[Sensible_]

Originally Posted by dumitru.o

xprog 5.55 china

thanks

Can you show me log and take photo of the PCB please...

[dumitru.o]

i will do that at the end of the week when i am hope. the thing is that i was able to delete and write the EEE and then i read the p-flash without problem, then i delete the p-flash to with the new one i had from dump and since that moment i was unable to do anything else then delete (EEE and p-flash). if i try to delete it say s that it s secured. i try with the secure profile but does nothing when i try to reset security....

will be back with pics and log

[Mik325tds]

Originally Posted by dumitru.o

i will do that at the end of the week when i am hope. the thing is that i was able to delete and write the EEE and then i read the p-flash without problem, then i delete the p-flash to with the new one i had from dump and since that moment i was unable to do anything else then delete (EEE and p-flash). if i try to delete it say s that it s secured. i try with the secure profile but does nothing when i try to reset security....

will be back with pics and log

Try using the non-secured profile. That has worked for mine after something similar happened.

[dumitru.o]

tried without success

[Mik325tds]

Originally Posted by dumitru.o

tried without success

Are you powering the Xbox by USB only? Mine had problems with that. After using an external power supply it worked much better. The reads are still flaky but the writes usually work fine.

[dumitru.o]

i also used external power supply , but without any difference.

[Sensible_]

Maybe it's a problem with your XProg. Have you confirmed its working on other MCU's?

[Levanime]

Originally Posted by Sensible_

Maybe it's a problem with your XProg. Have you confirmed its working on other MCU's?

Could you please recommend good source for good quality Xprog?
i want to try doing this

thanks!

[Sensible_]

Originally Posted by Levanime

Could you please recommend good source for good quality Xprog?
i want to try doing this

thanks!

This one has good reviewed and is latest 5.55. A clone obviously but quality seems ok.

http://s.aliexpress.com/AzEJBbmA
2016 Lastest version Xprog M 5.55 ECU Programmer Xprog-M V5.55 ECU Chip Tuning Tool with full set X prog m V5.48

[Levanime]

Originally Posted by Sensible_

This one has good reviewed and is latest 5.55. A clone obviously but quality seems ok.

http://s.aliexpress.com/AzEJBbmA
2016 Lastest version Xprog M 5.55 ECU Programmer Xprog-M V5.55 ECU Chip Tuning Tool with full set X prog m V5.48

thank you!

[Levanime]

deleted

[y3k10]

I found this p-flash in your collection : FRM E87 E92 E93 6135 9240528-01 SW 132001 HW 07.rar and its the same like my bad FRM. But there is only p-flash in it and not eee. is it enough to write p-flash without eee dump?
i tried to read p-flash but i am getting device is silent.

[Levanime]

no, you need eeprom

[y3k10]

I changed latency in driversettings from 16ms to 1ms. Then it Starts Reading p-flash but Same Problem with Device is silent. Eee i can read just Fine. Any suggestions where to get eee Dump for this frm? Will it fix the Reading error for pflash if i flash eee First?

[Levanime]

looks like your programmer problem,
good eee will not help P-Flash reading problem

[y3k10]

I have 5.55 clone. With Dongle Tool does not start up. So i tried with no Dongle Tool. Eee can read and it says wrong Partition Table but i can Read eee with Partition set to 16.
You have a Suggestion what to do? And which dump to take?

[y3k10]

can eee flash make frm work in car to flash again or is eee and p-flash neccessary?

[y3k10]

Tried everything. Only using serial cable instead of USB solved the problem. Now its working fine. Only verification does not work and gives errors but should be no problem

[Bl@nquito]

Hi to all! I'm new here

I've been reading some information about the FRM module since mine is kind of bricked...

Maybe you can help me. The problem is that dealer was coding and suddenly the update failed. He wasn't able to connect to the module anymore.
He got it repaired but now the obd is working, but if we try to update it, it fails. Just no chance.

All this is using the official ISTA with the license to operate connected to Munich

Do you have any ideas? Also the diagnostic throws an error with the ambient light sensor that was not present before... In case it helps

The reference must be for the VIN E766945 61359390491
Adaptative headlights, memory seats, interior lights, LCI since its 2011, etc.

[Levanime]

its fried,

you need good eep

[Bl@nquito]

Originally Posted by Levanime

its fried,

you need good eep

Thanks for replying!

Do you know which eep from the google drive posted before could fit?
Unfortunately dealer didn't make any backup of it...

[Levanime]

post picture of the unit itself where numbers are written,
you need to chose by part number