|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Code out Adaptive Headlights?
|
|
11-22-2012, 09:57 PM | #1 |
Lieutenant
99
Rep 508
Posts |
Code out Adaptive Headlights?
Greetings,
I am still pretty new to coding but have had pretty good luck so far. This all started with an injector going bad... Using IMPALOAD I was able to code my injector without issue Then I figured what the hell, I have the cable! Since then I have been using NCSEXPERT and have coded folding mirrors, removed seatbelt dings, removed IDrive startup warning, digital MPH, etc. Now a few months ago, moisture found its way into my pass headlight causing the famous adaptive headlight failure... My question now is what do I need to do to remove this check from my car? I have searched for the past day or so and have not found much in terms of a DIY. I have read that I need to remove $524 from VO but I have NO idea how to do this... YET! |
11-23-2012, 11:37 AM | #3 | |
Lieutenant
99
Rep 508
Posts |
Quote:
Your the man! This is exactly what I was hoping to see. So with the PDF example, they are adding $655 into the VO. Is it safe to assume that I need to find $524 in my list and simply delete it and then follow the rest of the steps in the guide? Thanks again, |
|
Appreciate
0
|
11-24-2012, 10:23 AM | #5 |
Lieutenant
99
Rep 508
Posts |
So I can get to the ADD screen but can not delete the $524...
I will keep searching but if someone has an answer on how to delete I would appreciate it greatly. Regards, |
Appreciate
0
|
11-24-2012, 10:38 AM | #6 | |
441
Rep 18,331
Posts |
Quote:
Here is the PDF on deleting VO..page 8 |
|
Appreciate
0
|
11-24-2012, 11:13 AM | #7 | |
Lieutenant
99
Rep 508
Posts |
Quote:
I have also changed CHECK_SMC_ERROR in the NFRM to nitch_active to turn off this check. I still have the Addaptive error... Double checked and $524 is no longer in my VO... Do I need to remove/clear the stored error code from the car? Or is there something else that I have missed? Thank you for your help and patience. Last edited by trickcruiser; 11-24-2012 at 11:48 AM.. |
|
Appreciate
0
|
12-04-2012, 05:02 PM | #11 |
Brigadier General
300
Rep 4,444
Posts |
Sounds like you just deleted the VO... you then need to FA_Write to CAS and NFRM/FRM, THEN recode them (All of these steps in expert mode).
Please read the DIY and instructions carefully first before half coding your cars |
Appreciate
0
|
12-05-2012, 07:39 AM | #12 | |
Lieutenant
99
Rep 508
Posts |
Quote:
I switched CHECK_SMC_ERROR to nitch_active when I did my initial coding (mirrors, windows, etc.) hoping it would eliminate the code. After deleting the option from my VO I went back and changed DYNAM_LWR_ENABLE to nitch_active. So I should do the following: 1: Change CHECK_SMC_ERROR and DYNAM_LWR_ENABLE to active in NFRM using Expert Mode 1: Ensure that $524 is deleted and FA_Write (again) to CAS and NFRM/FRM in Expert Mode 2: Code CHECK_SMC_ERROR and DYNAM_LWR_ENABLE to nitch_active in NFRM using Expert Mode I have a feeling I have made this much more difficult than it has needed to be... Thank you for trying to help, I truly appreciate it. |
|
Appreciate
0
|
12-05-2012, 12:00 PM | #13 |
Brigadier General
300
Rep 4,444
Posts |
No between FA_Write step and your next one, you need to SG_Codrien the effected modules.
That's the point of VO editing... you shouldn't need to code individual lines after properly updating and programming from the VO. |
Appreciate
1
stepheng2732.50 |
12-11-2012, 11:57 PM | #14 |
Private
5
Rep 55
Posts
Drives: 2011 BMW E92 M3 Coupe
Join Date: Dec 2012
Location: Fernandina Beach FL
|
i'm a newbie to bmw's but did some very basic coding to an Audi 2.7T many years ago. can you guys point me to where I can go to get details on how to code my 330Xi? thx.
|
Appreciate
0
|
12-12-2012, 01:42 PM | #16 | |
Lieutenant
99
Rep 508
Posts |
Quote:
I will be trying to code out the adaptive headlights this evening! I will update on how it goes. Appreciate the guidance! |
|
Appreciate
0
|
08-08-2014, 09:40 PM | #19 |
Enlisted Member
3
Rep 39
Posts |
Guys I have the same problem. I need to remove $524. I did it successfully for CAS. But, when I change ECU to FRM, I'm getting this error:
Error in CABD! Look at CABI.ERR and ERROR.LOG! COAPI-2000: Fehler in EDIABAS oder in SG-Beschreibungsdatei SYS-0005: SG-Beschreibungsdatei nicht gefunded FRM_87 COAPI-2000: Fehler in EDIABAS oder in SG-Beshcreibungsdatei SG_CODIEREN Please help me I've been stuck for 5 days now...
__________________
|
Appreciate
0
|
08-09-2014, 01:49 AM | #21 |
Enlisted Member
3
Rep 39
Posts |
I got the daten files from here http://www.e90post.com/forums/showthread.php?t=882353
so i guess its 50.2 Do you know where I can get the latest one that will work for me? Thanks!
__________________
|
Appreciate
0
|
Bookmarks |
|
|