[Tepr05]

Oil filter housing gasket, oil cooler housing gasket, serpentine belt, ER charge pipe, and reforming some plastic on my inlet pipe where it connects to the air box pipe.

[connor92]

Finished up my LED interior light conversion. The front dome light was a pain.

[NitroKing]

Originally Posted by connor92

Finished up my LED interior light conversion. The front dome light was a pain.

I know the feeling, so worth it in the end lol.

[ny325]

Let my E90 Idle for a few minutes since I haven’t driven it for a few days.

[Blue E92]

Originally Posted by connor92

Finished up my LED interior light conversion. The front dome light was a pain.

It wasn’t too bad if you unscrewed the two inner visor clips from the headliner. You could then pull the headliner down enough to get your hands in to pop both little tabs from the inside.

[Dan Bilzerian]

Originally Posted by TGSN_

The ebay headlights passenger side angel eyes went out. It kind of bothered me so I decided to take the time to restore the oem xenons and reinstalled them. I'm tempted to take the ebay ones apart and redo the rings. I believe they were equipped with CCFL, so LED would be a good move. But I will probably just sell them.

What did you use to get the headlights that clean?

[TGSN_]

Originally Posted by Dan Bilzerian

What did you use to get the headlights that clean?

I used the 3M 39008 Headlight Lens Restoration System, Meguiar's Ultimate Compound (instead of the one in the kit), then several coats of wax to finish it off.

[TGSN_]

Originally Posted by nuron

who made those ebay lights? and how is the projector cutoff?

OEMASSIVE was the seller on ebay. The cutoff was kinda off for me, the line was not as clean as the OE Xenons. But it got the job done when it came to visibility.

[tetsuo111]

Accomplished a few projects over the Holidays:

1) installed Philips X-treme Ultinon H7 LEDs for high-beams. These are significantly brighter than the halogens they replaced. Since they're high beams, scatter and glare aren't a concern. Installation required minor modification to the headlamp housing.

I plan to test another pair of Philips LEDs in the low-beam position. This application will need further mods to the headlamp housing to fit the large LED housing.

2) the car was aligned to OE specs. the rear-end was extremely loose and the car hadn't been aligned since taking delivery. the pax-side rear was toed out. The toe-out was remedied and the car tracks straight and feels stable now.

3) installed Turner 60A motor mounts and OE E30 trans mounts (stiffer than the hour-glass shaped E90 mounts). Thanks, feuer!

4) installed M3 front undercarriage stiffening plate to mitigate chassis flex. I haven't seen this on another non-M. I believe mine is the first.

5) installed M3 cluster. this completes my M3 interior conversion. the motivation for this was my desire to monitor coolant temps without having to access hidden menus, and simple aesthetics. I feel both goals were accomplished

[delmarco]

Shoveled it out after a month of being parked and Jump Started it using what is essentially a cell phone charger! lol

[connor92]

Originally Posted by Blue E92

It wasn’t too bad if you unscrewed the two inner visor clips from the headliner. You could then pull the headliner down enough to get your hands in to pop both little tabs from the inside.

Actually the trick is to first take the dome light cover off, then take the map light surrounds off, the tabs will be exposed, you then take a paper clip and pull the tabs towards you. Came off in 30 seconds!

[Greyfox]

Started building a hard drive for my laptop to do coding.

[Tim_354841]

Took it in to diagnose fan cycling and high fan speed during 8 degree weather, power cuts, not coming up to normal oil temp, etc. Expecting water pump replacement

[Dan Bilzerian]

Pulled some codes and got ABD1 in the MASK/ccc ecu.
Tried looking it up but no luck. Any insight?

[minaret]

Installed front M3 LCA. Due to winter ride height max camber from LCA and TC Kline camber plates is -2.75. Wonder how much of a drop yields -3.0 neg camber? I also removed the fold-down rear seats and cargo security screen; saved 77 pounds.

[CaddymanLNL]

Originally Posted by minaret

Installed front M3 LCA. Due to winter ride height max camber from LCA and TC Kline camber plates is -2.75. Wonder how much of a drop yields -3.0 neg camber? I also removed the fold-down rear seats and cargo security screen; saved 77 pounds.

you selling that security screen/roller-kombi thing?

[raja101]

Looks amazing. What product do you use for the wax?

[tlow98]

Originally Posted by minaret

Installed front M3 LCA. Due to winter ride height max camber from LCA and TC Kline camber plates is -2.75. Wonder how much of a drop yields -3.0 neg camber? I also removed the fold-down rear seats and cargo security screen; saved 77 pounds.

I believe it! that security screen housing must weigh 35lbs alone. It's an incredible anchor.

[beo420]

Today i got installed an anti-theft system and tinted my windows black a bit.

[N54Twin]

Replace VTG module

Shit was causing the Christmas tree i had in my cluster.

[BeastMode335i]

Listed it for sale =)

[Lifelike]

Had to pop the plastic casing off of the rear side of the center console so I could fish my aux-port wire back through the hole because the entire plastic input piece fell in.