|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
help coding LSMC and RSMC
|
|
02-05-2018, 08:31 PM | #1 |
Major
167
Rep 1,415
Posts |
help coding LSMC and RSMC
So about a week ago my LSMC fried from rain. Decided to take both headlights apart and mod them with new rings and some paint. I bought a used module and a used projector assembly which has the left right motor on it off ebay. 2 days ago I had Joe try to code both modules. The right side worked fine all directions but was slower to move than left side. The left side would only move up and down, and was stuck in the far right position. WTF...we couldn't figure it out. So i said maybe i got a bad module off ebay. I have another one coming and was supposed to be here today but never came....stupid USPS...hopefully tomorrow. Anyway i Went outside today to mess with coding. Maybe today will be different i thought....boy was i wrong....I coded left side.....IT MOVED LEFT TO RIGHT! WAHOO!!! then i noticed the right side would move right when i clicked left in INPA and right when i clicked left....wtf.....so i coded right side.....same thing happened.....i started cycling through the different positions in INPA. Then all of a sudden BOTH lights would only move up and down....OMG!! they were also both stuck in right position. So i thought let me switch the modules, since i read somewhere that the left is the master. I recoded both....started up and did its up down motion, went into INPA and WTF......same exact thing, let side is fine, right side does opposite, started cycling through positions in INPA and then both stop working left and right, only go up and down. I don't know what else to try. I check all the pins, cleaned them and applied dielectric grease. Also before i coded anything the right side worked perfectly. Left side didnt. but i thought it as just a coding issue. Joe told me that ISTA could run some tests? How do i do that? Please help me. This is really annoying... When i had the headlights opened I couldn't remember which position the cutoff line adjustment thing (see pic) was in. Also these are the codes i get. I got 9CBF and 9CC0 once but always get 9CC1 and 9CC2 (see pic). I would say it could be the motors, But they work....for a short time... Sorry for the long post. Let me know if anymore info is needed. Last thing done coding wise was my CIC retrofit
__________________
2007 335XI SEDAN // JB4 G5 // BMS METH KIT // VRSF DOWNPIPES // AFE DCI // ER CP W/ TIAL BOV // MMP SILICONE INLETS // XHP STAGE 3 AT FLASH // TREBILA BEF // BMS OCC // VRSF EXHAUST // FUEL-IT STAGE 2 LPFP // VRSF FMIC // PRECISION RACEWORKS IGNITION SYSTEM // CATUNED COILOVERS // CIC AND COMBOX RETROFIT //
Last edited by Maniac0908; 02-05-2018 at 08:43 PM.. |
02-06-2018, 09:14 PM | #4 |
Lieutenant
198
Rep 562
Posts |
In my experience, the adaptive headlights will do some funky stuff if you replace either SMC modules and not recode the NFRM because it still has values stored from your old modules.
|
Appreciate
0
|
02-06-2018, 09:24 PM | #5 |
Major
167
Rep 1,415
Posts |
how do i recode it? same as smc but choosing nfrm in NCS? if so, iv done that.... im about to smash my car with a sledge hammer.....
__________________
2007 335XI SEDAN // JB4 G5 // BMS METH KIT // VRSF DOWNPIPES // AFE DCI // ER CP W/ TIAL BOV // MMP SILICONE INLETS // XHP STAGE 3 AT FLASH // TREBILA BEF // BMS OCC // VRSF EXHAUST // FUEL-IT STAGE 2 LPFP // VRSF FMIC // PRECISION RACEWORKS IGNITION SYSTEM // CATUNED COILOVERS // CIC AND COMBOX RETROFIT //
|
Appreciate
0
|
02-06-2018, 09:28 PM | #6 |
Major
167
Rep 1,415
Posts |
one thing i noticed. when i turn my steering wheel, my flasher (h7) also called cornering lights? come on....this never used to happen. i dont think
__________________
2007 335XI SEDAN // JB4 G5 // BMS METH KIT // VRSF DOWNPIPES // AFE DCI // ER CP W/ TIAL BOV // MMP SILICONE INLETS // XHP STAGE 3 AT FLASH // TREBILA BEF // BMS OCC // VRSF EXHAUST // FUEL-IT STAGE 2 LPFP // VRSF FMIC // PRECISION RACEWORKS IGNITION SYSTEM // CATUNED COILOVERS // CIC AND COMBOX RETROFIT //
|
Appreciate
0
|
02-06-2018, 09:41 PM | #7 | |
Lieutenant
198
Rep 562
Posts |
Quote:
You need to change the build date in your VO back to your original one or one of a pre-lci then recode your NFRM and SMC modules. Last edited by siphor1989; 02-06-2018 at 09:48 PM.. |
|
Appreciate
0
|
02-06-2018, 10:00 PM | #8 | |
Major
167
Rep 1,415
Posts |
Quote:
|
|
Appreciate
0
|
02-06-2018, 10:12 PM | #9 | |
Lieutenant
198
Rep 562
Posts |
Quote:
Just don't use NCS expert to specifically code the CIC and it won't be affected. |
|
Appreciate
0
|
02-07-2018, 06:33 AM | #10 | |
Major
167
Rep 1,415
Posts |
Quote:
|
|
Appreciate
0
|
Bookmarks |
|
|