[ferocity02]

Just got my K+DCAN cable in the mail today and would like to know what program(s) I should download and install. I would like to perform coding, read/erase fault codes, and perform the Alpina trans flash. Links to the software download would be helpful too, as it's pretty hard to find working links these days.

Thanks!

[Sensible_]

Sounds like you need BMW Standard Tools:

Diagnostics - INPA
Coding - NCS-Expert
Software flash - Winkfp

Easiest way to install is by using the coding pack:

http://dfiles.eu/files/o0cro356a

Instructions inside. Depending what i-level your car is it you may need to update the sp-daten. (use BMW coding tool included in pack)

[ferocity02]

Thank you! I'll download them and see what trouble I can get into.

[ferocity02]

Originally Posted by Sensible_

Sounds like you need BMW Standard Tools:

Diagnostics - INPA
Coding - NCS-Expert
Software flash - Winkfp

Easiest way to install is by using the coding pack:

http://dfiles.eu/files/o0cro356a

Instructions inside. Depending what i-level your car is it you may need to update the sp-daten. (use BMW coding tool included in pack)

I downloaded it the file from that link.

So I tried unzipping it with windows 7 and it gave me an error, and then with 7-zip and all of the files have no size, ie 0 bytes. What's the trick here?

[Sensible_]

its password protected. I've pm'd you the password.

[NW 335i]

Is this what I need? In addition to the BMW standard tools linked earlier? Sorry I am a little new to all of this. A bit of information overload right now.
http://www.ebay.com/itm/For-BMW-INPA...ht_3109wt_1178

Thank you

[Isetta]

You will be able to read/erase fault codes with that K+DCAN cable.
You can also use Rheingold BMW diagnostic software for reading/erasing fault memory and testing components which is very easy to use.

[ferocity02]

I got the software installed and the programs all open up, but haven't gotten around to actually using them or connecting to the vehicle.

[NW 335i]

Originally Posted by Isetta

You will be able to read/erase fault codes with that K+DCAN cable.
You can also use Rheingold BMW diagnostic software for reading/erasing fault memory and testing components which is very easy to use.

Will I be able to code and flash with that cable? In addition to using INPA?
What is this Rheingold diagnostic software?

I suspect I may have an injector going and want to replace them and recode them and reset adaptations.

If the cable I linked above is incorrect can you link me to one I should buy?
Thank you!

[cryptomit]

A cable you linked is fine, buy it and it will work with your car and Rheingold, and INPA.

[force_feed]

Will this software work on windows xp?

Can I get the password??

[ferocity02]

Originally Posted by Sensible_

Sounds like you need BMW Standard Tools:

Diagnostics - INPA
Coding - NCS-Expert
Software flash - Winkfp

Easiest way to install is by using the coding pack:

http://dfiles.eu/files/o0cro356a

Instructions inside. Depending what i-level your car is it you may need to update the sp-daten. (use BMW coding tool included in pack)

Does this pack come with the latest SP-daten that I need? It says it comes with V49 for E8X, will that work for me? Mine is an 2007 E90.

I'm having a slough of errors when trying to connect to the car with INPA.

[Sensible_]

No, its not latest daten. However you can update it easily.

Also, you may need EXX.ipo

Just Google it and download.

[ferocity02]

Originally Posted by Sensible_

No, its not latest daten. However you can update it easily.

Also, you may need EXX.ipo

Just Google it and download.

I did get the EXX.ipo error, found the file online, and put it into the correct folder. But I get another error, forgot what it said exactly.

I'm beginning to think my 04/2007 has the older protocol.

[TwinTurboRacer]

Originally Posted by ferocity02

I did get the EXX.ipo error, found the file online, and put it into the correct folder. But I get another error, forgot what it said exactly.

I'm beginning to think my 04/2007 has the older protocol.

Likely the other way around and that's why the cheaper cable doesn't work. the cheap cable seem to always work for pre-03/2007 models. Post 3/07 is hit or miss... I'm trying to find something cheaper than the one-stop version myself. I found this one, but wanted someone else who had experience with it to chime in before I bought it... It'll be good for the F-series as well and comes with some software to save some time.

http://www.ebay.com/itm/321344738425...%3AMEBIDX%3AIT

[IN54NITY]

PM the zip password oh pretty please, Sensible? Thank you in advance.

The links in the sticky thread are obsolete/unavailable.

[Sensible_]

it's not a secret, i jst forgot to post it:

password:

bmw*coding*pack052013

(Remove stars)

[ferocity02]

Hooray! I was able to connect to my car using the download and guide here: http://www.e90post.com/forums/showthread.php?t=645844

I only spent a couple minutes in INPA but took some screenshots from the "Functional Jobs" menu. Can someone take a look and let me know if you see any strange? I noticed there is an E104 fault in the KOMBI, is this something to worry about?

Since I'm using a K+DCAN cable, does this mean my car has the newer 04/2007+ protocol?

[paprmkr]

anyone has like a writeup on how to start the procedure once all software is installed?

[Sensible_]

E104:
CAN low error
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

I believe is reference to rain/light sensor.

Clear it and see if it returns. Are you auto wipers / lights working correctly? (if fitted?)

[ferocity02]

Originally Posted by Sensible_

E104:
CAN low error
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

I believe is reference to rain/light sensor.

Clear it and see if it returns. Are you auto wipers / lights working correctly? (if fitted?)

Yes, auto wipers are working.

Where did you find that information?

[ferocity02]

Sensible,

When installing the BMW coding pack, do I need to follow the steps in this PDF to amend the "Path" variable and add the "ediabas_config_dir" variable in the Environment Variables window? There was nothing in the coding pack about this, but it seems like it might be important.