|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Bavarian Tech Code list
|
|
05-07-2009, 02:47 PM | #1 |
Enlisted Member
11
Rep 31
Posts |
Bavarian Tech Code list
Here is my contribution to you guys. I have put this together before and figured you all should benefit from it also. Add as you wish.
Thanks 2F6C: 2F6C Exhaust fumeflap, input signal Error will not cause a warning light Error is currently present Test conditions have been completed Timeout EXPLANATION: Unplugging actuator valve in trunk for added exhaust noise. FIX: Plugging back in and clearing code. *Code will not show up if you use the "golf tee mod" 2DEC: 2DEC Power management, battery control Error will not cause a warning light Error is not currently present Test conditions have been completed Signal or value below threshold EXPLANATION: Installing JB+ while the car did not go into sleep mode. FIX: Let car go into sleep mode, uninstall JB+ and reinstall it. Cleared code and never came back. EXPLANATION: Disconnecting battery FIX: Reconnect battery, clear and rescan. 2D18: 2D18 manipulation cover, maximum air mass Error will not cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption EXPLANATION: Tuner detection code FIX: Delete before service! 2D25C: 2D25 Mass Air Flow Excessive - External Tuning Box Detected Error will not cause a warning light Error is currently present Test conditions have been completed Short circuit or signal interruption EXPLANATION: Tuner detection code FIX: Delete before service! 2D1C 2D1C Accelerator pedal module, pedal sensor signal 2 Error will not cause a warning light Error is not currently present Test conditions have been completed Signal or value below threshold EXPLANATION: Gas pedal sensor or wiring issue FIX: 2FBF: 2FBF Fuel Pressure at Injection Release Error will not cause a warning light Error is currently present Short circuit or signal interruption EXPLANATION: Fuel pump pressure code FIX: Normally requires fuel pump replacement 2DED: 2DED Power management, standby current control Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: The closed circuit current momentarily exceeds its threshold value when the TCU wakes up to perform the "Stolen Vehicle Recovery" function. This should not cause a discharged battery. FIX: Take to dealer. 2D5A 2D5A Control motor torque limitation Error will not cause a warning light (it did cause a limp) Error is not currently present Test conditions have been completed EXPLANATION: FIX: 29DC: 29DC Cylinder injection switch-off Error will cause a warning light Error is not currently present Test conditions have not been completed Short circuit or signal interruption EXPLANATION: Fuel pump code FIX: Normally requires fuel pump replacement 2DC3: 2DC3 Control clamp 15 Error will not cause a warning light Error is not currently present Test conditions have been completed Timeout EXPLANATION: FIX: 2E8D: 2E8D Intelligent battery sensor, signal transmission Error will not cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption EXPLANATION: Small cable connected to battery has been removed FIX: 2F8F: 2F8F Accelerator pedal module and brake pedal, plausibility Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: Burnout FIX: Clear 29E2: 29E2 Fuel injection rail, pressure sensor signal Error will cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption EXPLANATION: Fuel pump code FIX: Normally requires fuel pump replacement 2A80: 2A80 Inlet-Vanos variable cam control test, input signal Error will cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: Requires dealer service, not related to tuning 2A85: 2A85 Outlet-VANOS variable cam control test Error will cause a warning light Error is not currently present Test conditions have been completed Timeout EXPLANATION: FIX: Requires dealer service, not related to tuning 2D58: 2D58 DME digital motor electronics, internal failure: control nominal torque? Error will cause a warning light Error is not currently present Test conditions have been completed Timeout EXPLANATION: FIX: 2EE0: 2EE0 Coolant temperature sensor, signal Error will cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption EXPLANATION: FIX: 2A9A: 2A9A Camshaft sensor inlet, signal Error will cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: 2ABC: 2ABC Charging pressure sensor, electrical Error will cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: ECU lost connection with tune. Unplugging map sensor or tune with ECU awake will cause this FIX: Clear code. If it comes back, check tune related wiring. 2ABD: 2ABD Intake pressure sensor, re-running Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: HPFP Failing? FIX:Take care into dealer 2FBE: 2FBE Fuel pressure after motor stop Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: Fuel pump code FIX: Normally requires fuel pump replacement 2AAF 2AAF Fuel Pump Plausibility Error will not cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption EXPLANATION: Fuel pump check. FIX: Very common code stock and modified alike, does not trigger a CEL. Just ignore it. 2A17 2A17 DMTL diagnosis module tank leakage, system failure Error will cause a warning light Error is not currently present Test conditions have been completed Timeout EXPLANATION: FIX: 2F0D: 2F0D Radiator blind, input signal, (GLF) Error will not cause a warning light Error is currently present Test conditions have been completed Timeout EXPLANATION: FIX: 30FE: 30FE Exhaust fume turbo charger, high pressure side Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: Boost too high FIX: Consult with your tuner. 30FF: 30FF, Exhaust fume turbocharger low side Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: Boost under target FIX: Check for boost leaks, and consult with your tuner. 30CF: 30CF Wastegate, input signal Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: Wastegate physically unplugged. FIX: Check wiring. Green and purple wires on JB3. 30D0: 30D0 Wastegate 2, input signal Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: Wastegate physically unplugged. FIX: Check wiring. Green and purple wires on JB3. 30F2: 30F2 Glow ignition: cylinder 6 Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: Super Knock in cylinder 6. FIX: Excessive knock retard. Lower boost levels, or run higher octane. 30F1: 30F1 Glow ignition: cylinder 5 Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: Super Knock in cylinder 5. FIX: Excessive knock retard. Lower boost levels, or run higher octane. 5088 Sensors gear selector switch Error will not cause a warning light Error is not currently present Test conditions have not been completed Timeout EXPLANATION: Transmission switch did not respond in allowable time????? FIX: Kick the shit out of the car and hope that it goes away 5DE1 DSC-ECU: ECU-internal: Clockstatus of the SP interface shows missing clock. Error will not cause a warning light Error is currently present Test conditions have been completed EXPLANATION: Codes from putting car on a dyno FIX: Clear and rescan 5DE0 DSC-ECU: ECU-internal: Plausibility of the VASP-U_Bit versus Uz power supply_clamp_15. Error will not cause a warning light Error is currently present Test conditions have been completed EXPLANATION: Codes from putting car on a dyno FIX: Clear and rescan 5E5B: Stability control Wheel speed sensor general: Long-term (several seconds) error suspicion of 3-4 RDF led to error mode. Error will not cause a warning light Error is not currently present EXPLANATION: NO IDEA PLEASE HELP??? Yes I know it should have this since its on the main page. FIX: Take to dealer? 5E40 5E40 Wheel speed sensor rear right: Signal edge missing(RDF-Typ11i). Error will cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: 5E1A 5E1A DSC-ECU: ECU-internal: Serial-Peripheral-Interface (SPI): Transmission failure multi IC. Error will cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: 51B0 51B0 DSC Signal not plausible: Brake pressure signal Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: A559 Clamp 30g_f cutoff Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: Pulled fuse out behind glovebox during tune install. FIX: Make sure fuse is inserted. Clear and rescan. A554 Alive telephone Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: A0B0 A0B0 Ecu input brake lights Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: Rear break bulb out. FIX:Take to dealer to replace bulb or replace bulb on your own. A375 A375 Communication with airbag ECU disturbed(Error_IBUS_CONNECTION_FAIL) Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: A092 A092 SHD Standardization 0xA092 Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: A3AD A3AD CAN ID 1D0 error: Engine data Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: A3AE A3AE CAN ID 0AA error: Idle engine speed Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: A8B6 A8B6 Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: A0B4 A0B4 Fault engine start starter Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: D356 D356 PT-CAN: Message TORQUE_3 (ID 0xAA) not received or wrong message length (DLC). [transmitter: DME] Error will cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: D355 D355 PT-CAN: Message TORQUE_2 (ID 0x0A9) not received or wrong message length (DLC). [transmitter: DME] Error will cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: D354 D354 PT-CAN: Message TORQUE_1 (ID 0xA8) not received or wrong message length (DLC). [transmitter: DME] Error will cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: D904 D904 K CAN wire error Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: E717 E717 CAN message: Dates of engine Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: E71A E71A CAN message: Torque 3 Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: 3100: 3100 boost-pressure control, deactivation Error will not cause warning light Error is not currently present Test conditions have been completed. EXPLANATION: This code is triggered any time you experience a 'limp' mode. FIX: This code itself is meaningless and serves only to let you know a 'limp mode' took place. 2AD0: 2AD0 Gear Control Error will not cause a warning light Error is currently present Test conditions have been completed EXPLANATION: This code is usually triggered simultaneously with the code CF33. It means that the transmission is in safe mode which may happen if engine module is replaced or the engine adaptation values are reset. FIX: Reset the transmission adaptation/learning values. CF33: Messages from engine control unit doesn't exist Error will cause a warning light Error is currently present Test conditions have been completed EXPLANATION: The transmission is in safe mode which may happen if engine module is replaced or the engine adaptation values are reset. FIX: Reset the transmission adaptation/learning values. 29D2 29D2 Misfirings, cylinder 6 Error will cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption EXPLANATION: FIX: 29D9 29D9 Misfirings in case of tank filling level too low Error will not cause a warning light Error is not currently present Test conditions have been completed Signal or value below threshold EXPLANATION: FIX: 29D1 29D1 Misfirings, cylinder 5 Error will cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption EXPLANATION: FIX: A127 Error ACK clamp 15 off before request Error will not cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption EXPLANATION: FIX: 6140 Redundance comparison driver steering angle high Error will cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: 2F9E: Termic oil level sensor Error will not cause a warning light EXPLANATION: Low Level Warning FIX: Change and/or add your oil. Take to dealer if you need to. 2A96: 2A96 Crankshaft sensor, tooth failure Error will cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption EXPLANATION: FIX: 2DC5: 2DC5 Torque requirement via CAN controller area network, plausibility Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: 51A6: Error engine signal Error will not cause a warning light Error is not currently present Test conditions have been completed Signal or value below threshold EXPLANATION: FIX: E18C Device didn't accept or confirm monitoring message (Error_Monitoring) Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: E18F Central registry does not match with debit configuration (Error_Registry_New) Error will not cause a warning light Error is not currently present Test conditions have been completed EXPLANATION: FIX: Last edited by #1Stunna; 05-07-2009 at 05:39 PM.. |
05-07-2009, 02:55 PM | #2 |
Major
82
Rep 1,389
Posts |
STICKY. PLEASE. Or put it in the DIY section.
__________________
"SYONRA" is for sale! http://www.e90post.com/forums/showthread.php?t=366678 BSM '09 e92 335i | Performance: JB3, RR Catted DP's, INJEN DCI, Britalman Exhst, AA FMIC, FORGE DVs | Suspension: ST-V1 Coils, Hotchkis Chassis Brace & F/R Sways | Wheels: Bremmer Kraft BR03s, Brake Performance Rotors, Cool Carbon Pads, ECS Lines | Exterior: OEM Aero Lip/Rear, ****** CF Trunk Lid, BLUX5 Angels, M-Force M3 Sides | Interior: Passport 9500ci, Black Trim, M3 Wheel
|
Appreciate
0
|
05-07-2009, 03:46 PM | #5 |
Team Zissou
3064
Rep 10,197
Posts |
I don't think I see 2F9E on your list
2F9E: Termic oil level sensor Error will not cause a warning light I'm think (see: not 100% sure) this shows up if you get a "low oil" warning |
Appreciate
0
|
05-07-2009, 04:40 PM | #6 |
Lieutenant
24
Rep 441
Posts |
my contribution to the list
29D2 29D2 Misfirings, cylinder 6 Error will cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption ________________________________________ 29D9 29D9 Misfirings in case of tank filling level too low Error will not cause a warning light Error is not currently present Test conditions have been completed Signal or value below threshold ________________________________________ 29D1 29D1 Misfirings, cylinder 5 Error will cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption ________________________________________ A127 Error ACK clamp 15 off before request Error will not cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption ________________________________________ 6140 Redundance comparison driver steering angle high Error will cause a warning light Error is not currently present Test conditions have been completed |
Appreciate
0
|
05-07-2009, 05:08 PM | #8 |
Lieutenant
77
Rep 418
Posts |
Thanks for all of your efforts on this, it is really helpful. This must have taken a lot of time and effort and I think that it is really helpful. Thanks again. Cheers!
|
Appreciate
0
|
05-07-2009, 05:12 PM | #9 |
Banned
2
Rep 88
Posts |
lol....Delta at least say who you really are.
The OP is delta bmw aka boostin4fun, etc. Cincy335i is one of his buddies who is trying to cover up for him. Delta, if you couldnt keep up with this list on another forum why start another one here? Good luck with your new name, I doubt it will last long once the mods and admins find out. Also, does anyone find it weird that a m3 owner complied a list of errors seen only by users with the n54 motor....odd. Give it up Delta, your banned from every forum. |
Appreciate
0
|
05-07-2009, 05:16 PM | #10 |
Vishnu Powered
68
Rep 2,205
Posts |
I think Delta got reinstated on these forums anyways. So whats the problem?
Can we keep this thread on topic so we can provide useful info.
__________________
2008 335xi Sedan | Titanium Silver | Black Dakota
PROcede v5 | Vishnu Exhaust | BMS DCI | AR Catless DPs | Helix FMIC | Stett Charge w/ Tial BOV | MORR VS8s | KWv3 |
Appreciate
0
|
05-07-2009, 05:16 PM | #11 |
Enlisted Member
11
Rep 31
Posts |
|
Appreciate
0
|
05-07-2009, 05:18 PM | #12 |
Banned
2
Rep 88
Posts |
|
Appreciate
0
|
05-07-2009, 05:22 PM | #13 |
Lieutenant
24
Rep 441
Posts |
another contribution to the list
2A96: 2A96 Crankshaft sensor, tooth failure Error will cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption 2DC5: 2DC5 Torque requirement via CAN controller area network, plausibility Error will not cause a warning light Error is not currently present Test conditions have been completed 51A6: Error engine signal Error will not cause a warning light Error is not currently present Test conditions have been completed Signal or value below threshold |
Appreciate
0
|
05-07-2009, 05:29 PM | #15 |
Lieutenant
77
Rep 418
Posts |
Who the hell are you, I don't see anything that says moderator next to your name? If you don't have anything to add to a useful thread, then move on, it really is that easy. Words of wisdom, don't start calling people out (me), when you have no idea what you are talking about...thanks.
|
Appreciate
0
|
05-07-2009, 05:29 PM | #16 | |
Enlisted Member
11
Rep 31
Posts |
Quote:
|
|
Appreciate
0
|
05-07-2009, 05:32 PM | #17 |
Lieutenant
24
Rep 441
Posts |
a little more....
Radio gateway Current Fault Codes ________________________________________ E18C Device didn't accept or confirm monitoring message (Error_Monitoring) Error will not cause a warning light Error is not currently present Test conditions have been completed ________________________________________ E18F Central registry does not match with debit configuration (Error_Registry_New) Error will not cause a warning light Error is not currently present Test conditions have been completed ________________________________________ |
Appreciate
0
|
05-07-2009, 05:39 PM | #18 | |
Enlisted Member
11
Rep 31
Posts |
Quote:
|
|
Appreciate
0
|
05-07-2009, 05:44 PM | #20 |
Vishnu Powered
68
Rep 2,205
Posts |
Are you the little taddle-tail kid who used to rat everyone out then get beat up at recess?
__________________
2008 335xi Sedan | Titanium Silver | Black Dakota
PROcede v5 | Vishnu Exhaust | BMS DCI | AR Catless DPs | Helix FMIC | Stett Charge w/ Tial BOV | MORR VS8s | KWv3 |
Appreciate
0
|
05-07-2009, 06:14 PM | #22 |
Banned
2
Rep 88
Posts |
|
Appreciate
0
|
Bookmarks |
|
|