|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Xtrons headunit - rubbish DAB! What to do?
|
|
07-12-2018, 10:43 AM | #45 |
Private
12
Rep 65
Posts |
So, unamplified splitter works....... but not brilliantly. In the meantime, I stuck my windscreen one on, just so I had something. It's actually not bad for me!!
Onto the next and final option though Might as well be conscientious. |
Appreciate
0
|
07-13-2018, 06:55 AM | #46 |
Lieutenant
69
Rep 466
Posts |
What was that again? The OEM DAB Antenna??
|
Appreciate
0
|
07-16-2018, 05:59 AM | #47 |
Private
12
Rep 65
Posts |
|
Appreciate
0
|
07-16-2018, 06:54 AM | #48 |
Lieutenant
69
Rep 466
Posts |
|
Appreciate
0
|
08-23-2018, 10:45 AM | #49 |
Private
12
Rep 65
Posts |
blueh88
It's taken long enough..... but I have some answers...... Yes, you can tap the factory antenna, and yes, it works...... and yes, you can modify a crappy £10 diversity module from eBay, to work. I didn't buy a DAB diversity module in the end, however I finally got chance to dismantle the one I bought for a tenner on eBay. Pretty much all of the gubbings for the DAB appear to be already there and according to the BMW dealer I spoke too, the same rear glass was used on every BMW E90, including those with and without DAB. So, all you really need to do is just solder a proper connector on: https://www.ebay.co.uk/itm/UK-Seller...8AAOSwjDZYlOuZ Instead of waiting around, I had an old universal 5cm fakra to fakra connector that wasn't much use to me anymore. I cut one end off and soldered the live wire to the centre pad and the earth to one of the 4 surrounding pads. This was just for testing. Very sorry to those who like good soldering. I like good soldering too, but I was using my brand new iron and it came with a pack of 100% lead-free solder. Have any of you ever used it? Don't. It's awful. It doesn't flow at all. You can use as much flux as you want, it just doesn't flow at all. It goes into big lumps like that. Terrible stuff. Throw it in the bin and buy some nice lead solder. I didn't have a long enough cable to test with the USB dongle in the front, so I grabbed an old Kenwood DAB radio that was in my Mazda, hooked it up to a car battery charger used that. Voila, it works...... So, having come this far, I felt it was worth a punt..... Grabbed one of these: https://www.ebay.co.uk/itm/5M-Metre-...IAAOSwICZbc~6S and https://www.ebay.co.uk/itm/CEN-SMA-M...AAAOSwSUdbbq7q (There's a very good reason I didn't buy a 5M Fakra to SMA) Now unfortunately, I've lost all my photos from here out, but from memory.... Obviously solder the new fakra PCB connector onto the board. I would buy a yellow one, it's more OEM then. You'll need to modifying the plastic casing as it's all blocked off. I just took a dremel to it. Took about 5 minutes to lob off enough to get the case back on and tbh, you'd think it was OEM from the outside if you're careful(ish). It's held to the car by the two black torx in the middle. Remove the old one carefully. The ribbon cable to the rear cluster is very thin. Screw your new one in. It might be a good time to connect the power connector as it can be a pain to get back in when on the car. Now, wire routing. I couldn't route the cable through the roof. Everytime I tried, using a coat hanger or something similar, I eventually hit something. I didn't even get very far along tbh, at least I don't think I did. Your best option without removing the whole roof lining, is to run the wire to the left or right and down the C-pillar, then run it like a normal cable along the floor. I had already run the cabling for the reversing camera down the right hand side, so I decided to go to the left. It's easy. You don't even need a coat hanger, just lever the roof lining at the back slightly with your finger and run the wire along, boom, it'll run straight down the C-pillar. Make sure it is not interfering with the airbag, can't really stress that enough. Once you've run it down there, you can angle the rear seat cushion forward, run it down the side so it's properly obscured to the floor where the other OEM wiring is and then route it under the 'scuttle panels'(? Not sure what you call them) that run along the floor. All very simple. Took about 20-30 minutes at most. Once you're at the front, there's some trim you have to drop down under the fuse box. I had already done that once before to put the yellow live wire in, so no issue there. Run it up behind the head unit and boom, put in the converter to SMA which is what all those USB dongles work. There's a fairly generous amount of slack unsurprisingly, so I bunched it up under the fuse box. There's a few places you can cable tie it too. Leave a bit so the wire is nice and floppy and not straining. I notice the OEM antenna is very short. You could try a 3m cable, but I'm not sure if it would be long enough. Probably, but better being safe than sorry and the 5m cable was only a pound more anyway!! Connect it to the head unit. Cross your fingers and hope it works. Boom.... it does. The signal is pretty solid. 7.5/10 I would say. I've driven with it like this for a few weeks though and I don't think I'll be going back to the windscreen antenna as it's definitely improved and it's much more seamless. I will probably leave the windscreen antenna just in case, but if I was to do it on another E90, I wouldn't bother with the windscreen one. I will be honest and say now that it's not as good as my sisters F30 reception wise. There are maybe one or two consistent dead spots on my drive to work where you get that nasty distortion and drop outs (for a second or two) and my sisters doesn't seem to do it as much or at all, but there's potentially a few reasons for that: 1. The DAB interface is a cheap generic piece of kit from China, that wasn't even designed for cars, not a heavily tested and abused piece of kit designed by a big car manufacturer. It's possible that there are edge cases in signal distortion that it can't handle. 2. Although DAB is now considered a fairly mature technology, my E90 was registered September 1st 2006, so it's hardly new. I also suspect still has the original rear windscreen. DAB was a reasonably new technology in 2006, and DAB+ didn't even exist back then! Most car manufacturers didn't adopt DAB technology until DAB+ because the original DAB was so ropey. It's fair to say BMW were working with a fairly limited set of parameters. I suspect they've worked on fine tuning the antenna itself that is built within the windscreen and it is much better. I think they can be forgiven though. Also, age will have no doubt played a part. The metal elements degrade with time, they certainly did on my VW. 3. I've missed something on the diversity module or made a mistake in my install. Although it works, it's entirely possible there's a component I missed on the diversity module or something. The 5m wire is too long? Etc etc etc. Anyway, I would still say it's a success and wouldn't hesitate to recommend this as a cheap OEM way to take advantage of DAB Took a while, but we got there Last edited by BeamerNub; 08-23-2018 at 10:55 AM.. |
Appreciate
1
blueh8869.00 |
08-24-2018, 09:43 AM | #50 | |
Lieutenant
69
Rep 466
Posts |
Quote:
So to summarize: 1. Take out the PCB 2. Solder the Fakra connector onto the board 3. Run th 5m cable from the rear windscreen to the front 4. Connect to the DAB dongle with the converter thing (which thankfully I already have!) 5. Job Done. ? |
|
Appreciate
0
|
08-28-2018, 04:08 AM | #51 | |
Private
12
Rep 65
Posts |
Quote:
|
|
Appreciate
1
blueh8869.00 |
12-20-2018, 07:23 AM | #52 |
Lieutenant
69
Rep 466
Posts |
Just a little update - I've installed the Fakra 5M extension from the back of the stereo (the USB DAB dongle) and run it down the side of the car to the rear. Just waiting for the yellow Fakra plug thingy to be delivered and will solder onto the Diversity board..
One thing I haven't checked is if my Diversity module actually has the space there to solder this piece on! Oh well..I will know soon enough once I get round to taking it out. |
Appreciate
0
|
01-07-2019, 04:26 PM | #53 |
Lieutenant
69
Rep 466
Posts |
okay so just got round to doing this and....no luck. damnit. Done exactly as per instructions and no channels found whatsoever. Not sure what went wrong. It may just be my area??? Will see how it is on my way to work tomorrow.
At least now I have a nice long aerial wire from back of head unit to the diversity so possibly could try some aftermarket shark fins in place of current fin...
__________________
Cosmetics: 18" Axes CS Lite Wheels in Shadow Chrome, Custom Headlights (KYCS)
Mechanical: Hybrid Turbo, Wagner Intercooler, Ecotune Sports Downpipe, Ecotune calibration (350bhp/745Nm), xHP Stage 3, Bilstein B12, M3 front control arms, Quaife LSD Audio/Visual: Xtrons 9" Android headunit, Match 8" underseat subs, Vibe 4" door components, Pioneer 4 channel amp, reverse camera |
Appreciate
0
|
04-01-2019, 05:46 AM | #54 |
Lieutenant
69
Rep 466
Posts |
Just to resurrect this, I think it could be the DAB USB dongle (Xtrons) at fault. I plan to change this next to see if this helps. If so, winner. If not, then I will look into a better aerial..
|
Appreciate
0
|
Bookmarks |
|
|