|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Vin Is Faulty coapi2020 ifh0009
|
|
04-23-2012, 01:47 AM | #1 |
Enlisted Member
14
Rep 42
Posts |
Vin Is Faulty coapi2020 ifh0009
i have
a 06/08 build e92 ediabas 7.2 ncsexpert 3.1 E89 V46.2 daten files (ECU,SGDAT, DATEN) clear K+Dcan cable wit pin 8 removed completely cable latency is set to 1 and also set to com 1 Ediabas.ini file's remote host was changed to 192.168.68.1 and port to 6801 all things are set to OBD key on position but engine off i do have a JB4 tune but i even turned it off i just finished coding my friends 07 e90 with no problems, and when i try to code my 08 e92, i have error while trying to get the vin/chassis/ecu on NCSexpert... Its telling me vin is faulty, coapi-2020, ifh-0009 this is my error log ERROR! Modul: LFCDHDIA.CPP (A_E65CAS.IPS/IPO), Proc: CDHapiResultText, LineNr: 01, ErrorNr: 2020 COAPI-2020: no answer from ECU IFH-0009: ECU not connected or doesn't answer >> ERROR! Modul: COAPI2.CPP, Proc: coapiRunCabd, LineNr: 06, ErrorNr: 2020 FGNR_LESEN >> ERROR! Modul: COAPI.CPP, Proc: coapiReadFgNr, LineNr: 04, ErrorNr: 2020 FGNR_LESEN: A_E65CAS can someone help me figure out what can be wrong? TIA i already searched on everyforum i can and on google but still no luck... Last edited by guwakjai010; 10-05-2012 at 10:59 PM.. |
04-23-2012, 06:12 AM | #2 |
Banned
37
Rep 412
Posts |
Thereis no v46.2 there is v46.1 daten you sure you do everything proper cause it should work like a charm with this set. Key is in fob? Ignition on ? There are several combinations for differnet cars, one car is reading superb without key or igniotion second need both
|
Appreciate
0
|
04-23-2012, 08:56 AM | #3 |
Enlisted Member
14
Rep 42
Posts |
it says v46.2 on the folder, i don't know how else to verify it... i compared the amount of files in the folders with v42 and v38 daten files and it seems to have either the same amount of files or more than the older daten files... i have the key fb in wit ignition on... like i said, the funny part is i just coded my friends car an hour prior to trying it on mine...
|
Appreciate
0
|
04-23-2012, 09:29 AM | #4 |
Enlisted Member
14
Rep 42
Posts |
i think i might kno why... i'm looking at my OBD connector from the car and i don't see any metal connectors inside where pin 7 would go... im going to have to pulled that part out and inspect it...
|
Appreciate
0
|
04-24-2012, 09:09 AM | #8 |
Second Lieutenant
13
Rep 221
Posts |
|
Appreciate
0
|
04-24-2012, 08:56 PM | #12 |
441
Rep 18,331
Posts |
What month was your friend 2007 built should be the question? Is it before march of 2007?? The second question is why did you set the ediabas port to 6802 when it suppose to be set to 6801??
Last edited by cn555ic; 04-24-2012 at 09:17 PM.. |
Appreciate
0
|
04-25-2012, 12:21 AM | #13 |
Enlisted Member
14
Rep 42
Posts |
i gotta find his month.... but looking back at it, it is on port 6801 sorry bout that.... its set for OBD.... i looked at my dlc connector, PIN 7 is not there on the car... and also compared to my friend's car i have 6 pins in the connector while he has 7... and there were couple pins that werent in the same place...
|
Appreciate
0
|
07-30-2012, 05:06 PM | #15 |
Private
15
Rep 78
Posts |
vin is faulty
i received VIN is faulty code also. when my usb cable was not plugged in well, must be communications issue. obd setup should be run, inpa test should be good, driver should be updated. latency set to u, com port should be 1. in short, just things to keep in mind
|
Appreciate
0
|
10-05-2012, 09:13 PM | #18 | |
Enlisted Member
14
Rep 42
Posts |
Quote:
I originally took out pin 8 for the OLD cable was that i wasa afriad there were traces between 7and8 that i couldn't see... just to eliminate if it was soldered or internally traced together..... I bought a newer cable that supports past the march 2008 build date and can do up to 2011 i believe... and that cable worked on my 08 and 07... haven't used it on anything else tho... Hope this helps... |
|
Appreciate
0
|
10-05-2012, 09:15 PM | #19 | |
Enlisted Member
14
Rep 42
Posts |
Quote:
|
|
Appreciate
0
|
11-22-2012, 11:53 AM | #20 |
Banned
16
Rep 96
Posts |
hi guys i got a similar issue as you did
i have a bmw E60 530d which is 2005 model i can connect and code to this car fine i recenty brought a e93 convertible 2007 model its first registered in 6/07 i opened my cable and have disconnected pin 7-8 still in inpa it says no response from ecu from i try to read function jobs my inpa works on my other cars what could be wrong? do i have to change any ediabas settings? |
Appreciate
0
|
11-28-2012, 10:11 PM | #22 | |
Second Lieutenant
8
Rep 277
Posts
Drives: '11 E90 N52 6MT
Join Date: Feb 2012
Location: here
|
Quote:
|
|
Appreciate
0
|
Bookmarks |
|
|