|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
I cloned my MSV70 DME
|
|
12-19-2018, 07:32 AM | #2069 |
Captain
253
Rep 775
Posts |
For one brick yes. This particular one I ended up overwriting the boot sector and it got stuck in a loop and wasn’t responsive to any commands
|
Appreciate
0
|
12-19-2018, 11:57 AM | #2070 | |
Brigadier General
2440
Rep 4,331
Posts |
Quote:
I wanted to get the IM manifold on, the DME flashed and the 330 euro software in my trans controller before I attempted a full car update. |
|
Appreciate
0
|
12-28-2018, 07:41 AM | #2073 |
Brigadier General
2440
Rep 4,331
Posts |
got everything done yesterday. Had some slight issues with the batch file not copying files, but that may very well have been my win7 install and some permissions things.
I didn't feel confident in flashing it myself manually, so I just copied the files where the batch file wanted them and ran it. worked flawlessly after that. RSA delete took about 30 minutes. 328-330 file took about 5 hassmaschine is my hero. |
Appreciate
1
bluewater328625.50 |
12-28-2018, 03:29 PM | #2075 |
Brigadier General
2440
Rep 4,331
Posts |
it's in the default locations.
I ran it as administrator right from the first try. it simply wouldn't copy the files. The directories were there. a simple copy/paste and I ran the batch file again and it worked fine. way less scary than setting up winkfp myself. a quick 0-60 timer today proved that it did something. 7.1 to 60. not bad for a station wagon. |
Appreciate
1
Barrique91395.50 |
12-29-2018, 03:44 AM | #2076 | |
Colonel
626
Rep 2,100
Posts |
Quote:
If this is the wrong place, please PM me. |
|
Appreciate
0
|
12-30-2018, 09:13 AM | #2077 |
Brigadier General
2440
Rep 4,331
Posts |
just that if the batch file fails with a "file missing" error, look in it and just copy paste the files it wants to the directories.
other than that issue I had no problems with the winkfp parts of it. In swapping my manifold I found that my 328 PCV hose had two outlets, but my 330 intake had only one nipple. The hose was previously broken by somebody, so I replaced the entire thing with a piece of 3/4 hose slipped over the cut off quick connects. I probably won't bother ordering the correct one. |
Appreciate
1
bluewater328625.50 |
01-03-2019, 01:30 AM | #2078 |
Colonel
626
Rep 2,100
Posts |
Well, did the deed, install went great. Found out they removed that 4-port wiring hub for the PCV heater (or oil bladder for the 330i) as part of the "recall" process.
Went to do the flash and while both the RSA Delete and 330 flash reported "programming ok" I am now no longer able to test DISAs. That and I have a 2FA3 error (though from what I read that happens when you reprogram DME). Car seems to run fine, but the DISA test failure makes me wonder since it was working just before the flash. |
Appreciate
0
|
01-06-2019, 08:53 PM | #2079 | |
Colonel
626
Rep 2,100
Posts |
Quote:
I just found some instructions back on page 83 and I'll try and remove the 002FA3 code. I'd recommend resetting adaptations after the 3IM swap as the car pulled so much harder once I had done that. Give the car a chance to breathe the new air! Mahalo again to hassmachine/rjahl/Terra and all the bimmerlabs folks who contributed to the community and flash. Debating trying the MAF-less flash to see if there are more butt gains. |
|
Appreciate
0
|
01-08-2019, 08:25 PM | #2080 |
Second Lieutenant
99
Rep 237
Posts |
Hi Guys, i have just bought my 1st e90. Have had quite a few e46 and e39s before. My new car is a 323i Japan spec. I am new to the forum so please forgive me if I have posted this in the wrong place. I have just changed my manifold from 2 stage to 3 stage and was wanting to flash a 325i tune into my car. I've found a file on Bimmerlabs site but it says it is a stock tune. Does anybody know if this is actually "stock" or has it been modified to suit the 3 stage manifold?? I tried to look for more info on what it actually is but maybe i missed something? If someone could explain how it works that would be great. Thanks.
|
Appreciate
0
|
01-08-2019, 08:33 PM | #2081 | |
Colonel
626
Rep 2,100
Posts |
Quote:
|
|
Appreciate
0
|
01-08-2019, 08:53 PM | #2082 |
Second Lieutenant
99
Rep 237
Posts |
Thanks for the quick reply. Yes i created a new project but there is only 1 standard file available and i can't see where it says what it is. It just gives a ZB HW and software id number when i click on "detail"
|
Appreciate
0
|
01-08-2019, 09:17 PM | #2084 |
Second Lieutenant
99
Rep 237
Posts |
Thanks for that. I see the issue now. Mine only shows the RSA delete file in standard files which must mean there is nothing available for my N52B25 engine. i read on here of a guy with a 523i flashing to 525i so maybe it is possible? Does anybody know how i could find out?
Last edited by N52bigblock; 01-08-2019 at 09:19 PM.. Reason: Spelling |
Appreciate
0
|
01-08-2019, 09:22 PM | #2085 |
Colonel
626
Rep 2,100
Posts |
Just put the request in and they will get to you. It's only a few folks putting in spare time, so be patient. Sometimes they come into the thread here and get to your item sooner if they can. Who knows, maybe they need to do some research or need to do something custom since yours is a JDM version.
|
Appreciate
0
|
01-09-2019, 12:38 AM | #2087 |
Colonel
626
Rep 2,100
Posts |
|
Appreciate
0
|
01-09-2019, 01:11 AM | #2088 |
Second Lieutenant
99
Rep 237
Posts |
I put in a request. So now i wait patiently. I also did a bit of research. My 323i has a pitiful 177hp, the n52b25 in the 325i has 218hp. According to ETK, everything is the same, (exhaust manifold and system, camshafts etc) The only difference seems to be my car only has a 2 stage intake manifold but the 325i has the 3 stage. A 41hp gain would pretty damn good if possible. I wouldn't mind at all if i had to pay them for it!
|
Appreciate
0
|
01-30-2019, 12:55 AM | #2089 |
Lieutenant
113
Rep 513
Posts
Drives: 2008 335i
Join Date: Jan 2018
Location: Vancouver
|
Hey fellas, i did the 330 conversion successfully, but me car now throws a fault code which suggesting the DME has lost communication with my transmission.
Hass said I have to get my car software updated to a newer version as it is like 1.0 before applying the 330 flash again. To do this i need to flash back to stock and get that code out of my car or bmw won't touch it. Upon running the stock flash I'm getting the following errors MF_NAAB_DATEI= MF_PROGRAMM_DATEI= MF_DATEN_DATEI=MSV80_S8608331_328i.0da MF_DIAGNOSEPROTOKOLL= HW interface activted. PABD set. P-SGBD set. ECU-Address set. Data and/or program and/or NAAB file set. INFO000=Error: Error 212: Error on checking data consitency -> in data datafile (DAF) INFO001=Error: Error 2021: Error LFCDHDIA.CPP (12msv80.IPS/IPO) CDHapiResultText 1 Datatransmission to ECU disturbed IFH-0010: Datatransmission to controlunit disturbed 12MSV80 INFO002=Error: Error 2021: Error COAPI2.CPP coapiRunCabd 6 Datatransmission to ECU disturbed SG_AIF_LESEN INFO003=Error: Error 2021: Error COAPIKF.CPP coapiKfKonvertGetRef 1 Datatransmission to ECU disturbed Data will be programmed. INFO004=Error: Error 211: Error on flash programming! INFO005=Error: Error 2089: PABD 05MSV80 Programmieren 2544 switching programming mode failed 12MSV80, DIAGNOSE_MODE (ECUPM): ERROR_ECU_SECURITY_ACCESS_DENIED__SECURITY_ACCESS_ REQUESTED INFO006=Error: Error 2084: PABD 05MSV80 FlashSchreiben 1448 Flash download failed 12MSV80, FLASH_SCHREIBEN (...): IFH-0010: Datatransmission to controlunit disturbed INFO007=Error: Error 2084: PABD 05MSV80 Programmieren 3247 Flash download failed 12MSV80, FLASH_SCHREIBEN (...) INFO008=Error: Error 2084: Error COAPI2.CPP coapiRunCabd 6 Flash download failed SG_PROGRAMMIEREN INFO009=Error: Error 2084: Error COAPIKF.CPP coapiKfProgSgDevelop 4 Flash download failed ERG=Programming not ok. Fatal Error Batch mode ended Press any key to continue . . . I'm not sure what to do at this point. Cable, computer and car are all the same as when i did the 330 flash, but the stock flash is not happy. Last edited by Pinscher; 01-30-2019 at 04:12 PM.. |
Appreciate
0
|
Bookmarks |
|
|