E90Post
 


 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > DIY Guides > DIY M3/OEM Upper & Lower Control Arms



Reply
 
Thread Tools Search this Thread
      11-08-2020, 06:08 PM   #133
Azntincan
New Member
2
Rep
5
Posts

Drives: BMW e93 2010, MB GLE 2020
Join Date: Sep 2020
Location: New York

iTrader: (0)

Just changed the front control arms to m3 OEM parts. The rear control arm(wishbone) was a B**** to put back into the subframe. We used a extension rod to expand the subframe a few mm. Then used a back end of rubber mallet and hammered it in to the space. Once we were able to get the bushing and the subframe slightly aligned, we placed a nail punch through one side and hammered it until it aligned on the other side. Now it was perfect for the bolt.
FYI, displacing the alignment, made it easier to remove and but back the bolt.
Appreciate 1
      04-15-2021, 07:56 AM   #134
Dovydas.B
Private
9
Rep
56
Posts

Drives: E92 335i LCI
Join Date: Nov 2018
Location: Lithuania

iTrader: (0)

Guys, how did you managed to torque the wishbone and tension strut to the wheel bearing with T40 to 175 NM??? Because I don't see how can I use socket with torque wrench when there is a need to hold that the inner thing with T40.

Doing the m3 arms (front/rear) tomorrow.
Appreciate 1
mantis276.00
      04-15-2021, 10:05 AM   #135
mantis
Captain
mantis's Avatar
United_States
276
Rep
655
Posts

Drives: 2011 328i
Join Date: May 2016
Location: socal

iTrader: (0)

Garage List
2011 e90  [5.50]
Quote:
Originally Posted by Azntincan View Post
Just changed the front control arms to m3 OEM parts. The rear control arm(wishbone) was a B**** to put back into the subframe. We used a extension rod to expand the subframe a few mm. Then used a back end of rubber mallet and hammered it in to the space. Once we were able to get the bushing and the subframe slightly aligned, we placed a nail punch through one side and hammered it until it aligned on the other side. Now it was perfect for the bolt.
FYI, displacing the alignment, made it easier to remove and but back the bolt.
its my understanding that all the M3 control arm bushing spacers(metal) are in need of being ground down a few thousandths to fit in the non M3 subframes
Appreciate 0
      06-25-2021, 04:31 AM   #136
jamesfawcett
Second Lieutenant
jamesfawcett's Avatar
49
Rep
210
Posts

Drives: 335D E91
Join Date: Nov 2016
Location: West Yorkshire

iTrader: (0)

Sorry to dig up an old thread, but I can see it's already been dug up before

Anyone got the part number for the headlight level regulating rod, is it 37142283867 ?

Thanks
James
Appreciate 0
      12-21-2021, 10:07 AM   #137
CreativeS
Registered
CreativeS's Avatar
Netherlands
2
Rep
2
Posts

Drives: E90 325iA & E46/5 318tiA M
Join Date: Jan 2019
Location: Achterhoek

iTrader: (0)

Quote:
Originally Posted by jamesfawcett View Post
Sorry to dig up an old thread, but I can see it's already been dug up before

Anyone got the part number for the headlight level regulating rod, is it 37142283867 ?
6 month's later, but... yes!
And you need 2x 07129905817.

End of january they're going to do the upgrade on my E90 325i.
Appreciate 1
      01-06-2022, 02:55 PM   #138
Richard Feynman
New Member
Richard Feynman's Avatar
3
Rep
6
Posts

Drives: E90.325i.6MT, F22.M235i.6MT
Join Date: Jan 2022
Location: San Diego

iTrader: (0)

Thank you!
Appreciate 0
      03-09-2022, 09:58 PM   #139
StradaRedlands
Colonel
StradaRedlands's Avatar
United_States
4759
Rep
2,873
Posts

Drives: 2006 BMW 330i MT
Join Date: Dec 2021
Location: SoCal

iTrader: (2)

Garage List
2006 BMW 330i  [8.21]
2009 BMW 328i Touri ...  [7.90]
2013 BMW X5 35i  [7.63]
2011 BMW 528i  [8.75]
2006 Mazda3  [5.50]
Well, I hoped to get it all done today, but that stupid wishbone threw my plans sideways. I'll take a little off it tomorrow, and hope I didn't gouge the subframe too much trying to force it in there. Front/torsion went in fine. I figured I'd be in and out in less than an hour. But still on the passenger side at this point. Dremel to the rescue tomorrow! Used hand tools and everything came off fine. One nut was really stiff and I had to really lean into it, the T40 bit holding the bolt never snapped!

Last edited by StradaRedlands; 03-09-2022 at 10:28 PM..
Appreciate 0
      03-29-2022, 11:26 AM   #140
R3dLeader
Second Lieutenant
United_States
152
Rep
209
Posts

Drives: e92 and e93 335i
Join Date: Feb 2021
Location: West Coast

iTrader: (0)

Is there a rough estimate for setting the toe to an acceptable value after the M3 arm install? I read 3.5 turns of the tie rod to toe out after the install will get you close. I think this came from the 1 series forums.

I plan to get a proper alignment later, but I think it should be possible to correct the toe approximately for now. At least so I can drive to the alignment rack lol.

Worst case, I could break out the strings and try to measure toe.
Worst worst case: my tie rods will be frozen

EDIT/UPDATE: Control arm install went smoothly except for the fact that the left thrust arm FCP sent me appeared to be a counterfeit from Malaysia. The aluminium had a totally different luster to it indicating different manufacturing process, the nut did not have the nylon lock, and other differences. It was pretty rough.

I had to order the left arm from Eeuroparts and it arrived as the genuine German TRW arm. I have pictures to compare the 2 if anyone is interested. The other 3 arms from FCP were genuine. Of course I contacted them and they are returning it and had discovered the problem on their own the day prior. They didn't inform their customers who purchased this kit....

Adjusted the left tie rod 3 turns as this should get the toe close. No issues with the tie rod. Tried to adjust the right tie rod and of course it was seized! The final step of my install.

New tie rods arrived yesterday and will complete that over the next few days. Will get a shop to check the toe but I'm curious how close my 3 turns (plus tie rod replacement) will get me. Stay tuned.

Last edited by R3dLeader; 04-08-2022 at 11:58 AM.. Reason: Update info
Appreciate 0
      11-29-2022, 02:24 PM   #141
jurek_purek
New Member
0
Rep
25
Posts

Drives: F30 325d
Join Date: May 2021
Location: DE

iTrader: (0)

hey
do you have some part no. for this parts?

thanks
Appreciate 0
      08-26-2023, 03:14 AM   #142
kolopn
Enlisted Member
23
Rep
40
Posts

Drives: E92 325i N52B25
Join Date: May 2023
Location: Poland

iTrader: (0)

Just for buying info - Tension struts (big one arms) are being made in Malaysia - Ball joints now are made of chocolate, and going to fail very quick (In my experience after mounting new ones, ball joints starting to knock after 2-3 months of daily use).
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 03:06 PM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST