|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
DIY on crack open the e90 LCI headlight?
|
|
11-16-2012, 01:43 AM | #23 |
Brigadier General
186
Rep 4,732
Posts
Drives: Alpine White '13 550i
Join Date: Nov 2011
Location: Tarzana, CA
|
Good to know you did it without damaging anything, you really should have done another DIY for us all.
|
Appreciate
0
|
11-19-2012, 12:15 AM | #24 |
Major
39
Rep 1,154
Posts |
I've opened headlights on a few cars by throwing them in the oven at 225 for 15 minutes. Is there any reason these lights can't take the heat?
__________________
2016 340i xdrive
2009 335i |
Appreciate
0
|
11-19-2012, 11:17 AM | #25 |
BimmerPost Supporting Vendor
469
Rep 4,938
Posts |
Doesn't work with the E90 headlights. They use a different glue that isnt affected by heat. It will only get hot and not soft
__________________
|
Appreciate
0
|
11-19-2012, 01:11 PM | #26 |
Major
39
Rep 1,154
Posts |
Now i'm confused, what does a heat gun do then?
__________________
2016 340i xdrive
2009 335i |
Appreciate
0
|
11-19-2012, 02:20 PM | #27 | |
Colonel
141
Rep 2,217
Posts |
Quote:
Even though i had some hiccups along the way, it definitely was not because of the cutting process, but because i had shitty headlights to start off with. I've since then had plenty of practice on other peoples' headlights and i think i have it down pat now... ^__^ EDIT: And to add on to LUX's comment, i've tried the heatgun method, it doesn't work... the headlight lens will melt and bubble up before the glue gets soft/sticky in order to peel apart. I also tried heating up just the black housing part (directly behind the clear lens) and again, the housing gets soft and malleable before the glue does. If there's another method out there that someone KNOWS works, then please make a video of your process in order to not only prove me wrong, but to help the rest of use have a clean and professional project we can be ultimately proud of. ^__^ The reason the glue doesn't work like other headlights is because this (like the new GM/Chevy vehicles) headlight uses "Perma-Seal Gasket" it's an epoxy that resists heat below 500°, it's commonly used in making valve cover gaskets. Thus, why a heat gun has no effect. Last edited by N0OS3; 11-19-2012 at 02:31 PM.. |
|
Appreciate
0
|
11-20-2012, 12:50 PM | #28 | |
BimmerPost Supporting Vendor
469
Rep 4,938
Posts |
Quote:
I have opened up about 30 of these headlights since i used to the the CF wrap over the amber part. You need to set the heatgun to a fairly low temp so that the black plastic gets soft but not hot enough to burn or bubble the clear lens. After that you need to slowly pry the black plastic up so you can start breaking the seal on them. its not an easy process and its rather back breaking. You need to use a screw driver to break the seal and rip the glue apart that way
__________________
|
|
Appreciate
0
|
11-20-2012, 05:30 PM | #29 | |
Banned
151
Rep 2,638
Posts |
Gently heats up the plastic housing to allow space for a screwdriver to get underneath and brake the seal.
Quote:
|
|
Appreciate
0
|
11-21-2012, 01:06 PM | #33 |
BimmerPost Supporting Vendor
469
Rep 4,938
Posts |
Now thats what i'm talking about!!! good job scraping all the old glue from everything.
__________________
|
Appreciate
0
|
11-21-2012, 08:36 PM | #34 | |
Banned
151
Rep 2,638
Posts |
Quote:
Well, I used your guidance to get through it. I just refuse to take cutting to be the answer. I am awaiting my orion v4's so I can smack these babies back together again. The other side of the housing isn't as good as this one. I fudged it a little at the top because I didn't perfect the process. I think I have a pretty good handle on it now. I can't wait to do another set. |
|
Appreciate
0
|
11-23-2012, 09:13 AM | #36 |
Banned
151
Rep 2,638
Posts |
|
Appreciate
0
|
05-02-2013, 08:45 AM | #37 |
New Member
0
Rep 10
Posts |
I'm trying to do a similar process on the X5 forums for my headlights, and agree that a blowdryer is much more controlled heat and less chance of mangling the plastic of the housing. did you just use one small thin screwdriver, or a thicker one to get under and break the seal? I see a lot of the DIY's showing these big flat heads like a pry bar and all it does is mangle the housing, yours is CLEAN and any helpful tips would be appreciated! |
Appreciate
0
|
05-02-2013, 10:33 AM | #38 |
Private First Class
13
Rep 188
Posts |
I just did a projector retrofit with led rings for my pre-lci. and as mentioned before all I used was a heat gun a butter knife and a lot of patience. Took about 1 or 2hrs a light.
|
Appreciate
0
|
05-02-2013, 10:49 AM | #39 |
New Member
0
Rep 10
Posts |
OK I will keep that in mind, thanks for the input! Butter knife is a good idea, usually they are thick enough to make a good prying tool but not sharp enough to mangle up much.
|
Appreciate
0
|
05-03-2013, 11:11 AM | #41 |
Lieutenant Colonel
118
Rep 1,933
Posts |
Not an easy task in any form. Our local lights guy here doesnt wanna touch any e90 lights cuz theyre a PITA.
If you really wanna DIY, i hope you have experience as these are not cheap to buy or get fixed |
Appreciate
0
|
05-03-2013, 11:22 AM | #42 | |
New Member
0
Rep 10
Posts |
Quote:
details on the process you used? yours being opened is the cleanest job I've seen yet, which is why i'm interested on how you opened so cleanly. A detailed description along with tools used to pry (besides blowdryer) would be helpful, thanks |
|
Appreciate
0
|
05-11-2013, 07:21 PM | #43 |
Banned
151
Rep 2,638
Posts |
I just used a small flathead screwdriver to break the seal. I have a secret after that but I am holding on to it in case I decide to do these for others. Lastly, be very careful with the lens. As stated earlier, these are not cheap. If you damage the lens in any way, you need a whole new set.
|
Appreciate
0
|
05-11-2013, 07:30 PM | #44 | |
First Lieutenant
27
Rep 342
Posts |
Quote:
|
|
Appreciate
0
|
Bookmarks |
|
|