|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
E90 bixenon headlight 3 led corner help
|
|
02-09-2024, 06:40 AM | #1 |
Private
8
Rep 60
Posts |
E90 bixenon headlight 3 led corner help
Hello
My e90 is pre lci 2006 I'm changing my headlights from halogen to bixenon, I think they call it the European version of headlight. 1vision prepared a harness for me, it works perfectly but I would like to know how to make the 3 LEDs that are up on the side work. I attach an image and a video on Google Drive of how it works. Video : https://drive.google.com/file/d/18q4...ew?usp=sharing My FRM is FRMFA.C12 Do you know if I have to code something for these 3 LEDs? Now I also saw on the forums that with my frm I can't have angel eyes DRL What are my options? Change the FRM? Any change in the wiring? This is not important, for now I want to leave the headlight 100% functional Thank you Last edited by warlockuy; 02-09-2024 at 08:34 AM.. Reason: add data |
02-09-2024, 02:04 PM | #2 |
Private
8
Rep 60
Posts |
Solved good brico solution, tape pin 1 to 7, when the angel eye turns on, these 3 LEDs too.
Now I only have the problem that when I start the engine the light comes on and off. On Sunday I'm going to charge the 522 to the vo and I'll try that, if this works I'll take it apart and install the headlights later in the week. Will keep you informed |
Appreciate
0
|
02-09-2024, 11:14 PM | #3 |
Robot
1689
Rep 2,192
Posts |
You're correct that you can't have angel eyes as DRLs. Pre-LCI halogen cars use the high beams as DRLs and there's no way to code that. You could get creative with hard wiring it to a relay but it's definitely not a clean factory-like setup.
The three amber LEDs in the LCI lights are specific to the LCI lights and aren't supported by any of the pre-LCI FRMs, so you can't enable them via coding. If I remember correctly there's not even a wire present in the pre-LCI connector on your car, so if you want them to work like they do in the LCI cars you'll need a FRM3 and run a new wire from the FRM harness to the connectors at both headlights. Are the amber LED turn signals in your new lights turned ON all the time? If so you'll want to code those out. They're too bright to be left on all the time whenever headlights are on. SIDEMARKER_US = nicht_aktiv What lights are going on and off when you start the car? The headlights flickering? If so, that's likely the bulb checks. Your FRM is programmed for halogen headlights. Add $522 to the VO and default code the FRM and that should take care of it. (Depending on how comfortable you are with coding you can either set SIDEMARKER_US to nicht_aktiv when you get the default .TRC file, or you can just follow a guide for default module coding, and then code again changing the side marker setting.) Do you know how your high beams are configured? Did you do any wiring modifications to the LCI lights that you got? If no wiring modifications the high beams likely won't work at all. You'll need to wire the xenon shutter to the high beam wire inside the headlight; however I chose not to do that because the inner lights on the LCI Xenon headlights (at least the adaptive ones that I got) are cornering lights not meant to be left on long since they generate a lot of heat. The safest thing if you choose to do the wiring inside the headlight would be to not use the inner cornering lights at all; disconnect it from the bulb base and wire it to the xenon shutter. I wanted a factory-like clean setup so when I converted from Pre-LCI halogen to LCI Xenon headlights on my 325 E90 I had to run a new wire from a pin on the harness at the FRM to each headlight for the high beam shutter. I tried coding the FRM module with $522 and still had no high beams, only to realize I had to buy a new FRM that supported Xenons. It's marked on the FRM itself. Hope this helps. It sounds complicated but it's really not, just need to figure out what you want to do. Just read a lot on this site, but keep in mind that the E90/91 and E92/93 headlight setups are completely different so don't get distracted reading E92/93 headlight modification tutorials like I did. |
Appreciate
0
|
02-10-2024, 08:30 AM | #4 | |
Private
8
Rep 60
Posts |
Quote:
At this moment I only have the problem of flickering the lights. But still don't add to the VO at $522. This Monday, when I'm on vacation, I'm going to do it and if you don't blink, I'll take apart the front and install it. I'll tell you what I have working. First 1Vision made the harness for me and I modified it a little. Now they work for me angel eyes Bixenon low and hi. 3 Led corner Sidemarker Autoleveling Manual leveling from the control Could you tell me which modules I should leave by default after adding VO $522? and write frm and cas. First I make a backup of each one and then I overwrite blank. In the frm I found that it has to be able to put bixenon, so it should work with the VO $522 I leave you some lines that I found in the frm, with the dummy I can see your options. Search Xenon in frm BI_XENON_FL_ABSCHALT_OPT wert_02 BI_XENON_BEI_LH nicht_aktiv XENON_WIEDER_Z_AUS_PHASE wert_01 PWM_ANST_FL_BIXENON wert_01 XENON_AL_VERBAUT nicht_aktiv BI_XENON_VERBAUT nicht_aktiv XENON_WIEDER_ZUEND nicht_aktiv XENON_LI wert_01 XENON_WIEDERHOL_Z_OPT nicht_aktiv Very very thanks Last edited by warlockuy; 02-10-2024 at 08:36 AM.. |
|
Appreciate
0
|
02-13-2024, 09:52 AM | #5 |
Private
8
Rep 60
Posts |
Solucionado
|
Appreciate
1
johnnyorange58.50 |
Bookmarks |
|
|