[BimmerItaly]

Hi guys, can someone help me about flash.
I want to flash my TCU, but in origin it have ZBnumbers like 7573661 and not 7591971 like should be.
Is it possible to do?

THanks very much, and sorry for my bad english.

[toby_2028]

Originally Posted by 808AWD325xi

Several forum members have asked me about the Alpina D3 transmission flash. I finally had time to look into it and verify the firmware release. Others have shared limited information to date, but none have been as complete. Enjoy!

THIS INFORMATION IS PROVIDED “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL I BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS INFORMATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

ECU Family: GKE215
Assembly Number (ZB/ZUSB): 7603531
Release Date: 23.04.2009

Frequently Asked Questions

1. Which transmission is this firmware compatible with?

The ZF 6HP 6 Speed Automatic Transmission (6HP19TÜ or 6HP21)

2. Which vehicle(s) was this firmware qualified for?

• E92 320d
• E90 LCI 320d (09/08-12/11)
• E91 LCI 318d (09/08-02/10)
• E91 LCI 320d (03/10-05/12)
• E92 LCI 320d (03/10-05/13)

3. How can I verify that my transmission is compatible with this firmware?

Display the part numbers of all installed modules with INPA...E90 -> Select E90 -> Functional Jobs -> <F2> Identification. The part number of the EGS module should be 7591971.

Please share your experiences and feedback!

If you found this information useful, please click on the Appreciate button at the bottom of this post.

First of all: Thanks to all the forum members that have provided the information for my successful flash. All credit goes out to you.

I flashed my 2011 E90 LCI 184HK, but i failed at 11% and the gearbox was broken. Luckyle I was able to revert to the original firmware. (Guide provided)

Can anyone help me sort out this error, because i really want the Alpina software :-)

Failed at 10 - 12% with this error:

[21:51:38.674] [2018-05-16] [--] 1020 Error COAPIKF.CPP coapiKfInit 31
[21:51:38.674] [2018-05-16] [--] File could not be opened for reading info.eng

UPDATE: Fixed the problem - Installed all the BMW tools again using another guide, instead of Mikes easy BMWTools setup.
Working guide/video for BMW Tools setup: forum.e46fanatics.com/showthread.php?t=1126314 - This guide is valid..
NB: I Use Windows 10.


================================================== ==============================(19)

Here is the guide for reverting if flash fails or you just want to go back to stock :-)
DO THIS AT YOUR OWN RISK. I AM NOT RESPONSIBLE FOR ANY DAMAGE TO YOUR VEHICLE.

Going back to stock - Flash your transmission to the latest original software.
1: Once connected with WinKFP, Press (F1) comfort mode.
2: Press (F3) Update ZUSB and Choose ECU GKE215. (The newest software will automatically be selected)
3: Press (F4) VIN and Enter VIN (Important – Double-check that VIN number is correct) --> Click OK.
4: Press DONE (F8)
5: Press (F3) Program.
6: A pop-up window will now say you can code the ECU 63 more times. --> Click OK

Flashing begins and you will have to wait till it reaches 100% twice.
The first bar will finish rather quickly and then another bar progress of 100% will take about 3-4 minutes
the most and it will be completed.

7: If everything is done correctly, then you will get a pop up screen saying programming done. --> Click OK
8: Shut off car by taking the key out. Lock car with key and wait 5 minutes (Wait for the car to enter sleep mode) and then start the car.
9: Read and clear error code if any.

BTW I made this guide for flashing transmission. Mine failed at 11%, but I think the guide i OK. Maybe someone in here can confirm that it is OK?
The guide is made from div. threads from Bimmerpost.com.

UPDATE: Fixed the problem - Installed all the BMW tools again using another guide, instead of Mikes easy BMWTools setup.
Working guide/video for BMW Tools setup: forum.e46fanatics.com/showthread.php?t=1126314 - This guide is valid..

DO THIS AT YOUR OWN RISK. I AM NOT RESPONSIBLE FOR ANY DAMAGE TO YOUR VEHICLE.

Alpina transmission flash on E9x 320D

Firmware compatible with:
The ZF 6HP 6 Speed Automatic Transmission (6HP19TÜ or 6HP21)

E92 320d
E90 LCI 320d (09/08-12/11)
E91 LCI 318d (09/08-02/10)
E91 LCI 320d (03/10-05/12)
E92 LCI 320d (03/10-05/13)

Check compatibility:
Display the part numbers of all installed modules with INPA:
Select E90 -> Functional Jobs
Press <F2> Identification.
The part number of the EGS module should be 7591971.

The Alpina firmware:
ECU Family: GKE215
Assembly Number (ZB/ZUSB): 7603531
Release Date: 23.04.2009

Setup WinKFP:
1: Open INPA and verify that it is connected properly
2: Close INPA and open WinKFP --> Configuation --> Setup and save INI options like this: (See picture)

Before flashing:
Important:
1: For those using Procede or JB4 make sure the tune is set to VALET map 0 before you start the flash.
2: Make sure your battery is good if not get a battery charger.
3: For newer build cars after the flash the paddle shifters no longer works. If this is the case you would follow part II of this DIY.

Flashing the Gearbox ECU:
1: Open driver’s door and turn ignition ON.
2: Connect cable to ODB connector.
3: Load WinKFP software.
4: Once connected with WinKFP, Press (F1) comfort mode.
5: Press (F3) Update ZUSB and Choose ECU GKE215.
6: Press (F2) Choose ZUSB.
7: Choose ECU GKE215 and next to it there will be ZB-Numbers - Find 7603531 and click OK.

If you have done it correctly, so far you will see, at the top Assembly Identification number 7603531 and it will automatically reference 7591971

8: Press (F4) VIN and Enter VIN (Important – Double-check that VIN number is correct) --> Click OK.
9: Press DONE (F8)
10: Press (F3) Program.
11: A pop-up window will now say you can code the ECU 63 more times. --> Click OK

Flashing begins and you will have to wait till it reaches 100% twice.
The first bar will finish rather quickly and then another bar progress of 100% will take about 3-4 minutes
the most and it will be completed.

12: If everything is done correctly, then you will get a pop up screen saying programming done. --> Click OK
13: Shut off car by taking the key out. Lock car with key and wait 5 minutes (Wait for the car to enter sleep mode) and then start the car.
14: Read and clear error code if any.

[ivanp]

Hello,

Is this flash supposed to work on X3 E83 / 2010 N47D20, 6HP19 and EGS BMW part number 7591971?
Current software version is 7593314

Thank you,
Paul

[sinan33]

Hi,
I can't find flash file for 7603531.
I downloaded some spflash packages but none of them includes 7603531.
Could some one provide me a download link for it?
Regards...

[toby_2028]

Originally Posted by sinan33

Hi,
I can't find flash file for 7603531.
I downloaded some spflash packages but none of them includes 7603531.
Could some one provide me a download link for it?
Regards...

Hi
You need SPDATEN for WinKFP.
You can download v60.1 from Bimmergeeks download page.
https://www.bimmergeeks.net/downloads

[sinan33]

Originally Posted by toby_2028

Hi
You need SPDATEN for WinKFP.
You can download v60.1 from Bimmergeeks download page.
https://www.bimmergeeks.net/downloads

Thnak you for your reply; i have downloaded several spflash files but none of them is includes this flash,anyways i will download and check this package too.

[toby_2028]

Originally Posted by sinan33

Thnak you for your reply; i have downloaded several spflash files but none of them is includes this flash,anyways i will download and check this package too.

I used SPDATEN 53.something. Newer versions should include the same, but I cant be sure.

Remember, if you change the software, be sure to reset adaptions and do the basic burnin exacly as described. Here is a guide. https://bmw.***********.com/attachme...ions-pdf.2851/

The Alpina is the software i perfer over the xHP, but only if you have a remap that pulls until 4500 or more. If you dont have a remap, the gears will change to late. No remap, go with xHP stage 1 or 2.

I have tryed all the software and my recumentdations are build on fast shift with comfort in mind.

If you just want the fastest shift, go xHP stage 3.

[MCCoding]

Anyone done this on a M57 335d?

EGR DPF and swirlflaps with upgraded intercooler. What is recommended? idealy a DIY as all the equipment and software is available

[lnxguy]

Originally Posted by MCCoding

Anyone done this on a M57 335d?

EGR DPF and swirlflaps with upgraded intercooler. What is recommended? idealy a DIY as all the equipment and software is available

Completely different transmission. Just get a Sutphin tune and be done with it.