E90Post
 


Coby Wheel
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > DIY Guides > e9x "M3" White Gauge Cluster



Reply
 
Thread Tools Search this Thread
      08-03-2012, 09:39 AM   #89
makkan00
Major General
makkan00's Avatar
United Kingdom
886
Rep
9,094
Posts

Drives: F36
Join Date: Dec 2011
Location: Essex

iTrader: (56)

Nigel, any update on soldering fresh LEDs?
__________________
F36 Xdrive for her - HUD, park assist, heated steering wheel, rear camera, Apple car play
F36 RWD for him - HK, M sports pack, GTS tail light, Apple car play
Appreciate 0
      08-03-2012, 11:44 AM   #90
Nigelo
Lieutenant
30
Rep
540
Posts

Drives: E92 335i se
Join Date: Aug 2011
Location: Northern Ireland

iTrader: (1)

Not yet chief, been still faffing around trying to get the needles correct - particularly concerning the white colour leaking through the m5 needles. Saw a pic of a m-something cluster with red coloured plastic around the needle pins which might be the answer I'm looking for.

Another thing I've been looking for is info about a resistor on the cluster that if removed should give extra brightness and is absent from the actual m3 cluster.
Appreciate 0
      08-03-2012, 04:11 PM   #91
cypis007
Private
Poland
0
Rep
83
Posts

Drives: E91 318d Touring
Join Date: Nov 2011
Location: Capital

iTrader: (0)

Little offtopic but I think useful.

Recently I did install custom cluster faces.

Started with this:



As you can see that's LCI, diesel (so no M3 option in range), without cruise control ring.

After cluster disassembly I've sent original faces to company which made custom ones. They scanned them and build base for project, which fits perfectly as replacement. Top notch job.

I hate zyllions of marks on speed gauge, and too many of them (for my taste) on RPM gauge.
For my project I decided to mix ideas from Audi A4 B8 and E90 with cruise control. I ended up with this:





Clean, sporty and far, far modern than BMW's Times New Roman ;-).

I decided also to put pre-LCI speed and RPM needles as they fit better with fuel and consumption gauges.
Here is comparison - left LCI, right pre-LCI:



Note pre-LCI needle is slightly brighter than LCI. It is not uncomfortable for me - more important indications (speed and RPM) are better marked.

Here is final effect:







Note slightly darker spot under 80 hm/h (left) and 4 rpm/min (right) - I'm unsure what is the reason (original backlight or faces quality issue) but I'm already in process of Stg 2 modification which are faces with indiglo backlight and M5 needles.

Should came this way (drawing photo):



I will order same faces but on white indiglo base and will power it from permanent 12V somewhere in cluster, because programming permanent LED backlid (like in M3) doesn't work with my KOMBII (cluster) module.
This way I'm not going to solder new white LEDs (even if I bought them already, various ideas constantly flying in my head..) in cluster board. Will see if it works.

One more thing regarding needles: LCI needles are mounted on 1.5mm pole, where pre-LCI are mounted on 1mm pole.
I hope that will be enough for M5 needles and Nigelo's mod will not be necessary. ;-)

Regarding positioning needles on zero location, on speedo example:
- disconnect cluster
- install needle on 9 o'clock position
- push it gently towards zero position - this MUST be done by slipping needle around stopped pole (hinge-like)
- if needle sits tight and don't want move under your finger, increase needle mounting hole diameter by drill until you can turn needle on stopped pole (counterclockwise).
This way I did installation of second pair of needles in 5 minutes, where first pair took me 2 hrs and I wasn't happy with effect.

Hope it helps.
Appreciate 0
      08-03-2012, 09:54 PM   #92
F31cruisin
Lieutenant
47
Rep
465
Posts

Drives: 330i
Join Date: Jan 2011
Location: Florida

iTrader: (11)

Quote:
Originally Posted by makkan00 View Post
Post some photos of end product.
I switched the amber lights to the white LED's in just the gauges, I bought the M3 backing plates, and aftermarket M3 rings (which I painted sliver). Absolute pain to install the rings. You have to basically break off the glass from the front part of the cluster to install the rings.

For the needles, I ended up taking the white paint off from the needles and painting it red from the back. If I did it again, I would take the needles off of the black caps to really get all the paint off the inside and paint it right. You can see a bit of light shine through at the edge of the black cover where the red paint isn't at. Still looks great, and not blotchy at all.



Last edited by F31cruisin; 08-03-2012 at 10:15 PM..
Appreciate 0
      08-18-2012, 05:13 PM   #93
DuckySpud
Captain
DuckySpud's Avatar
United Kingdom
23
Rep
662
Posts

Drives: 320D Touring
Join Date: Jul 2012
Location: Sheffield

iTrader: (1)

Did my dials yesterday and pretty pleased with them. Just did the dials and not the center LCD display. Just sharpied the top of the needles too. I may change them and colour the underside of them instead, seen other people do that and think it looks a bit better. Anyway, its a fairly standard photo, but here is the result

Appreciate 0
      09-07-2012, 08:03 AM   #94
swc945
Enlisted Member
Australia
8
Rep
36
Posts

Drives: E92 325i
Join Date: Feb 2012
Location: Melbourne

iTrader: (0)

Thanks for the DIY guide!
I just ordered the LEDs and will be crossing my fingers thatt i don't ruin my instrument cluster...but thanks for the detailed write-up and all the subsequent contributions from others
Appreciate 0
      09-07-2012, 12:23 PM   #95
e90TiAg335i
Major
e90TiAg335i's Avatar
United_States
124
Rep
1,151
Posts

Drives: 10 e90 335i
Join Date: Mar 2010
Location: jacksonville, FL

iTrader: (10)

Garage List
2010 e90 335i  [7.00]
Quote:
Originally Posted by swc945 View Post
Thanks for the DIY guide!
I just ordered the LEDs and will be crossing my fingers thatt i don't ruin my instrument cluster...but thanks for the detailed write-up and all the subsequent contributions from others
You're quite welcome! I'm confident you won't have a problem.
__________________

JB4, DP, VMR V710, Sonic Tuning S1 coilovers, Hybrid Ovations, Soundsplinter 10" and Zapco DC Ref amps
Appreciate 0
      10-02-2012, 04:19 PM   #96
pablo86
Registered
0
Rep
3
Posts

Drives: 320d
Join Date: Sep 2012
Location: Cambridge

iTrader: (0)

Hi,

I have changed the LED's on my car and when I test the gauges with the needle sweep the speedo does not rotate around and back. It starts clicking and then stops.

I have reset the worm at the back and made sure it is all lined up ok but this does not change anything.

Is there anything else I can do or will i need to replace the cluster?

Many thanks
Appreciate 0
      10-03-2012, 09:43 PM   #97
e90TiAg335i
Major
e90TiAg335i's Avatar
United_States
124
Rep
1,151
Posts

Drives: 10 e90 335i
Join Date: Mar 2010
Location: jacksonville, FL

iTrader: (10)

Garage List
2010 e90 335i  [7.00]
Quote:
Originally Posted by pablo86 View Post
Hi,

I have changed the LED's on my car and when I test the gauges with the needle sweep the speedo does not rotate around and back. It starts clicking and then stops.

I have reset the worm at the back and made sure it is all lined up ok but this does not change anything.

Is there anything else I can do or will i need to replace the cluster?

Many thanks
If it's clicking then the gears are not engaged or something is causing the needle to bind. As long as the motor is turning you should be able to get it to work. Good luck!
__________________

JB4, DP, VMR V710, Sonic Tuning S1 coilovers, Hybrid Ovations, Soundsplinter 10" and Zapco DC Ref amps
Appreciate 0
      12-31-2012, 01:19 PM   #98
cypis007
Private
Poland
0
Rep
83
Posts

Drives: E91 318d Touring
Join Date: Nov 2011
Location: Capital

iTrader: (0)

Here is how my cluster configuration looks now:





Custom faces + indiglo plates + pre-LCI needles + stock amber backlid
Appreciate 0
      01-04-2013, 04:36 AM   #99
greye90
Enlisted Member
2
Rep
31
Posts

Drives: 2008 335i sedan
Join Date: May 2012
Location: vancouver bc

iTrader: (0)

You have big balls doing this mod.

So awesome!
Appreciate 0
      01-09-2013, 12:32 AM   #100
Ducati848R
Captain
19
Rep
762
Posts

Drives: 06 325i
Join Date: May 2010
Location: Oregon

iTrader: (23)

Ordered my M3 needles and back plates and white LED's. Time to get modding!
Appreciate 0
      01-09-2013, 12:53 AM   #101
Imperator
Major
Imperator's Avatar
United_States
52
Rep
1,175
Posts

Drives: 2010 E92 335i
Join Date: Mar 2010
Location: Plano, Texas

iTrader: (8)

Quote:
Originally Posted by Ducati848R View Post
Ordered my M3 needles and back plates and white LED's. Time to get modding!
Where did you find the M3 needles?
Appreciate 0
      02-15-2013, 05:47 AM   #102
Tari
Captain
66
Rep
643
Posts

Drives: MG M4
Join Date: Dec 2009
Location: NY

iTrader: (0)

Anyone doing this i don't advise you use paint. Its too heavy for the needles and you wont get accurate reading anymore. Sharpie is better for this.
Appreciate 0
      02-16-2013, 09:41 AM   #103
e90TiAg335i
Major
e90TiAg335i's Avatar
United_States
124
Rep
1,151
Posts

Drives: 10 e90 335i
Join Date: Mar 2010
Location: jacksonville, FL

iTrader: (10)

Garage List
2010 e90 335i  [7.00]
Quote:
Originally Posted by Tari View Post
Anyone doing this i don't advise you use paint. Its too heavy for the needles and you wont get accurate reading anymore. Sharpie is better for this.
Really? I've used paint on several sets with zero isues. I use VHT nightshades red. Just a couple light coats and it comes out really well.
__________________

JB4, DP, VMR V710, Sonic Tuning S1 coilovers, Hybrid Ovations, Soundsplinter 10" and Zapco DC Ref amps
Appreciate 0
      03-09-2013, 04:08 PM   #104
joeyaoyp
Private
United_States
15
Rep
95
Posts

Drives: 2017 340i M-Sport 2008
Join Date: Nov 2012
Location: Houston,TX

iTrader: (0)

i bought the same led light as yours. but it is not so bright for mine.whats wrong?
Appreciate 0
      03-09-2013, 09:26 PM   #105
e90TiAg335i
Major
e90TiAg335i's Avatar
United_States
124
Rep
1,151
Posts

Drives: 10 e90 335i
Join Date: Mar 2010
Location: jacksonville, FL

iTrader: (10)

Garage List
2010 e90 335i  [7.00]
Quote:
Originally Posted by joeyaoyp View Post
i bought the same led light as yours. but it is not so bright for mine.whats wrong?
Not sure. Are you sure they're all lit up? Did you adjust the light setting?
__________________

JB4, DP, VMR V710, Sonic Tuning S1 coilovers, Hybrid Ovations, Soundsplinter 10" and Zapco DC Ref amps
Appreciate 0
      03-21-2013, 07:24 AM   #106
pablo86
Registered
0
Rep
3
Posts

Drives: 320d
Join Date: Sep 2012
Location: Cambridge

iTrader: (0)

Quote:
Originally Posted by e90TiAg335i View Post
If it's clicking then the gears are not engaged or something is causing the needle to bind. As long as the motor is turning you should be able to get it to work. Good luck!
Thanks. I ended up buying a second hand cluster and replacing the gear units.
Appreciate 0
      03-21-2013, 11:01 AM   #107
e90TiAg335i
Major
e90TiAg335i's Avatar
United_States
124
Rep
1,151
Posts

Drives: 10 e90 335i
Join Date: Mar 2010
Location: jacksonville, FL

iTrader: (10)

Garage List
2010 e90 335i  [7.00]
Quote:
Originally Posted by pablo86 View Post
Thanks. I ended up buying a second hand cluster and replacing the gear units.
Glad you got it worked out.
__________________

JB4, DP, VMR V710, Sonic Tuning S1 coilovers, Hybrid Ovations, Soundsplinter 10" and Zapco DC Ref amps
Appreciate 0
      03-21-2013, 12:16 PM   #108
boris
Борис
boris's Avatar
United_States
31
Rep
505
Posts

Drives: e92 n54 335i
Join Date: Nov 2012
Location: CT

iTrader: (1)

Great DIY....
__________________
07 SG 335i GONE!
COBB - Burger Motorsports -Ultimate Racing - Evolution Racewerks - TiAL- AMS

In Winter Mode - Dunlop Wintersport 3D/Sport Edition Wheels
Appreciate 0
      03-26-2013, 01:26 AM   #109
pt9507
M3 of the month(05/13)
pt9507's Avatar
Canada
23
Rep
261
Posts

Drives: BW E92 M3
Join Date: Feb 2012
Location: BC

iTrader: (2)

I really love the Custom faces...Did you DIY them?
Appreciate 0
      08-20-2013, 07:05 AM   #110
aadum
Second Lieutenant
aadum's Avatar
Croatia
80
Rep
233
Posts

Drives: 330xd e92 ,520d f10, 540i G30
Join Date: Aug 2011
Location: Split,Croatia

iTrader: (0)

a question.. if you put red LED's below needles are they going to be red or not? If I saw rigt OEM ones are white? Anyone ? I am about to do this mode so I need to know what to order
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 07:17 AM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST