|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
Coding auto to manual 335d E92 euro
|
|
02-25-2019, 09:03 AM | #1 |
New Member
1
Rep 21
Posts |
Coding auto to manual 335d E92 euro
Hi
I started converting my 335d auto to manual a month ago. Thanks to Grazy_87 and RSDAVE for leading the way. The mechanical part is almost finished, it my remains changed the clutch receiver, replaced by a new one. The wiring is done too, here are the pins for those interested by him: Clutch switch >>> Calculators / mass 1 >>> Mass point 2 >>> DDE (pin50 X2412) 3 >>> CAS (pin3 X13376) 4 >>> CAS (pin41 X13376) Reverse switch >>> Calculator / mass 1 >>> FRM (pin19 x14261) 2 >>> Mass point After that I reconnect the battery, wait 30 minutes then get into the car with the pc .. But before coded, I wanted to see if it really does not start without coding. So I put the key and press the clutch to start. And miraculously, she starts. With some flaws (BVA down, starter system on the side, the fan has bottom ..) but it starts. Then to avoid having all these errors, I did the coding. Since I'm not the procedure for 335d, I used the one I found for 335i. So I removed the FA S205 from CAS and NFRM. Then coded CAS / FRM / KOMBI / DSC / DDE. Now I'm no longer defaults on the CCC screen but I still have the fan running and errors on the CAS, DDE, and KOMBI who are still looking for the EGS calculator. I tried to put the FA S207 (6 speed manual gearbox) but it does not take it. |
02-25-2019, 11:12 AM | #2 | |
Colonel
527
Rep 2,505
Posts |
Quote:
This has been discussed a lot recently here. There are some options which are 'learnt' and cannot be coded with NCS Expert. You need to clear adaptions in the DDE. Including the learned values. You can do this with INPA or tool32 look for varianten_loschen and adaptions_loschen in the engine prg for example. Or in INPA look for 'gelernte Varianten' |
|
Appreciate
0
|
02-25-2019, 12:29 PM | #3 |
New Member
1
Rep 21
Posts |
Thank you for your help.
The fault codes are for the DDE 4BE3 botschaft (GEARBX_DATA, 0xBA) 4BE8 botschaft (GEARBX_DATA2, 0x1A2) 4DF3 botschaft (TORQUE_GEARBX, 0xB5) for CAS 0xA0B1 SG_Eingang_P_N for the KOMBI 0xA560 ID_Ausfall Anzeige Schalthinweis I can not find 'gelernte Varianten' in INPA, there is adaptions_loschen but it does not work. I will watch with Tool32. I keep you informed of the result. |
Appreciate
0
|
03-03-2019, 07:27 AM | #4 |
New Member
1
Rep 21
Posts |
There is no "varianten_loschen" and "adaptions_loschen" in INPA.
With TOOL32, there is "adaptions_loschen" but it does not work. My vehicle is terminating mechanically. She starts and drive it perfectly. No safe mode, all the power on each shift. The problems are the fan running too fast, the speed regulator does not work and it only starts when the second presses the start button. With INPA, I saw that the clutch switch is not seen by the DDE. Does the DDE version support the clutch switch? Can be a flash with winkpf, but with which version of program? |
Appreciate
0
|
04-16-2019, 06:51 PM | #5 |
New Member
1
Rep 21
Posts |
Hi everybody.
I come to inform you of the resolution of my problems. the cruise control works perfectly, the fan runs normally and I no longer press 2x to start. everything has been adjusted by modifying the engine map. the work was done by a French tuner. |
Appreciate
0
|
09-23-2019, 09:43 AM | #8 |
SleepEatRunRepeat
2
Rep 26
Posts |
Great looking car, too!
Would love to convert my '11 335d to a manual transmission and have all that torque fully available at my discretion. Enjoy the new machine! May the torque be with you! Last edited by dkpete101; 09-23-2019 at 09:54 AM.. |
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|