|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Bmw 335i major oil leak
|
|
12-10-2018, 05:19 PM | #24 |
Enlisted Member
13
Rep 33
Posts |
My engine bay looks the same as MarkN54 so I believe we may be having the same issue. It is A LOT of oil coming out but the times I have fired it up I cannot see the exact location, it almost looks like it is coming from under the intake manifold near the alternator.
|
Appreciate
0
|
12-11-2018, 08:52 AM | #25 | |
Private
17
Rep 85
Posts |
Quote:
Are you talking about the plastic clip connectors by the front where the radiator is? So what I jus did was I replaced the crush washers on the banjo fittings and it’s still leaking so what I did was I double the crush washer and now it’s leaking even more... stupid mistake I guess |
|
Appreciate
0
|
12-11-2018, 08:55 AM | #26 |
Private
17
Rep 85
Posts |
[QUOTE=nsjames;24095877]if it were a high pressure side PS leak you'd know quickly.
low pressure side leaks are much more common.[/QUOTE How would I know? It leaks only when I drive not when it’s at idle I’m pretty sure I let it idle for and hour and no leaks drove 300 feet and I see oil on the ground |
Appreciate
0
|
12-11-2018, 11:02 AM | #27 |
Brigadier General
2440
Rep 4,330
Posts |
a few hundred PSI of hydraulic pressure is pretty hard to miss if it has a leak.
all of the high pressure side hoses are crimped style, they usually work or they fail. The low pressure side is just hoses and clamps, much more likely to have a slight leak. About the only place I would expect to see a slight weep on the high pressure side would be at the fittings themselves. |
Appreciate
0
|
12-11-2018, 12:10 PM | #28 |
Private
54
Rep 59
Posts |
I had serious oil leaks myself.
Changed the head cylinder valve cover gasket (it was dropping oil on the vacuum valve bracket, then dropping on the exhaust manifold: smoke was coming out). Normally, you can have oil leaks from the following on N54: - Oil Filter Housing gasket flange to cyl head - Oil Filter housing gasket flange to oil cooler - Cyl Head cover gasket - oil pan - Crank shaft seals I knew I was in for a big job, and was trying to avoid it... Then had no choice. I have decided to check engine compression first to determine engine's health condition. My compression was low. So I have elected to fix the engine at the same time as I'll fix the oil leaks. You can find the entire process (in progress) on my YouTube Channel. If you'd like to be posted when a new video is released, just subscribe. https://www.youtube.com/channel/UCrf...f2b4-fZVKDUi-w Here is the list of the videos that have been released so far Engine Removal is covered through 17 videos. 01 Underhood Shield Removal (Actual Youtube name: 01 BMW 135i N54 E82 - Engine Removal - Underhodd shield Removal) 02 Gas Pressure Relief (Actual Youtube name: 01 BMW 135i N54 E82 - Engine Removal - Gas Pressure Relief) 03 Air Cabin Filter and Engine Cover Removal 04 Intake Air Duct Removal 05 Radiator Fan Removal 06 Intercooler Removal 07 Throttle Body Air Pipe Removal 08 Vacuum Accumulators Removal 09 Water Pump Removal 10 Radiator and Thermostat Removal 11 Vacuum Valve Bracket Removal 12 Pre-Catalyst Removal 13 Belt, Accessories 1st step, Intake, Starter Removal 14 Exhaust, Heat Shield, Drive Shaft Removal 15 Transmission Removal 16 Accessories 2nd Step, Wiring, Fuel Line Removal 17 Engine Removal Final Engine Disassemble is to be covered in 8 videos 20 Oil Leaks Inspection, pulleys removal 21 Turbos removal 22 Cyl Head cover, coil packs and spark plugs, fuel rail removal 23 vacuum and high pressure pump removal 24 Timing chain 1 st step and cyl head removal 25 oil pan and pump removal Not finished released yet… 26 Fuel Injectors, Cams, Valves, Oil Filter Housing Removal You might want to take a look at this one... Hope it helps, |
Appreciate
2
Bimmer_Engineer1043.50 lab_rat394.50 |
01-07-2019, 01:11 PM | #29 | |
Private
17
Rep 85
Posts |
Quote:
|
|
Appreciate
0
|
01-07-2019, 04:26 PM | #30 |
Private
54
Rep 59
Posts |
Seems like mine was leaking from: oil filter housing (again), oil pan... These 2 mainly (highly probably more would have come soon, after 10 years...)
I had replaced cylinder head valve cover gasket not long ago (was dripping on vacuum valve bracket, then exhaust manifold). Knowing I was in for a good amount of work, I had the brilliant idea to check engine compression... It was low, very low. It seems like these engine are well thought. The cylinders and pistons are build to be relatively tough, but the compression rings are the one taking the wear. I would suggest people to really keep an eye on their compression as the N54 grows old. There was a guy on youtube that got given an engine (sorry can't recall his channel name). He's just going down on it, disassembling it all (without any plans to put it back together) just trying to see what went wrong... Compression ring broke, broke piston and create damage. I am glad I had the idea to check it. So I am joining all that amount of work at once. In the end, making it easier and avoiding myself to get involve in big work again in 1 or 2 years. Back at your oil leak... I would say that it seems that most sources seems to be: - oil filter housing to cyl head - oil filter housing to oil cooler hose flange (I would suggest to replace both at the same time when you're on it) - cyl head valve cover gasket - oil pan gasket - crankshaft seal (pulley side / front) - crankshaft seal (transmission side / rear) - Head gasket Don't think those are common, but I guess in extreme conditions, you can have leaks coming from: - turbos o'rings - turbos oil leaks accumulating in intake air ducts When looking at where the oil leaks are on your engine, you can figure the source of the leak. You are looking for gross fat mess, not light fume barely wet kind of thing. If it seems to be coming from under the head gasket... it looks like it might be it. I would think it is doable without removing the engine from the hood. But I would check compression, to do it all once if needed. Hope this answer/helps |
Appreciate
0
|
01-07-2019, 06:57 PM | #31 |
Fuck it dude, let's go bowling.
886
Rep 2,480
Posts |
__________________
1M. Previously: '13 135is; '07 E90 335i; '02 325i; '99 Z3; '98 328is; '87 L6; '77 320i
|
Appreciate
0
|
01-09-2019, 09:02 AM | #32 | |
Private
17
Rep 85
Posts |
Quote:
Last edited by MarkN54; 01-09-2019 at 09:27 AM.. |
|
Appreciate
0
|
01-11-2019, 09:36 AM | #33 |
Private
54
Rep 59
Posts |
Didn't had anything close to it, yet at least.
Not 100% sure, but I would suggest these: - try to run the engine idling with hood open to see if you can see where it comes from (watch your fingers with the belt obviously) - have someone give it a bit of gas to rev it up a bit, and hopefully with one of these 2 steps you might see where it comes from Else: - Check your turbo air duct that connects up front your engine (the one that you removed to take the 2nd picture. Check it for cracks as it might has oil in it trough time. - on mine, the turbo rubber seal in between the turbo and that duct was destroyed (on both turbos). I will replaced both of them with new ones (be careful, different part number). See part no 2 and 10 on realoem's link below http://www.realoem.com/bmw/enUS/show...diagId=13_1184 - The idea suggested by some others about the oil cooler pipes is also possible (didn't had that). I will replace the 4 O'rings on mine (1 o'ring at each end of pipes x 2 pipes (no 7 on realoem' link below) http://www.realoem.com/bmw/enUS/show...diagId=17_0375 - Cylinder head gasket leaking from the front is possible as per the picture I don't think it can be your vanos or cam sensors. There will be a trace of oil from them on the way down. As you seems to have fresh oil leaking on your pics, for some reasons, I would check the turbo duct a lot. I'd even go to put a thick zip-loc (for the freezer) with tie wraps on both end. One end having a longer one (so it has a bit of slack). Then I would make a little hole inserting a compressed air nozzle and spray a bit of air into it to see if there is a crack. Maybe 45 psi is enough. Be careful with that, a bit of air at the time (don't make it blow up your face!) Hoping that can help and that you'll find it. |
Appreciate
0
|
01-12-2019, 06:15 AM | #34 |
Lieutenant Colonel
480
Rep 1,600
Posts |
Not to be harsh but it is pointless trying to pinpoint a leak when your baseline is so dirty.
Go and buy some brake cleaner or water based degreaser (sodium hydroxide) and a large drip pan. Spend some time degreasing it thoroughly, dry it all off, then commence your examination. With a clean engine, and a leak that's as bad as yours it shouldn't take long to pinpoint. |
Appreciate
0
|
01-17-2019, 11:47 AM | #35 | |
Private
17
Rep 85
Posts |
Quote:
|
|
Appreciate
0
|
01-17-2019, 06:31 PM | #36 |
Lieutenant Colonel
480
Rep 1,600
Posts |
That's a very swollen coolant hose. Are you sure it isn't coolant you are losing? Possibly through a cracked plastic fitting to the head which can be broken during an oil filter housing repair.
If oil stains keep reappearing around the perimeter between the head and block, perhaps the head has been off before? Did you notice anything unusual when you took the valve cover off? One time I did have a persistent oil leak like yours. It turned out to be a bit of metal between the head gasket and the block. Last edited by juld0zer; 01-17-2019 at 06:38 PM.. |
Appreciate
0
|
01-17-2019, 11:26 PM | #37 | |
Private
8
Rep 95
Posts |
Quote:
|
|
Appreciate
0
|
01-18-2019, 09:59 AM | #39 | |
Private
17
Rep 85
Posts |
Quote:
|
|
Appreciate
0
|
01-22-2019, 09:55 AM | #41 | |
Private
17
Rep 85
Posts |
Quote:
|
|
Appreciate
1
Bimmer_Engineer1043.50 |
01-23-2019, 07:52 AM | #43 |
Private
17
Rep 85
Posts |
|
Appreciate
0
|
02-05-2019, 05:56 AM | #44 |
Lieutenant Colonel
480
Rep 1,600
Posts |
It's not good but if there was that much oil leaking out of the turbo inlet i think you'd be pumping out massive clouds of smoke also
Those seals also don't just fall out. Could a turbo/both turbos have been replaced? Damaged turbo oil feed/return? |
Appreciate
0
|
Bookmarks |
|
|