[Chrisred]

Originally Posted by Sensible_

Ok, well you can always ask for help...

I assume this is an e92 with FRM2?

2 ways:

1. Add +MUEB (+MUH2 for FRM3) to the CAS and NFRM VO. Then FA_WRITE both. Then code NFRM to default with SG_CODERIEN.

2. Disable cold and warms bulb checks:

NFRM

KALTUEBERWACHUNG_BLK_H -> nicht_aktiv
KALTUEBERWACHUNG_BL -> nicht_aktiv
KALTUEBERWACHUNG_BFD -> nicht_aktiv


WARMUEBERWACHUNG_BLK_H -> nicht_aktiv
WARMUEBERWACHUNG_BL -> nicht_aktiv
WARMUEBERWACHUNG_BFD -> nicht_aktiv

Yes frm2. Thx I'll try. Appreciated!!

[WidE92]

Reviving for some help....

I have an early production 2007 E92 (4/06) and for some reason I cannot get the counter to work for frm70. I can run it for frm87 and it simply states okay. I must be doing something wrong but when I go into INPA and try to load the FRM it only detects FRM87. Do I not have it?

[Stouer2020]

Originally Posted by undermine

I figured this out.

You have a newer E-Series I assume, use reset_kurzschluss_sperre, enter just a number 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, and so on, individually but with out the comma, get it? Some people just go through 0-255 but I went through 0-64, cleared every error in my FRM.

If this is not clear, let me know.

Bonjour je sais que ces un vieux topic mais je voudrais enlevé un court circuit sur un BMW E90 car j'ai mit un FRM3 à la place du FRM2 et le feu de stationnement ne fonctionne pas

[Ldee247]

Hi guys...

Sorry for hijacking this post as I have a similar problem with BMW X3 and I'm kindly asking for your help.

I have a BMW X3 E83 2.5i 2004 Model and have changed my original headlights to Angle lights and only the driver's side Low beam has stopped working. I tried changing the bulbs but still, it didn't work I have also swapped the headlight units from left to right and realised the problem lies on the right-hand side as both lights only work on the passenger's side.

I bought the K+DCAN with a switch and have installed BMW INPA software on Win 10 but I'm stuck on which counter short circuit modules that need resetting as mine it's an E83 2004 model.

Any help I would greatly appreciate...

Thanks

[mizta insane]

Use tool32 and reset frm count status and post here

[Ldee247]

Originally Posted by mizta insane

Use tool32 and reset frm count status and post here

Hi, and thanks for the prompt response I really appreciate since my model is an E83 would you know which FRM to load and reset in relation to my model E83 inside Tool32?

From the earlier post in the forum, I've seen guys been talking about specific frm_70.prg and frm_87.prg or it doesn't matter?

[335iguy17]

When i select e90 (FRM3) in the list under body only FRM87 shows and then when I click it it only says FRM87 requested but only frm70 found and program will be stopped?

[Hennye90]

Is there anyone here that could do this remotely for me ? Idm paying i just need my angel eyes back😂

[DeobandiPrince]

Originally Posted by mizta insane

Use tool32 and reset frm count status and post here

Since I bought my car, I always noticed that the passenger DRL (only when the engine was off. When the engine would turn on, it would be fine) would flicker ever so slightly (not flicker from on to off but on to slightly less dim)

One weekend there was a lot of heavy rain and a couple times the passenger DRL (angel eyes) would go out but would come on after I cycled the ignition on or just let the car sit for a while. At some point the DRL (angel eyes) stopped coming on all together.

I have some eBay HID's that I swapped sides and the passenger DRL still stayed off. I swapped the ballast around too but still no luck.

Had a 9CBB code.

I tried resetting the FRM counter thing via Tool32 and the DRL would come on for like 30-40 seconds but still have that slight flicker (almost unnoticeable but if you looked at it, you could tell it flicker from bright to slightly less bright)

Still have a A8C6 code also in the FRM module I also have a 9CC3 code. 9CBB code is no longer present.

Not sure what to do now. I've rest the DRL counter twice now and from what I understand, you can only reset the counter 5 times after which you need to replace your FRM which I would like to avoid. I was thinking of buying a working headlight from elsewhere and try plugging that in and resetting the counter.

That would put me at 3 resets with 2 left and that point it could be the FRM and/or wiring?

How would I know if it was FRM? Could it be wiring? The DRL's turn on when I reset the counter but flicker a bit before going out so not sure.

Any guidance on troubleshooting this issue?