|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
335Xi Performance Exhaust Install - DIY
|
|
09-06-2012, 01:55 AM | #23 |
Enlisted Member
5
Rep 31
Posts |
So I ran into a problem last weekend. The nuts which connect the downpipes to the midpipe were amazingly rusted. It was so bad that despite soaking for hours in PB blaster both lower nuts stripped when I tried to remove them. I ended up having to cut the nuts with half the stud off. Next step is to get the remains of the stud out of the downpipe flange... And that seems to require downpipe removal. I found a nice looking DIY for that (specifically for the xi). Never a dull moment :/
__________________
2007 E90 335xi
Cobb AccessPort, BMW Performance Exhaust |
Appreciate
0
|
09-06-2012, 06:37 AM | #24 | |
Second Lieutenant
12
Rep 224
Posts |
Quote:
|
|
Appreciate
0
|
09-06-2012, 10:03 AM | #26 | |
Private First Class
7
Rep 131
Posts |
Quote:
Normal drills will not last, you best need something like a tungsten drill. I used a lot of normal 6mm drills and it took me about 5hours. Then I bought a tungsten 6mm mill and could grind them out as you see in the pic. If you have acces to a cutting torch you can heat them up and and burn or hammer them out, but take care of your turbos. Good luck |
|
Appreciate
0
|
09-06-2012, 12:07 PM | #27 | |
Enlisted Member
5
Rep 31
Posts |
Quote:
I have already ground off the studs flush with the flange, and even the back of the stud also flush so I am ready to drill
__________________
2007 E90 335xi
Cobb AccessPort, BMW Performance Exhaust |
|
Appreciate
0
|
09-07-2012, 06:44 PM | #28 | |
Private First Class
7
Rep 131
Posts |
Quote:
As mill I bought a 6mm from top to tail, I then worked in circular moves until the studs became loose. But you need at least a hole of about 6mm to start, then the tungsten mill takes it with ease. You could even try to mill without completely drilling through, but you'll need some centering. Perhaps some shop owners/installers can chime in and tell us how they usually do it, I think this happens pretty often on higher mileage cars. If I had the possibility I would try the cutting torch. |
|
Appreciate
0
|
09-09-2012, 10:36 PM | #29 |
Enlisted Member
5
Rep 31
Posts |
Hi:
I finished this job at last - here follows my DIY. I hope this helps someone. It should be applicable for all E90's - not just the Xi model. Enjoy Jack the car up as high as possible. The front is straightforward - jacking point is a steel extrusion between the front wheels. I placed jack stands beneath the front jack points. Once I had lowered the car onto the jack stands, I left the jack in place as a 2nd line of defense. (the 2nd jack is not in this picture at this point). For the rear, I used a 4x4 piece of wood, about 10" in length on a second floor jack, placed at the point indicated in the picture: I used my longest jack stands here. They were placed as far to the left and right of the sub frame as possible. Next I removed the exhaust. I suppose you could (measure and) cut the exhaust pipes with it still mounted on the car and save an extra few steps, but I elected to remove the exhaust completely. I won't describe this in detail - its pretty straightforward starting with the 4 nuts attaching the exhaust to the down pipes to the nuts and bolts with secure the exhaust to the car with rubber blocks. One thing I did want to document here is nuts which hold the down pipes to the exhaust pipe. I found mine were terribly rusted - my car has ~45k miles and is a 2007. In my case, both 'upper' nuts were removable but the lower nuts were frozen in place and no amount of PB blaster would loosen. I ended up cutting off both nuts using a grinder. Once I removed the exhaust, I ground off what was left of the stud flush with the face of the down pipe flange and then used the tools/process suggested by Steve above to drill and then grind out the remains of the stud. When I reassembled the exhaust, I used bolts in place of the studs - worked very nicely. I used lots of anti-seize compound. My advice is to do all you can do to remove the frozen nuts - perhaps try a nut splitter or oxyacetylene torch to remove the nuts - I think I got a little impatient when I grabbed my grinder to solve the issue :-) OK, so once you have the exhaust removed, you can line them up and compare: I mapped over the dimensions of the new pipe by overlaying it on the old pipe, taking lots of measurements to make sure I made the cut line in the right place. Since the BMW exhaust pipe couplers will compensate for the pipe being cut slightly short (but not long) I erred on the side of cutting too short - by about 1/2". Making the cuts was not entirely easy. I had a pipe cutter I had loaned from a local tool place but that only allowed me to cut the longer of the 2 pipes. On the shorter one, the pipes are too close together to allow the cutter to access the pipe and so I ended up once again using my trusty grinder and hacksaw to cut the pipe. You should end up with something like this: Next mount the front exhaust pipe back on the car, making the front nuts just finger-tight. Use an axle stand at one end to support the pipe. Install 2 exhaust pipe couplers and place the middle exhaust section in place. You should be able to use the rubber exhaust mounts to keep it in place. Install another 2 exhaust pipe couplers on the rear of the middle section and install the left and right exhaust boxes. Use the 5th (small diameter) exhaust pipe coupler in he middle between the left and right boxes. Install the mounts to keep the mufflers in place. Note that at this point, I had not tightened anything. Once the entire exhaust was in position, I started at the down pipes and started tightening up all the nuts and bolts. All in all, it was not very difficult, and I would have been done in ~3 hours had it not been for the problem I encountered with the down pipe studs. The exhaust sounds excellent - I went for a drive today and was pleased :-) Cheers, Michael 2007 335xi Last edited by michaeldch; 10-02-2013 at 01:14 AM.. |
Appreciate
0
|
09-30-2012, 10:43 AM | #34 |
Brigadier General
398
Rep 4,084
Posts |
What did you do with the rubber tube connecting the flap on the drivers side?
__________________
7/18/09- I pick up my baby- 2009 E92 335i Xdrive, Space Gray over Coral Red. Premium Pkg, Cold Weather Pkg, M-Sport Pkg, 193Ms, Gloss Black grills, Custom Gloss Black Mirrors, Performance shift and E-brake boot, M3 spoiler, Euro fog switch, gloss black interior tim, Coco-Mats (red/black), H&R coilovers, 19'' Alufelgen SF-71s......
|
Appreciate
0
|
10-01-2012, 12:30 AM | #35 |
Enlisted Member
5
Rep 31
Posts |
I used a golf tee to block the rubber hose, then just tucked it behind the heat shield.
__________________
2007 E90 335xi
Cobb AccessPort, BMW Performance Exhaust |
Appreciate
0
|
07-17-2018, 10:09 PM | #36 |
Major
1169
Rep 1,479
Posts
Drives: 2008 BMW 335xi (E90)
Join Date: Mar 2018
Location: Michigan
|
Did this cause any issues or CEL?
__________________
Instagram: @4doors
Current: 2011 E91 328i M-Sport Touring Past: 2008 E90 335xi 1996 E36 328i Sport |
Appreciate
0
|
07-18-2018, 10:35 AM | #37 |
nub
3
Rep 8
Posts
Drives: 2008 E90 M3
Join Date: May 2017
Location: OH
|
FWIW, there is a cable to the exhaust flap that you can get to by removing the cover in the trunk by the left tail light.
Unplugging that cable will give you a CEL, but after I did an MHD flash with the cable unplugged the CEL never came back on for it. I'm guessing the ECU takes the current state of the world at the time of the flash as "how it should be" so it assumes there is no exhaust flap.
__________________
'08 E90 M3 6MT - SGM/BLK
|
Appreciate
0
|
07-20-2018, 03:55 PM | #38 |
Banned
298
Rep 650
Posts
Drives: Ferrari F430, E92 M3, 335xi
Join Date: Apr 2014
Location: Newton, MA
|
What , you left the secondary cats into place ?? I removed those, and my exhaust is louder than the PE exhaust now (I think), very pleasant to be honest... I think I gained like 50HP, as my cats were completely blocked, car woke up after that.
Cost me 200 bucks to remove them and weld some straight pipe. also, you have a leak from the diff... post a sound clip. |
Appreciate
0
|
Bookmarks |
|
|