that are not in ISTA, and everything works fine anyways.
I thought so too. But I basically had three fault codes in BimmerLink, while I only had one in ISTA. Two faults where due to some Sensors I disconnected and one was this weird SZL issue. I know for sure, that I have at least two faul codes for the sensors (because I personally diconnected them). Since ISTA was only showing one, I think something is not good with my ISTA installation and therefore trust more BimmerLink.

However, I switched back to my old SZL and only replaced the stalk --> no errors anymore.
I think the reason for the error was, that I turned the steering wheel sensor of the new/replacement SZL a coule of times in one direction to see if it comes to a stop and to see if it was centered. Since there was no stop, I thought there was no center and I just lined up the arrows on the plastic and slammed it into the car. Maybe the steering angle sensor/disc was off by two or three full turns and I should have turned the disc back to it's original position.
Appreciate 0
      06-02-2023, 06:47 AM   #510
pmorg4
Private
28
Rep
99
Posts

Drives: BMW 335i Touring LCI
Join Date: Nov 2020
Location: Surrey, UK

iTrader: (0)

Where are you guys finding SZL for ACC? There seem to be very few around, especially for E91 with rear wiper (noting that the stalk can of course be transferred across to my old SZL).
Appreciate 0
      06-02-2023, 09:46 AM   #511
iTudor
New Member
3
Rep
12
Posts

Drives: BMW E91 330D Manual
Join Date: Feb 2023
Location: Irun

iTrader: (0)

Quote:
Originally Posted by pmorg4 View Post
Where are you guys finding SZL for ACC? There seem to be very few around, especially for E91 with rear wiper (noting that the stalk can of course be transferred across to my old SZL).
lots of patience and searching everywhere

I found my entire SZL for 60€ in some french scrapyard, they wouldnt ship to spain, had to ship it to a friend from france, then to spain, but it was worth it. I only used the stalk, installed into my own SZL, since my car is E91 and it was an E90 SZL.

The way I found this one, was through google images about ACC stalk, untill reached way down to one that looked like a scrapyard photo, and voila!
Appreciate 0
      06-04-2023, 10:48 AM   #512
pmorg4
Private
28
Rep
99
Posts

Drives: BMW 335i Touring LCI
Join Date: Nov 2020
Location: Surrey, UK

iTrader: (0)

Thanks! I guess I'd better keep searching then! I have ACC fitted to my second E91 and in both cases I've been using it without the ACC stalk meaning I can't adjust the distance. It otherwise works perfectly without the ACC stalk.
Appreciate 0
      07-01-2023, 03:45 PM   #513
Nickco43
Lieutenant Colonel
Nickco43's Avatar
1544
Rep
1,942
Posts

Drives: 2017 BMW 540i
Join Date: Apr 2018
Location: Denver, CO

iTrader: (1)

Garage List
2017 BMW  [0.00]
I recently bought a E92 and of course it needs ACC.

Has anyone fitted ACC to a M3?
Appreciate 0
      07-01-2023, 06:28 PM   #514
colorado.e9x
eBay Special
colorado.e9x's Avatar
United_States
3516
Rep
3,151
Posts

Drives: E90 330xi
Join Date: Feb 2018
Location: Western Slope, Colorado

iTrader: (1)

Garage List
2006 BMW 330xi  [10.00]
2007 BMW 328xi  [9.50]
I have no input on the M3 as far as technicals go. There's an air dam/shroud that will most likely need to be cut along with the lower grille.

I'm still doing my retrofit with an M3 style bumper (lifes gotten in the way oops). Theres some interference with the lower grille as expected. Unfortunately it looks like there will need to be a cutout for the whole unit and not just the spherical portion. The square part appears to be flush if not slightly protruding from the grille mesh. Ugly.

With the longer nose of the M3 you might not have to worry about that, I'm not sure
__________________
Common sense is a flower that does not bloom in everyone's garden
Appreciate 0
      07-10-2023, 10:24 AM   #515
Nodi19
New Member
0
Rep
8
Posts

Drives: BMW E90 325i
Join Date: Jan 2021
Location: Hungary

iTrader: (0)

Quote:
Originally Posted by colorado.e9x View Post
I have no input on the M3 as far as technicals go. There's an air dam/shroud that will most likely need to be cut along with the lower grille.

I'm still doing my retrofit with an M3 style bumper (lifes gotten in the way oops). Theres some interference with the lower grille as expected. Unfortunately it looks like there will need to be a cutout for the whole unit and not just the spherical portion. The square part appears to be flush if not slightly protruding from the grille mesh. Ugly.

With the longer nose of the M3 you might not have to worry about that, I'm not sure
Hi! I am in the same boat. I think there is no exigent way to install the acc sensor on this bumper, but if you find solution please upload the result. Thanks
Appreciate 0
      08-01-2023, 01:06 PM   #516
maszter
Registered
0
Rep
3
Posts

Drives: E92 335xd (built from 330xd)
Join Date: Aug 2023
Location: Hungary

iTrader: (0)

Quote:
Originally Posted by Mr-Toast001 View Post
Thanks man. Can confirm this is correct. It is also quiete obvious as soon as you remove the fusebox.

In my case, fuse 21 was free and fuse 65 was already taken (cabel color was also red-yellow). I cheked the whole internet and it was stated everywhere, that F65 should be LDM Module and nothing else. So I removed the pin and put the pin of the LDM Module into F65.
Turns out that I removed power from the gear indicator of my auto transmission (the light beside the P-R-N-D). I now use fuse 64 for the gear indicator. This should be for the OBD 2 Plug but the pin position was free in my case.

I also had to modify the F-Bracket for the ACC a little bit since the pre-LCI version is discontinued (I ordered the pre-LCI version and got the LCI version; even though the sticker on the part stated the pre-LCI part number 66316769269, the stamped in part number was the one from the LCI 66316789935; never had something like this before).

Everthing works fine for me. Only thing I get is error C998 in BimmerLink (SZL: Error for SZL: LWS error: signal or value below threshold. Wheel tolerance adjustment <-5%: F-CAN Wheel tolerance adjustment, communication with DSC). I don't know if it's an error with the SZL (which I replaced completely) or if it is something else. Maybe I switch back to the old SZL at some point and only replace the cruise control stalk. The error does not come up when I scan the car with ISTA tough.
Can you tell me how did you modified the F-Bracket please ? I am having the same issue right now on my pre-lci E92. Thanks
Appreciate 0
      08-27-2023, 04:58 PM   #517
Mr-Toast001
New Member
Mr-Toast001's Avatar
3
Rep
14
Posts

Drives: BMW 335xi
Join Date: Oct 2021
Location: Switzerland

iTrader: (0)

I basically mounted the plate (which holds the ACC sensor) to the F-Bracket with the two bolts that fitted. Then I used a drill to put a hole where the third hole should have been (I think it was exactly at/in the end of the brackets groove). I had to use a nut to mount the plate since there was nothing at the backside of the bracket to put a helicoil or so.
If you are good at welding, you can maybe weld something to the backside of the bracket and put a helicoil. That would be as OEM as it could get nowadays.
Appreciate 0
      09-04-2023, 08:00 AM   #518
Nodi19
New Member
0
Rep
8
Posts

Drives: BMW E90 325i
Join Date: Jan 2021
Location: Hungary

iTrader: (0)

Hi!
Is there anybody besides me who uses acc with normal cruise control stalk? I tried to code the initial distance(02) but when I set a new value in nettodata ncs gives me errors. I also tried another way, I disassembled the ACC2E90.C47 and set new values ​​(00, 01) and after that I tried to code with the new value. Coding was successfully, but when I go for a test drive and turn on acc it always uses 02 as initial value.
Appreciate 0
      09-13-2023, 05:15 AM   #519
Mr-Toast001
New Member
Mr-Toast001's Avatar
3
Rep
14
Posts

Drives: BMW 335xi
Join Date: Oct 2021
Location: Switzerland

iTrader: (0)

Unfotunately I cannot help you, but I would be also interested.
What do you mean when you say you disassembled the ACC2E90.C47?

Do you think it would be possible to check the e60 ACC file and look for the code which diables the ACC and enables normal cruise control (in e60 you can hold the distance switch on the stalk for 3 seconds to disable ACC)?
Appreciate 0
      09-18-2023, 09:31 AM   #520
Nodi19
New Member
0
Rep
8
Posts

Drives: BMW E90 325i
Join Date: Jan 2021
Location: Hungary

iTrader: (0)

Quote:
Originally Posted by Mr-Toast001 View Post
Unfotunately I cannot help you, but I would be also interested.
What do you mean when you say you disassembled the ACC2E90.C47?

Do you think it would be possible to check the e60 ACC file and look for the code which diables the ACC and enables normal cruise control (in e60 you can hold the distance switch on the stalk for 3 seconds to disable ACC)?
I mean edited acc2e90.c47 file, I added 3 new parameters, but did not work. If I enabled the acc, always started with 3 bars. Meanwhile i got an acc stalk, so now I can adjust the distance.
Appreciate 0
      09-18-2023, 06:19 PM   #521
Runnin'Rich
Private First Class
132
Rep
203
Posts

Drives: 2009MY E91 328Xi 6MT
Join Date: Sep 2020
Location: British Columbia Canada

iTrader: (0)

I took the ACC stalk off the original SZL and transplanted it onto my heated steering wheel SZL.
You don’t need to look for one specifically with a rear wiper, just swap it over
Appreciate 0
      09-30-2023, 04:22 AM   #522
pmorg4
Private
28
Rep
99
Posts

Drives: BMW 335i Touring LCI
Join Date: Nov 2020
Location: Surrey, UK

iTrader: (0)

Quote:
Originally Posted by Nodi19 View Post
Hi!
Is there anybody besides me who uses acc with normal cruise control stalk? I tried to code the initial distance(02) but when I set a new value in nettodata ncs gives me errors. I also tried another way, I disassembled the ACC2E90.C47 and set new values ​​(00, 01) and after that I tried to code with the new value. Coding was successfully, but when I go for a test drive and turn on acc it always uses 02 as initial value.
I had exactly the same issue, running with a normal stalk and I couldn't get the default distance to decrease below 3 bars despite trying various coding options.

I finally managed to source a SZL with ACC stalk, fitted it and coded everything (including VIN in the SZL) but my indicators and wipers didn't work. I'm not sure if it's because the SZL was from an older pre-LCI car, maybe it would have worked with a software update but I didn't try. I instead swapped over the ACC stalk to my existing SZL and all is now working perfectly
Appreciate 0
      09-30-2023, 06:01 PM   #523
Jellepepe
Registered
5
Rep
4
Posts

Drives: BMW E90 320d individual
Join Date: Feb 2021
Location: Netherlands

iTrader: (0)

Quote:
Originally Posted by hupchye View Post
Unfortunately, all the interested members had dropped this retrofit due to its difficulties and complexity (ACC/Stop&Go in 4cyl E9x).
I believe I tried contacting you back in 2021 already at some point but failed.
I now have all the parts (6cyl DSC, all ACC parts, etc.) to install ACC on my 320d. I also already have an esp32 on my K-can for a different project, adding one to the PT-Can would be easy.

Would you be willing to share the relevant (PT-)Can signals you found / are using to make the ACC work? That would save me a lot of time reverse engineering the signals.
Would also be more than happy to help look into adding stop and go properly, including potentially adding additional radars/sensors

Cheers!
Appreciate 0
      09-30-2023, 06:19 PM   #524
hupchye
Private First Class
hupchye's Avatar
Malaysia
76
Rep
111
Posts

Drives: 2010 BMW 320i E92
Join Date: Jan 2020
Location: Malaysia

iTrader: (0)

Garage List
Quote:
Originally Posted by Jellepepe View Post
I believe I tried contacting you back in 2021 already at some point but failed.
I now have all the parts (6cyl DSC, all ACC parts, etc.) to install ACC on my 320d. I also already have an esp32 on my K-can for a different project, adding one to the PT-Can would be easy.

Would you be willing to share the relevant (PT-)Can signals you found / are using to make the ACC work? That would save me a lot of time reverse engineering the signals.
Would also be more than happy to help look into adding stop and go properly, including potentially adding additional radars/sensors

Cheers!
Hi, no problem at all. Until today had assisted few members on this and so far only ONE succeeded. You can contact me at hupchye@hotmail.com direct.
Appreciate 1
      11-12-2023, 08:30 PM   #525
shannon1
Private First Class
shannon1's Avatar
Australia
657
Rep
187
Posts

Drives: 2007 E91 323i M-Sport
Join Date: Jun 2019
Location: Brisbane, Australia

iTrader: (0)

Garage List
After a long time coming, I've finally completed my ACC retrofit on my '07 E91 323i. A few hiccups along the way but worked through them all with this sites and everyone's advice. So happy its finally done and loving it .
Appreciate 1
      12-06-2023, 08:23 PM   #526
Adrian052
New Member
0
Rep
6
Posts

Drives: Bmw 335D
Join Date: Mar 2023
Location: Bay Area, CA

iTrader: (0)

Anyone know if a e60 or similar radar would work? They look about the same for the eye test. I ask….well because the e90 ones are hard to find.
Appreciate 0
      12-08-2023, 08:28 AM   #527
pmorg4
Private
28
Rep
99
Posts

Drives: BMW 335i Touring LCI
Join Date: Nov 2020
Location: Surrey, UK

iTrader: (0)

Quote:
Originally Posted by Adrian052 View Post
Anyone know if a e60 or similar radar would work? They look about the same for the eye test. I ask….well because the e90 ones are hard to find.
There was some discussion on this earlier in the thread, and the short answer is no. The hardware is similar (maybe even the same) but the internal software is different and no-one has figured out how to change it between E60 and E90.
Appreciate 0
      12-09-2023, 07:23 AM   #528
KoktGrus
New Member
3
Rep
12
Posts

Drives: 535d 2009
Join Date: Aug 2019
Location: Sweden

iTrader: (0)

Quote:
Originally Posted by Mr-Toast001 View Post
Thanks man. Can confirm this is correct. It is also quiete obvious as soon as you remove the fusebox.

In my case, fuse 21 was free and fuse 65 was already taken (cabel color was also red-yellow). I cheked the whole internet and it was stated everywhere, that F65 should be LDM Module and nothing else. So I removed the pin and put the pin of the LDM Module into F65.
Turns out that I removed power from the gear indicator of my auto transmission (the light beside the P-R-N-D). I now use fuse 64 for the gear indicator. This should be for the OBD 2 Plug but the pin position was free in my case.

I also had to modify the F-Bracket for the ACC a little bit since the pre-LCI version is discontinued (I ordered the pre-LCI version and got the LCI version; even though the sticker on the part stated the pre-LCI part number 66316769269, the stamped in part number was the one from the LCI 66316789935; never had something like this before).

Everthing works fine for me. Only thing I get is error C998 in BimmerLink (SZL: Error for SZL: LWS error: signal or value below threshold. Wheel tolerance adjustment <-5%: F-CAN Wheel tolerance adjustment, communication with DSC). I don't know if it's an error with the SZL (which I replaced completely) or if it is something else. Maybe I switch back to the old SZL at some point and only replace the cruise control stalk. The error does not come up when I scan the car with ISTA tough.
I managed to get this LCI-console as well.
Was drilling that hole only thing you had to do? Did it fit correctly then? Got pictures?

I’m making a custom 66316769270 as one of my sensors mounts are damaged and want to use the 4th one. Then I can compensate for the wrong hole placement of the fastener at the 66316789935. Attaching a picture of the original 66316769270 to the left and the custom one to the right.

Very strange that the 66316769270 should fit both LCI and pre-LCI!
Name:  IMG_8323.jpg
Views: 641
Size:  122.6 KB

Last edited by KoktGrus; 12-09-2023 at 10:28 AM..
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 05:23 PM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST