Replaced DDE/No Cruise

M3T · 09-26-2020, 02:47 PM

Hi,
Replaced DDE, sent away to be matched to existing key and CAS, car operates fully except for cruise control. Understand Cruise and DSC is shared module? Company who matched DDE to CAS did not want to install my VIN to DDE after tow failed attempts previously.

Can I re-calibrate DSC to fix Cruise ( I have DIS/GT1 INPA etc)?

MANY Thanks in advance.

F31B48 · 09-28-2020, 12:52 AM

Quote:

Originally Posted by M3T

Hi,
Replaced DDE, sent away to be matched to existing key and CAS, car operates fully except for cruise control. Understand Cruise and DSC is shared module? Company who matched DDE to CAS did not want to install my VIN to DDE after tow failed attempts previously.

Can I re-calibrate DSC to fix Cruise ( I have DIS/GT1 INPA etc)?

MANY Thanks in advance.

The DSC doesn't appear on the wiring diagram for cruise control, but i would say it would communicate with it via the pt-can. It does go directly through the junction box though so quite possibly a VIN mismatch issue. Are there any fault codes? Is your engine m57 or n57?

https://www.newtis.info/tisv2/a/en/e...ontrol/pbURy4t

CarAbuser · 09-28-2020, 04:11 AM

Probably a coding issue with the DME, cruise has a enable toggle within the DME that is set during flash. You could try flashing using WinKFP, that should pick up your correct VO and write accordingly.

M3T · 09-29-2020, 10:24 AM

Thanks both for the replies.

It is an M57 TU2 engine.

I had a loose security wheel bolt on shake down and now have a wheel torque error code that will not clear. I thought perhaps it and the cruise control error were related and could be fixed with a re-calibration of the DSC?

Just thought I would ask before I break it trying the re-flash.

Many Thanks.

09-26-2020, 02:47 PM	#1
M3T New Member 0 Rep 6 Posts Drives: BMW E91 330D Join Date: Feb 2020 Location: UK iTrader: (0)	Replaced DDE/No Cruise Hi, Replaced DDE, sent away to be matched to existing key and CAS, car operates fully except for cruise control. Understand Cruise and DSC is shared module? Company who matched DDE to CAS did not want to install my VIN to DDE after tow failed attempts previously. Can I re-calibrate DSC to fix Cruise ( I have DIS/GT1 INPA etc)? MANY Thanks in advance. Last edited by M3T; 09-26-2020 at 03:00 PM..
	Appreciate 0 Tweet Quote

09-28-2020, 04:11 AM	#3
CarAbuser Lieutenant Colonel 469 Rep 1,536 Posts Drives: Z4 35i DCT / E92 335i DCT Join Date: Jul 2010 Location: United Kingdom iTrader: (0)	Probably a coding issue with the DME, cruise has a enable toggle within the DME that is set during flash. You could try flashing using WinKFP, that should pick up your correct VO and write accordingly.
	Appreciate 0 Quote

09-29-2020, 10:24 AM	#4
M3T New Member 0 Rep 6 Posts Drives: BMW E91 330D Join Date: Feb 2020 Location: UK iTrader: (0)	Thanks both for the replies. It is an M57 TU2 engine. I had a loose security wheel bolt on shake down and now have a wheel torque error code that will not clear. I thought perhaps it and the cruise control error were related and could be fixed with a re-calibration of the DSC? Just thought I would ask before I break it trying the re-flash. Many Thanks.
	Appreciate 0 Quote