|
|
|
|
PLEASE HELP SUPPORT E90POST BY DOING YOUR TIRERACK SHOPPING FROM THIS BANNER, THANKS! |
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
19x11 on prelci e90/91 what offset??
|
|
Wheels and Tires forum Sponsored by The Tire Rack
Please help to directly support e90post by doing your tirerack shopping from the above link. For every sale made through the link, e90post gets sponsor support to keep the site alive. Disclaimer |
|
Thread Tools | Search this Thread |
02-10-2016, 01:54 PM | #1 |
Enlisted Member
15
Rep 33
Posts
Drives: F31 320i Stage 2
Join Date: Mar 2013
Location: Netherlands
|
19x11 on prelci e90/91 what offset??
Stance homies
Need advice want to get 19x11 on 265 35 19 I do not want to go camber Of course i know i will need to roll fenders What is the correct offset? I was thinking of et25?
__________________
BMW F31 - 320i N20B0 - Stage 2 - 3" Catless Downpipe / FMIC / Alu Charger Pipes / K&N Inlayfilter
Last edited by tom3touring; 02-15-2016 at 07:40 AM.. |
02-11-2016, 06:09 PM | #2 |
BimmerPost Supporting Vendor
2038
Rep 25,989
Posts |
Here you go! This is 19x11 ET25 with a 265/30/19 tire. The fronts are 19x9.5 ET33 w/10mm spacer and a 225/35/19 tire.
You can see how close the fitment is in the last pic. There is camber, but not an overwhelming amount.
__________________
VMR|Wheels | 714.442.7916 |
sales@velocitymotoring.com | www.velocitymotoring.com | facebook | flickr | Instagram |
Appreciate
0
|
02-11-2016, 07:41 PM | #3 |
Hola
70
Rep 407
Posts |
|
Appreciate
0
|
02-12-2016, 04:16 AM | #4 |
Captain
240
Rep 883
Posts |
19x11 et25 & 265/30 will be fine. You will need to shave the rear and slight pull at certain points of the fender (with wheels fitted) to make sure nothing rubs under full compression. Camber should be around -2.1. Hope this helps
__________________
|
Appreciate
0
|
02-12-2016, 12:45 PM | #5 |
Major General
223
Rep 5,120
Posts |
If you are trying to avoid camber that is an agressive fitment. I have 11"et33 275/30/19 -1.8 camber. I had to roll the fenders and shave some off by the rear bumper. I am lowered on bc coils with 10k and 16k springrates. There is still room on the inside 11"et40 would fit easier.
|
Appreciate
0
|
02-15-2016, 07:39 AM | #6 | |
Enlisted Member
15
Rep 33
Posts
Drives: F31 320i Stage 2
Join Date: Mar 2013
Location: Netherlands
|
Quote:
Wise advice. So you still have a little gap now on the inside to go deeper?
__________________
BMW F31 - 320i N20B0 - Stage 2 - 3" Catless Downpipe / FMIC / Alu Charger Pipes / K&N Inlayfilter
|
|
Appreciate
0
|
02-15-2016, 06:48 PM | #7 |
Major General
223
Rep 5,120
Posts |
There is over 1/2"(at least 13mm) between the strut and wheel at 11"et33. 11"et40 would be fine.
Last edited by bmw325i; 02-15-2016 at 06:55 PM.. |
Appreciate
0
|
Bookmarks |
|
|